EEWORLDEEWORLDEEWORLD

Part Number

Search

MCP4341T-103E/ST

Description
Digital Potentiometer IC 10k SPI 7-bit Quad Chl, TSSOP20
CategoryAnalog mixed-signal IC    converter   
File Size2MB,81 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Environmental Compliance
Download Datasheet Download user manual Parametric View All

MCP4341T-103E/ST Overview

Digital Potentiometer IC 10k SPI 7-bit Quad Chl, TSSOP20

MCP4341T-103E/ST Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerMicrochip
Parts packaging codeTSSOP
package instructionTSSOP, TSSOP20,.25
Contacts20
Reach Compliance Codecompliant
ECCN codeEAR99
Factory Lead Time14 weeks
Nominal bandwidth1 kHz
control interface3-WIRE SERIAL
Converter typeDIGITAL POTENTIOMETER
JESD-30 codeR-PDSO-G20
JESD-609 codee3
length6.5 mm
Humidity sensitivity level1
Number of functions4
Number of positions129
Number of terminals20
Maximum operating temperature125 °C
Minimum operating temperature-40 °C
Package body materialPLASTIC/EPOXY
encapsulated codeTSSOP
Encapsulate equivalent codeTSSOP20,.25
Package shapeRECTANGULAR
Package formSMALL OUTLINE, THIN PROFILE, SHRINK PITCH
Peak Reflow Temperature (Celsius)260
power supply3/5 V
Certification statusNot Qualified
resistance lawLINEAR
Maximum resistor terminal voltage5.5 V
Minimum resistor terminal voltage
Maximum seat height1.2 mm
Nominal supply voltage2.7 V
surface mountYES
technologyCMOS
Nominal temperature coefficient150 ppm/°C
Temperature levelAUTOMOTIVE
Terminal surfaceMatte Tin (Sn) - annealed
Terminal formGULL WING
Terminal pitch0.65 mm
Terminal locationDUAL
Maximum time at peak reflow temperature40
Nominal total resistance10000 Ω
width4.4 mm
MCP434X/436X
7/8-Bit Quad SPI Digital POT with
Non-Volatile Memory
Features
• Quad Resistor Network
• Potentiometer or Rheostat configuration options
• Resistor Network Resolution
- 7-bit: 128 Resistors (129 Taps)
- 8-bit: 256 Resistors (257 Taps)
• R
AB
Resistances options of:
- 5 kΩ
- 10 kΩ
- 50 kΩ
- 100 kΩ
• Zero Scale to Full Scale Wiper operation
• Low Wiper Resistance: 75
Ω
(typical)
• Low Tempco:
- Absolute (Rheostat): 50 ppm typical
(0°C to 70°C)
- Ratiometric (Potentiometer): 15 ppm typical
• Non-volatile Memory
- Automatic Recall of Saved Wiper Setting
- WiperLock™ Technology
• SPI serial interface (10 MHz, modes 0,0 & 1,1)
- High-Speed Read/Writes to wiper registers
- Read/Write to Data EEPROM registers
- Serially enabled EEPROM write protect
• Resistor Network Terminal Disconnect Feature
via Terminal Control (TCON) Register
• Reset input pin
• Write Protect Feature:
- Hardware Write Protect (WP) Control pin
- Software Write Protect (WP) Configuration bit
• Brown-out reset protection (1.5V typical)
• Serial Interface Inactive current (2.5 uA typical)
• High-Voltage Tolerant Digital Inputs: Up to 12.5V
• Supports Split Rail Applications
• Internal weak pull-up on all digital inputs
• Wide Operating Voltage:
- 2.7V to 5.5V - Device Characteristics
Specified
- 1.8V to 5.5V - Device Operation
• Wide Bandwidth (-3 dB) Operation:
- 2 MHz (typical) for 5.0 kΩ device
• Extended temperature range (-40°C to +125°C)
Package Types (Top View)
MCP43X1
Quad Potentiometers
P3A
P3W
P3B
CS
SCK
SDI
V
SS
P1B
P1W
P1A
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
12
12
11
P2A
P2W
P2B
V
DD
SDO
RESET
WP
P0B
P0W
P0A
TSSOP
P3W
P2W
P2A
P3A
P2B
15
13
12
11
6
P1B
7
P1W
8
P1A
9 10
P0W
P0A
20 19 18 17 16
P3B
CS
SCK
SDI
V
SS
1
2
3
4
5
EP
21
V
DD
RESET
WP
P0B
14 SDO
4x4 QFN
MCP43X2
Quad Rheostat
P3W
P3B
CS
SCK
SDI
V
SS
P1B
1
2
3
4
5
6
7
14
13
12
11
10
9
8
TSSOP
P2W
P2B
V
DD
SDO
P0B
P0W
P1W
©
2009 Microchip Technology Inc.
DS22233A-page 1
Embedding web page related
Embedding web pages can realize basic functions such as submission. Using ssi and cgi methods The problem is as follows: 1. How to read the data on the board to the web page, and display the board's I...
longxtianya Microcontroller MCU
Why does 8086 require boundary alignment?
Why does 8086 require boundary alignment, that is, word addresses must be even addresses? What problems will occur if the boundaries are not aligned?...
liaorentai Embedded System
Application of AD8302 in Amplitude and Phase Detection System
This paper introduces the functions and features of the RF/IF amplitude and phase measurement chip AD8302, and gives a design scheme for the amplitude and phase detection system composed of this chip ...
rain Test/Measurement
What is the role of Link's cmd file?
Link's cmd file is used to locate the DSP code. Since the compilation result of the DSP compiler is not located, the DSP has no operating system to locate the execution code, and the configuration of ...
bolibo123 DSP and ARM Processors
Using stm32 to control ADS8332, what command can I write to ADS8332 to make it collect analog signals?
[b][color=#ff0000]Using stm32 to control ADS8332, what command should I write to ADS8332 to make it work and collect analog signals? I read the ADS8332 manual but still don't understand. Please help m...
se7enldp stm32/stm8
A small topic about power supply: How to select a power supply when designing it?
Power supply is a thing that will be involved in any electronic product. So if you want to design a power supply, how should you select it?How can we choose a chip that meets the design requirements, ...
okhxyyo Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2361  372  2889  2525  561  48  8  59  51  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号