At recommended operating conditions. Voltages are referenced to GND (ground = 0 V). T
amb
= -40 °C to +85 °C.
Symbol Parameter
V
IK
V
pass
I
I
I
CC
ΔI
CC
C
I
C
io(off)
C
io(on)
R
ON
input clamping voltage
pass voltage
input leakage current
supply current
additional supply current
input capacitance
off-state input/output
capacitance
on-state input/output
capacitance
ON resistance
Conditions
V
CC
= 4.5 V; I
I
= -18 mA
V
I
= V
CC
= 5.0 V; I
O
= -100 μA
V
CC
= 5.5 V; V
I
= GND or 5.5 V
V
CC
= 5.5 V; I
O
= 0 mA;V
I
= V
CC
or GND
per input; V
CC
= 5.5 V; one input at 3.4 V,
other inputs at V
CC
or GND
control pins; V
I
= 3 V or 0 V
A port; V
O
= 3 V or 0 V; nOE = V
CC
B port; V
O
= 3 V or 0 V; nOE = V
CC
A port and B port
V
CC
= 4.5 V
V
I
= 0 V; I
I
= 64 mA
V
I
= 0 V; I
I
= 30 mA
V
I
= 2.4 V; I
I
= -15 mA
[3]
[2]
Min
-
3.6
-
-
-
-
-
-
-
Typ
-
[1]
Max
-1.2
4.2
±1
3
2.5
-
-
-
-
Unit
V
V
μA
μA
mA
pF
pF
pF
pF
3.9
-
-
-
4.5
11.4
3.8
18.6
-
-
-
5
5
10
7
7
15
Ω
Ω
Ω
[1]
[2]
[3]
All typical values are measured at V
CC
= 5 V; T
amb
= 25 °C.
This is the increase in supply current for each input that is at the specified TTL voltage level rather than V
CC
or GND.
Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. The lowest voltage of the two (A or B)
terminals determines the ON resistance.
10 Dynamic characteristics
Table 7. Dynamic characteristics
T
amb
= -40 °C to +85 °C; V
CC
= 4.5 V to 5.5 V; for test circuit, see
Figure 6.
Symbol Parameter
t
pd
t
en
t
dis
propagation delay
enable time
disable time
Conditions
Sn to nA; see
Figure 4
nA to nBn or nBn to nA; see
Figure 4
Sn to nBn; see
Figure 5
nOE to nA or nBn; see
Figure 5
Sn to nBn; see
Figure 5
nOE to nA or nBn; see
Figure 5
[1] [2]
[1] [2]
[3]
[3]
[4]
[4]
Min
1.2
-
1.3
1.4
1.1
1.0
Max
6.2
0.25
6.3
6.4
7.2
7
Unit
ns
ns
ns
ns
ns
ns
[1]
[2]
[3]
[4]
This parameter is warranted but not production tested. The propagation delay is based on the RC time constant of the typical ON resistance of the switch
and a load capacitance, when driven by an ideal voltage source (zero output impedance).
t
PLH
and t
PHL
are the same as t
pd
.
t
PZL
and t
PZH
are the same as t
en
.
t
PLZ
and t
PHZ
are the same as t
dis
.
CBT3253A
All information provided in this document is subject to legal disclaimers.
Since it is not used much, only 2 bytes are needed to record the status when the power is off and no battery is considered. Although it is drawn on the board... Because it involves low power consumpti...
I uploaded the program to the attachment. Here I will talk about the pin connection between 5110 and launchpad: VCC: module power supply, the range is 2.7-3.3V, it is strongly recommended not to conne...
The company is making a zigbee module. Now the basic functions are complete. After the boss said that the module sensitivity needs to be tested, this task was assigned to me. I am responsible for the ...
1 Get Debian source codeUbuntu, Linux qt and Debian systems share a set of source code. For details on how to get Debian source code, refer to "13.1.1 Get Linux source code"2 Install Debian source cod...
Analog electronics
京公网安备 11010802033920号
EEWORLD
