OLED-096O064A-LPP3N00000
www.vishay.com
Vishay
96 x 64 Graphic OLED
FEATURES
• Type: graphic
• Display format: 96 x 64 dots
• Built-in controller: SSD1305Z
• Duty cycle: 1/64
• +3 V power supply
• Interface: 6800, 8080, SPI, I
2
C
• With polarizer
• Material categorization: for definitions of compliance
please see
www.vishay.com/doc?99912
MECHANICAL DATA
ITEM
Module dimension
Viewing area
Active area
Dot size
Dot pitch
Mounting hole
STANDARD VALUE
24.9 x 22.95 x 1.65
21.953 x 15.424
19.946 x 13.418
0.186 x 0.188
0.208 x 0.210
n/a
mm
UNIT
ABSOLUTE MAXIMUM RATINGS
ITEM
Supply voltage
for logic
(1)(2)
Supply voltage
for display
(1)(2)
Operating
temperature
Storage
temperature
SYMBOL
V
DD
V
CC
T
OP
T
STG
STANDARD VALUE
MIN.
-0.3
0
-40
-40
MAX.
4
V
15
+80
°C
+80
UNIT
Notes
(1)
All the above voltages are on the basis of “V
SS
= 0 V”
(2)
When this module is used beyond the above absolute maximum
ratings, permanent breakage of the module may occur. Also,
for normal operations, it is desirable to use this module under
the conditions according to “Electrical Characteristics”. If this
module is used beyond these conditions, malfunctioning of the
module can occur and the reliability of the module may
deteriorate
ELECTRICAL CHARACTERISTICS
ITEM
Supply voltage for logic
Supply voltage for display
Input high voltage
Input low voltage
Output high voltage
Output low voltage
50 % check board operating current
SYMBOL
V
DD
V
CC
V
IH
V
IL
V
OH
V
OL
I
CC
CONDITION
-
-
-
-
-
-
V
CC
= 12 V
STANDARD VALUE
MIN.
2.8
11
0.8 V
DD
0
0.9 V
DD
0
5.8
TYP.
3.0
12
-
-
-
-
6.0
MAX.
3.3
13
V
DDI/O
0.2 V
DD
V
DDI/O
0.1 V
DD
7.5
mA
V
UNIT
OPTIONS
EMITTING COLOR
YELLOW
Yes
GREEN
-
RED
-
BLUE
-
WHITE
-
Revision: 11-Aug-17
Document Number: 37835
1
For technical questions, contact:
displays@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
OLED-096O064A-LPP3N00000
www.vishay.com
Vishay
FUNCTION
INTERFACE PIN FUNCTION
PIN NO.
1
2
3
4
5
6
SYMBOL
NC (GND)
V
CC
V
SS
V
DD
V
DDI/O
BS1
I
7
8
9
BS2
CS#
RES#
I
I
I/O
-
P
P
P
P
Reserved pin (supporting pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be
connected to external ground
Power supply for OLED panel
This is the most positive voltage supply pin of the chip. It must be supplied externally
Ground of logic circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground
Power supply for logic circuit
This is a voltage supply pin. It must be connected to external source
Power supply for interface logic level. It should be match with MCU interface voltage level. V
DDI/O
must
always be equal or lower than V
DD
Communicating protocol select. These pins are MCU interface selection input. See the following table:
68XX-parallel
BS1
BS2
0
1
80XX-parallel
1
1
Serial
0
0
I
2
C
1
0
Chip select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low
Power reset for controller and driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed
Data / command control
This pin is data / command control pin. When the pin is pulled high, the input at D7 to D0 is treated as display
data.When the pin is pulled low, the input at D7 to D0 will be transferred to the command register. For detail
relationship to MCU interface signals, please refer to the timing characteristics diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When
it is pulled low, the data at SDIN will be transferred to the command register. In I
2
C mode, this pin acts as
SA0 for slave address selection
Read / write selector write
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as
read / write (R / W#) selection input. Pull this pin to “high” for read mode and pull it to “low” for write mode.
When 80XX interface mode is selected, this pin will be the write (WR#) input. Data write operation is initiated
when this pin is pulled low and the CS# is pulled low
Read / write enable or read
This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as
the enable (E) signal. Read / write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the read (RD#) signal. Data read operation
is initiated when this pin is pulled low and CS# is pulled low
10
D / C#
I
11
R / W#
I
12
E / RD#
I
13
14
15
16
17
18
19
20
21
I
REF
I
Current reference for brightness adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and V
SS
. Set the
current lower than 10 μA
Voltage output high level for COM signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected
between this pin and V
SS
Power supply for OLED panel
This is the most positive voltage supply pin of the chip. It must be supplied externally
Ground of analog circuit. This is an analog ground pin. It should be connected to V
SS
externally
Reserved pin (supporting pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be
connected to external ground
D0 to D7
I/O
Host data in put / output bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial
mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I
2
C
mode is selected, D2 and D1 should be tired together and serve as SDA
out
and SDA
in
in application and D0
is the serial clock input SCL
22
23
24
25
V
COMH
V
CC
V
LSS
NC (GND)
O
P
P
-
Revision: 11-Aug-17
Document Number: 37835
2
For technical questions, contact:
displays@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Analog electronics
京公网安备 11010802033920号
EEWORLD
