10 to 55 Hz at double amplitude of 1.5 mm (detection time: 10μs) (Only the NC contact of 1 Form C is 0.82mm)
10 to 55 Hz at double amplitude of 1.5 mm
Min. 1×10
6
(at 180 times/min.)
Ambient temperature: –40 to +85°C
–40 to +185°F
(Class B insulation), –40 to +105°C
–40 to +221°F
(Class F
insulation),
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
Approx. 11 g
.39 oz
Specifications
Notes: *1.This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of
±1.2×50μs
according to JEC-212-1981
*3. For the ambient temperature, please refer to Usage, transport and storage conditions in NOTES.
*Please note that some of the specifications listed above may not comply with overseas standards.
3. Expected electrical life
Condition: Resistive, at 20°C
68°F
Type
1 Form A
NO contact
1 Form C
NC contact
For the operating ambient temperature, please read the notes
16A 250V AC
Switching capacity
16A 250V AC
16A 250V AC
Number of operations
Min. 1×10
5
(ON:OFF = 1.5s:1.5s)
Min. 5×10
4
(ON:OFF = 1.5s:1.5s)
Min. 1×10
4
(ON:OFF = 1.5s:1.5s)
–2–
ASCTB395E 201809-T
LZ-N (ALZN)
REFERENCE DATA
1. Max. switching capacity (AC resistive load)
2. Coil temperature rise (Ave.)
Tested sample: ALZN1F12, 6pcs.
Contact current: 16A
Ambient temperature: Normal temperature • 85°C
185°F
• 105°C
221°F
Measured portion: inside the coil
100
50
30
20
10
5
65
Normal temperature 16A
Coil applied voltage, %V
60
Temperature rise,
°C
55
50
45
40
35
30
50
25
0
30
100
500 1,000
Contact voltage, V
20
95 100 105 110 115 120 125 130 135
Coil applied voltage, %V
0
0
85°C 16A
105°C 16A
3. Ambient temperature characteristics (Ave.)
Tested sample: ALZN1F12, 6pcs.
Contact carrying current: 0A, 16A
Measured portion: inside the coil
300
250
16A 155°C
Contact current, A
200
150
100
16A 130°C
Operate voltage
(Hot start: 16A, 100%V)
1
0.5
Operate voltage
(Cold start: Coil and contact no carrying current)
20
40
60
80
100
Ambient temperature,
°C
120
DIMENSIONS
(mm
inch)
1. 1 Form A type
The CAD data of the products with a “CAD” mark can be downloaded from our Website.
usbmsd_rom routine analysis:
1. Map the pointer to the on-chip driver table:ROM ** rom = (ROM **) 0x1fff1ff8;
2. Set device type and information:
MscDevInfo.idVendor = USB_VENDOR_ID ;MscDevInfo.idProd...
void CTL74ls138(unsigned char m,unsigned char n,unsigned char l) { P1OUT = m<<1 | n<<3 | l<<4; } What does this program mean? The A, B, and C of 74LS138 are connected to P1.1, P1.3, and P1.4 of msp430...
[i=s]This post was last edited by youzizhile on 2016-7-1 20:38[/i] I received a call from FedEx today. I think it must be the cc2650 development board. I quickly retrieved the package, but found that ...
[size=7]Use SourceInsight to view LPCOpen source code[size=3] Since LPCOpen routines are compiled libraries, it is very inconvenient to view the source code in Keil routines. You can only view it by a...
1. Recommended domestic FPGA manufacturers: Tsinghua Unigroup
It has a certain ability to replace FPGA industrial boards. For example, for the PGL12G chip, ALINX has relatively matching development ki...
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
As LEDs continue to improve in almost every aspect of performance and cost, LED lighting is being used in an increasingly wide range of applications, among which LED street lights are a focus of in...[Details]
D5026A is a driver IC designed by Shanghai Debei Electronics for energy-saving LED display screens. Its design concept is energy-saving and compatible with existing solutions, that is, it can be ...[Details]
Key Points
1. Now, in addition to high-end smartphones and tablets, users also expect to use touch screens in other applications, and they are gradually appearing in cars and instruments.
...[Details]
Analysis of the three core aspects of digital TV transmission standards
According to the differences in regionality, transmission method and modulation method, the transmission method needs to...[Details]
The principles to be followed are as follows:
(1) In terms of component layout, related components should be placed as close as possible. For example, clock generators, crystal oscillat...[Details]
1. Introduction
Modern modular machine tools are equipped with a large number of electronic devices to meet the requirements of processing accuracy, processing speed, etc. If the conventional ...[Details]
Abstract: Based on the analysis of the characteristics of the IRIG-B (DC) code type, a design method for IRIG-B (DC) time code decoding is proposed. This method consists of a small number of periph...[Details]
Traditional synthesis techniques are increasingly unable to meet the needs of today's very large and complex FPGA designs implemented in 90nm and below process nodes. The problem is that traditio...[Details]
TMC428 is a stepper motor motion controller from TRINAMIC. It can reduce the workload of motor control software design and development costs. The 3-axis stepper motor drive control system based on ...[Details]
1. Sensor
According to the national standard GB7665-87, a sensor is defined as a device that can sense the specified measured quantity and convert it into a usable output signal according to a...[Details]
The Challenge:
Protect historical relics by monitoring environmental factors without affecting their original appearance.
The Solution:
Developed a monitoring system for the...[Details]
O Introduction
For people who are in the wild, a question that they are more concerned about is the altitude of the place where they are. However, there are very few such products on the mar...[Details]
Example of multitasking and resource reuse of programs
There is an electromechanical device with two buttons that control two different parts of the device.
Now the requirement is:
wh...[Details]
NXP MCU
京公网安备 11010802033920号
EEWORLD
