512Mb, 3V Multiple I/O Serial Flash Memory
Features
Micron Serial NOR Flash Memory
3V, Multiple I/O, 4KB, 32KB, 64KB, Sector Erase
MT25QL512ABB
Features
• SPI-compatible serial bus interface
• Single and double transfer rate (STR/DTR)
• Clock frequency
– 133 MHz (MAX) for all protocols in STR
– 90 MHz (MAX) for all protocols in DTR
• Dual/quad I/O commands for increased through-
put up to 90 MB/s
• Supported protocols in both STR and DTR
– Extended I/O protocol
– Dual I/O protocol
– Quad I/O protocol
• Execute-in-place (XIP)
• PROGRAM/ERASE SUSPEND operations
• Volatile and nonvolatile configuration settings
• Software reset
• Reset pin available
• 3-byte and 4-byte address modes – enable memory
access beyond 128Mb
• Dedicated 64-byte OTP area outside main memory
– Readable and user-lockable
– Permanent lock with PROGRAM OTP command
• Erase capability
– Bulk erase
– Sector erase 64KB uniform granularity
– Subsector erase 4KB, 32KB granularity
• Security and write protection
– Volatile and nonvolatile locking and software
write protection for each 64KB sector
– Nonvolatile configuration locking
– Password protection
– Hardware write protection: nonvolatile bits
(BP[3:0] and TB) define protected area size
– Program/erase protection during power-up
– CRC detects accidental changes to raw data
• Electronic signature
– JEDEC-standard 3-byte signature (BA20h)
– Extended device ID: two additional bytes identify
device factory options
• JESD47H-compliant
– Minimum 100,000 ERASE cycles per sector
– Data retention: 20 years (TYP)
Options
• Voltage
– 2.7–3.6V
• Density
– 512Mb
• Device stacking
– Monolithic
• Device generation
• Die revision
• Pin configuration
– HOLD#
– RESET# and HOLD#
• Sector Size
– 64KB
• Packages – JEDEC-standard, RoHS-
compliant
– 24-ball T-PBGA 05/6mm × 8mm
(TBGA24)
– 16-pin SOP2, 300 mil
(SO16W, SO16-Wide, SOIC-16)
– W-PDFN-8 8mm × 6mm
(MLP8 8mm × 6mm)
• Security features
– Standard security
• Special options
– Standard
– Automotive
• Operating temperature range
– From –40°C to +85°C
– From –40°C to +105°C
– From –40°C to +125°C
Marking
L
512
A
B
B
1
8
E
12
SF
W9
0
S
A
IT
AT
UT
09005aef864f8d51
MT25Q_QLKT_L_512_ABB_0.pdf - Rev. F 1/18 EN
1
Products and specifications discussed herein are subject to change by Micron without notice.
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
512Mb, 3V Multiple I/O Serial Flash Memory
Features
Part Number Ordering
Micron Serial NOR Flash devices are available in different configurations and densities. Verify valid part numbers
by using Micron’s part catalog search at www.micron.com. To compare features and specifications by device type,
visit www.micron.com/products. Contact the factory for devices not found.
Figure 1: Part Number Ordering Information
MT 25Q L
Micron Technology
Part Family
25Q = SPI NOR
Voltage
L = 2.7–3.6V
U = 1.7–2.0V
Density
064 = 64Mb (8MB)
128 = 128Mb (16MB)
256 = 256Mb (32MB)
512 = 512Mb (64MB)
01G = 1Gb (128MB)
02G = 2Gb (256MB)
Stack
A = 1 die/1 S#
B = 2 die/1 S#
C = 4 die/1 S#
Device Generation
B = 2nd generation
Die Revision
A = Rev. A
B = Rev. B
Pin Configuration Option
1 = HOLD# pin
3 = RESET# pin
8 = RESET# and HOLD# pin
xxx
A
BA
1
E
SF - 0
S
IT
ES
Production Status
Blank = Production
ES = Engineering samples
QS = Qualification samples
Operating Temperature
IT = –40°C to +85°C
AT = –40°C to +105°C
UT = –40°C to +125°C
Special Options
S = Standard
A = Automotive grade AEC-Q100
Security Features
0 = Standard default security
Package Codes
12 = 24-ball T-PBGA, 05/6 x 8mm (5 x 5 array)
14 = 24-ball T-PBGA, 05/6 x 8mm (4 x 6 array)
SC = 8-pin SOP2, 150 mil
SE = 8-pin SOP2, 208 mil
SF = 16-pin SOP2, 300 mil
W7 = 8-pin W-PDFN, 6 x 5mm
W9 = 8-pin W-PDFN, 8 x 6mm
5x = WLCSP package
1
Sector size
E = 64KB sectors, 4KB and 32KB sub-sectors
Note:
1. WLCSP package codes, package size, and
availability are density-specific. Contact the
factory for availability.
09005aef864f8d51
MT25Q_QLKT_L_512_ABB_0.pdf - Rev. F 1/18 EN
2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
512Mb, 3V Multiple I/O Serial Flash Memory
Features
Contents
Important Notes and Warnings ......................................................................................................................... 9
Device Description ......................................................................................................................................... 10
Device Logic Diagram ................................................................................................................................. 11
Advanced Security Protection ..................................................................................................................... 11
Signal Assignments – Package Code: 12 ........................................................................................................... 12
Signal Assignments – Package Code: SF ........................................................................................................... 13
Signal Assignments – Package Code: W9 .......................................................................................................... 13
Signal Descriptions ......................................................................................................................................... 14
Package Dimensions – Package Code: 12 ......................................................................................................... 16
Package Dimensions – Package Code: SF ......................................................................................................... 17
Package Dimensions – Package Code: W9 ........................................................................................................ 18
Memory Map – 512Mb Density ....................................................................................................................... 19
Status Register ................................................................................................................................................ 20
Block Protection Settings ............................................................................................................................ 21
Flag Status Register ......................................................................................................................................... 22
Extended Address Register .............................................................................................................................. 23
Internal Configuration Register ....................................................................................................................... 24
Nonvolatile Configuration Register .................................................................................................................. 25
Volatile Configuration Register ........................................................................................................................ 27
Supported Clock Frequencies ..................................................................................................................... 28
Enhanced Volatile Configuration Register ........................................................................................................ 31
Security Registers ........................................................................................................................................... 32
Sector Protection Security Register .................................................................................................................. 33
Nonvolatile and Volatile Sector Lock Bits Security ............................................................................................ 34
Volatile Lock Bit Security Register .................................................................................................................... 34
Device ID Data ............................................................................................................................................... 35
Serial Flash Discovery Parameter Data ............................................................................................................. 36
Command Definitions .................................................................................................................................... 37
Software RESET Operations ............................................................................................................................ 43
RESET ENABLE and RESET MEMORY Commands ....................................................................................... 43
READ ID Operations ....................................................................................................................................... 44
READ ID and MULTIPLE I/O READ ID Commands ...................................................................................... 44
READ SERIAL FLASH DISCOVERY PARAMETER Operation .............................................................................. 45
READ SERIAL FLASH DISCOVERY PARAMETER Command ......................................................................... 45
READ MEMORY Operations ............................................................................................................................ 46
4-BYTE READ MEMORY Operations ................................................................................................................ 47
READ MEMORY Operations Timings ............................................................................................................... 48
WRITE ENABLE/DISABLE Operations ............................................................................................................. 55
READ REGISTER Operations ........................................................................................................................... 56
WRITE REGISTER Operations ......................................................................................................................... 57
CLEAR FLAG STATUS REGISTER Operation ..................................................................................................... 59
PROGRAM Operations .................................................................................................................................... 60
4-BYTE PROGRAM Operations ........................................................................................................................ 61
PROGRAM Operations Timings ....................................................................................................................... 61
ERASE Operations .......................................................................................................................................... 64
SUSPEND/RESUME Operations ..................................................................................................................... 66
PROGRAM/ERASE SUSPEND Operations .................................................................................................... 66
PROGRAM/ERASE RESUME Operations ...................................................................................................... 66
ONE-TIME PROGRAMMABLE Operations ....................................................................................................... 68
READ OTP ARRAY Command ...................................................................................................................... 68
09005aef864f8d51
MT25Q_QLKT_L_512_ABB_0.pdf - Rev. F 1/18 EN
3
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
512Mb, 3V Multiple I/O Serial Flash Memory
Features
PROGRAM OTP ARRAY Command ..............................................................................................................
ADDRESS MODE Operations ..........................................................................................................................
ENTER and EXIT 4-BYTE ADDRESS MODE Command ................................................................................
DEEP POWER-DOWN Operations ...................................................................................................................
ENTER DEEP POWER-DOWN Command ....................................................................................................
RELEASE FROM DEEP POWER-DOWN Command .......................................................................................
DEEP POWER-DOWN Timings ....................................................................................................................
QUAD PROTOCOL Operations ........................................................................................................................
ENTER or RESET QUAD INPUT/OUTPUT MODE Command .......................................................................
CYCLIC REDUNDANCY CHECK Operations ....................................................................................................
State Table .....................................................................................................................................................
XIP Mode .......................................................................................................................................................
Activate and Terminate XIP Using Volatile Configuration Register .................................................................
Activate and Terminate XIP Using Nonvolatile Configuration Register ..........................................................
Confirmation Bit Settings Required to Activate or Terminate XIP ..................................................................
Terminating XIP After a Controller and Memory Reset .................................................................................
Power-Up and Power-Down ............................................................................................................................
Power-Up and Power-Down Requirements ..................................................................................................
Active, Standby, and Deep Power-Down Modes ................................................................................................
Power Loss and Interface Rescue .....................................................................................................................
Recovery ....................................................................................................................................................
Power Loss Recovery ...................................................................................................................................
Interface Rescue .........................................................................................................................................
Initial Delivery Status .....................................................................................................................................
Absolute Ratings and Operating Conditions .....................................................................................................
DC Characteristics and Operating Conditions ..................................................................................................
AC Characteristics and Operating Conditions ..................................................................................................
AC Reset Specifications ...................................................................................................................................
Program/Erase Specifications .........................................................................................................................
Revision History .............................................................................................................................................
Rev. F - 1/18 ...............................................................................................................................................
Rev. E – 06/17 .............................................................................................................................................
Rev. D – 06/16 .............................................................................................................................................
Rev. C – 06/16 .............................................................................................................................................
Rev. B – 02/16 .............................................................................................................................................
Rev. A – 06/15 .............................................................................................................................................
68
70
70
71
71
71
72
74
74
75
77
78
78
78
79
79
80
80
82
83
83
83
83
84
85
87
89
92
96
97
97
97
97
97
97
97
09005aef864f8d51
MT25Q_QLKT_L_512_ABB_0.pdf - Rev. F 1/18 EN
4
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
512Mb, 3V Multiple I/O Serial Flash Memory
Features
List of Figures
Figure 1: Part Number Ordering Information .................................................................................................... 2
Figure 2: Block Diagram ................................................................................................................................ 10
Figure 3: Logic Diagram ................................................................................................................................. 11
Figure 4: 24-Ball T-BGA, 5 × 5 (Balls Down) ..................................................................................................... 12
Figure 5: 16-Pin, Plastic Small Outline – SO16 (Top View) ................................................................................ 13
Figure 6: 8-Pin, W-PDFN (Top View) .............................................................................................................. 13
Figure 7: 24-Ball T-PBGA (5 × 5 ball grid array) – 6mm × 8mm ......................................................................... 16
Figure 8: 16-Pin SOP2 – 300 mil Body Width ................................................................................................... 17
Figure 9: W-PDFN-8 (MLP8) – 8mm × 6mm .................................................................................................... 18
Figure 10: Memory Array Segments ................................................................................................................ 23
Figure 11: Internal Configuration Register ...................................................................................................... 24
Figure 12: Sector and Password Protection ..................................................................................................... 32
Figure 13: RESET ENABLE and RESET MEMORY Command ........................................................................... 43
Figure 14: READ ID and MULTIPLE I/O READ ID Commands ......................................................................... 44
Figure 15: READ SERIAL FLASH DISCOVERY PARAMETER Command – 5Ah ................................................... 45
Figure 16: READ – 03h/13h
3
........................................................................................................................... 48
Figure 17: FAST READ – 0Bh/0Ch
3
................................................................................................................. 48
Figure 18: DUAL OUTPUT FAST READ – 3Bh/3Ch
3
......................................................................................... 49
Figure 19: DUAL INPUT/OUTPUT FAST READ – BBh/BCh
3
............................................................................ 49
Figure 20: QUAD OUTPUT FAST READ – 6Bh/6Ch
3
........................................................................................ 50
Figure 21: QUAD INPUT/OUTPUT FAST READ – EBh/ECh
3
............................................................................ 50
Figure 22: QUAD INPUT/OUTPUT WORD READ – E7h
3
................................................................................. 51
Figure 23: DTR FAST READ – 0Dh/0Eh
3
.......................................................................................................... 52
Figure 24: DTR DUAL OUTPUT FAST READ – 3Dh
3
........................................................................................ 52
Figure 25: DTR DUAL INPUT/OUTPUT FAST READ – BDh
3
............................................................................ 53
Figure 26: DTR QUAD OUTPUT FAST READ – 6Dh
3
........................................................................................ 54
Figure 27: DTR QUAD INPUT/OUTPUT FAST READ – EDh
3
............................................................................ 54
Figure 28: WRITE ENABLE and WRITE DISABLE Timing ................................................................................. 55
Figure 29: READ REGISTER Timing ................................................................................................................ 56
Figure 30: WRITE REGISTER Timing .............................................................................................................. 58
Figure 31: CLEAR FLAG STATUS REGISTER Timing ........................................................................................ 59
Figure 32: PAGE PROGRAM Command .......................................................................................................... 61
Figure 33: DUAL INPUT FAST PROGRAM Command ...................................................................................... 62
Figure 34: EXTENDED DUAL INPUT FAST PROGRAM Command ................................................................... 62
Figure 35: QUAD INPUT FAST PROGRAM Command ..................................................................................... 63
Figure 36: EXTENDED QUAD INPUT FAST PROGRAM Command ................................................................... 63
Figure 37: SUBSECTOR and SECTOR ERASE Timing ....................................................................................... 65
Figure 38: BULK ERASE Timing ...................................................................................................................... 65
Figure 39: PROGRAM/ERASE SUSPEND and RESUME Timing ........................................................................ 67
Figure 40: READ OTP Command Timing ........................................................................................................ 68
Figure 41: PROGRAM OTP Command Timing ................................................................................................. 69
Figure 42: ENTER DEEP POWER-DOWN Timing ............................................................................................. 72
Figure 43: RELEASE FROM DEEP POWER-DOWN Timing ............................................................................... 73
Figure 44: XIP Mode Directly After Power-On .................................................................................................. 78
Figure 45: Power-Up Timing .......................................................................................................................... 81
Figure 46: AC Timing Input/Output Reference Levels ...................................................................................... 86
Figure 47: Reset AC Timing During PROGRAM and ERASE Cycle ..................................................................... 93
Figure 48: Reset Enable and Reset Memory Timing ......................................................................................... 93
Figure 49: Serial Input Timing STR ................................................................................................................. 93
Figure 50: Serial Input Timing DTR ................................................................................................................ 94
09005aef864f8d51
MT25Q_QLKT_L_512_ABB_0.pdf - Rev. F 1/18 EN
5
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2013 Micron Technology, Inc. All rights reserved.
京公网安备 11010802033920号
EEWORLD
