Sil-Pad
®
1200
January 2015
PRODUCT DESCRIPTION
Exceptional Performance, Thermally
Conductive Elastomeric Material
FEATURES AND BENEFITS
• Thermal Impedance: 0.53oC-in
2
/W
(@ 50 psi)
• Exceptional thermal performance at
lower application pressures
• Smooth and non-tacky on both sides
for easy re-positioning, ease of use
and assembly error reduction
• Superior breakdown voltage and
surface “wet out” values
• Designed for applications where
electrical isolation is critical
• Excellent cut-through resistance,
designed for screw and clip
mounted applications
PROPERTY
Color
TYPICAL PROPERTIES OF SIL-PAD 1200
IMPERIAL VALUE
Black
Fiberglass
0.009 to 0.016
80
20
1300
-76 to 356
6000
8.0
10
9
METRIC VALUE
Black
Fiberglass
0.229 to 0.406
80
20
9
-60 to 180
6000
8.0
10
9
TEST METHOD
Visual
—
ASTM D374
ASTM D2240
ASTM D412
ASTM D412
—
ASTM D149
ASTM D150
ASTM D257
U.L. 94
ASTM D5470
Reinforcement Carrier
Thickness (inch) / (mm)
Hardness Bulk Rubber (Shore 00)
Elongation (% at 45º to warp and fill)
Tensile Strength (psi) / (MPa)
Continuous Use Temp (°F) / (°C)
ELECTRICAL
Dielectric Breakdown Voltage (Vac)
Dielectric Constant (1000 Hz)
Volume Resistivity (Ohm-meter)
Flame Rating
THERMAL
Thermal Conductivity (W/m-K) (1)
THERMAL PERFORMANCE
VS
V-O
1.8
10
2.82
0.71
25
2.64
0.62
V-O
1.8
50
2.41
0.53
PRESSURE
100
2.13
0.47
200
1.90
0.41
Pressure (psi)
TO-220 Thermal Performance (ºC/W)
Thermal Impedance (ºC-in
2
/W) (2)
1)This is the measured thermal conductivity of the Sil-Pad Compound.
2) The ASTM D5470 test fixture was used. The recorded value includes interfacial thermal resistance. These values are provided for
reference only. Actual application performance is directly related to the surface roughness, flatness and pressure applied.
TYPICAL APPLICATIONS INCLUDE
• Automotive electronics control modules
• Power supplies
• Motor controls
Sil-Pad
®
1200 is a silicone based,
fiberglass-reinforced thermal interface
material featuring a smooth, highly
compliant surface. The material features
a non-tacky surface for efficient
re-positioning and ease of use, as well
as an optional adhesive coating.
Sil-Pad
®
1200 exhibits exceptional thermal
performance at low and high application
pressures. The material is ideal for
placement between electronic power
devices and a heatsink for screw and
clip mounted applications.
Note: To build a part number, visit our
website at www.bergquistcompany.com.
• Audio amplifiers
• Discrete devices
• Telecommunications
CONFIGURATIONS AVAILABLE
• Sheet form, slit-to-width roll form
• Die-cut parts
• 9, 12 and 16 mil thicknesses
• Adhesive coating
We produce thousands of specials and customs.
Tooling charges vary depending on tolerances and complexity of the part.
PDS_SP_1200_0115
TDS Sil-Pad
®
1200, January 2015
Disclaimer
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In
case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Corporation, Resin Technology
Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
over whose methods we have no control. It is the user’s responsibility to
determine suitability for the user’s purpose of any production methods mentioned
herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
and use thereof. In light of the foregoing,
Henkel Corporation specifically
disclaims all warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from sale or use
of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
including lost profits.
The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
domination of patents owned by others or as a license under any Henkel
Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
repetitive use, using this data as a guide. This product may be covered by one or
more United States or foreign patents or patent applications.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks of
Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark
registered in the U.S. Patent and Trademark Office
Reference 0.1
Americas
+1.800.347.4572
Europe
+31.35.5380684
For the most direct access to local sales and technical support visit: www.bergquistcompany.com
Asia
+852.2690.9296
京公网安备 11010802033920号
EEWORLD
