EEWORLDEEWORLDEEWORLD

Part Number

Search

MAX20327EVKIT#

Description
Switch IC development tool Evkit for 12V Capable, Low-RON, Beyond-the-RailsTM DPDT Analog Switch
CategoryEmbedded solution    Engineering tools    Analog and digital IC development tools    Switch IC development tools   
File Size826KB,10 Pages
ManufacturerMaxim
Websitehttps://www.maximintegrated.com/en.html
Environmental Compliance
Download Datasheet Parametric View All

MAX20327EVKIT# Overview

Switch IC development tool Evkit for 12V Capable, Low-RON, Beyond-the-RailsTM DPDT Analog Switch

MAX20327EVKIT# Parametric

Parameter NameAttribute value
MakerMaxim
Product CategorySwitch IC Development Tools
Shipping restrictionsMouser does not currently sell this product.
productEvaluation Kits
typeAnalog Switches
Tools for assessmentMAX20327
seriesMAX20327
Working power voltage1.6 V to 5.5 V
Factory packaging quantity1
Click
here
for production status of specific part numbers.
MAX20327 Evaluation Kit
Evaluate: MAX20327
General Description
The MAX20327 evaluation kit (EV kit) is a fully assembled
and tested circuit board that demonstrates the functionality
of the MAX20327 double-pole, double-throw (DPDT)
analog switches in a 9-bump wafer-level package (WLP).
The EV kits features enable evaluation of the analog
switches through audio jack inputs and outputs, as well
as SMA connectors for AC characteristic evaluation. Input
power to the EV kits is provided by a Micro-USB, type-B
connector or an external power supply.
Quick Start
Required Equipment
MAX20327 EV kit
USB power supply or 1.6V to 5.5V power supply
Audio source (e.g., MP3 player, computer, etc.)
External speakers or headphones with 3.5mm audio
jack
Procedure
Features
Proven PCB Layout
• Decreased Evaluation Time
Fully Assembled and Tested
SMA and 3.5mm Audio Jack Connectors
• Directly Evaluate AC Characteristics Through SMA
Connectors
• Quickly Evaluate Audio Performance with 3.5mm
Audio Jack Connectors
USB 5V Power with On-Board Adjustable LDO
The EV kits are fully assembled and tested. Follow the
steps below to verify board operation and begin evaluation:
1) If using a USB power supply to power the board
through the Micro-USB connector (J1), verify that a
shunt is installed shorting pins 3-4 on jumper JU2.
This powers the devices from the output of the on-
board LDO. To adjust the LDO output voltage, connect
a voltmeter at test point T3 and turn the screw on the
potentiometer (R3) until reaching the desired value. To
use the raw bus voltage as the power supply for the
devices, place the shunt so that it is shorting pins 5-6
on JU2.
2) If an external power supply is used, apply the power
at test point T2 and use the shunt to short pins 1-2 on
JU2 to provide power to the parts from the external
supply.
Ordering Information
appears at end of data sheet.
3) Verify that jumper JU1 has a shunt installed shorting
pins 2-3 and that jumper JU4 has a shunt installed
shorting pins 2-3. Installing the shunts in these locations
provides power from the source to the V
CC
pin of the
devices.
4) Verify that jumper JU3 has a shunt installed shorting
pins 1-2. This shorts the control bit (CB) on the devices
to GND, electrically connecting NC1 to COM1 and
NC2 to COM2.
5) Connect an audio source to the normally closed audio
jack (P2), using the male-to-male 3.5mm audio cable
included with the EV kit.
319-100231; Rev 0; 8/18
Model-based design subverts traditional FPGA development methods!
Recently, I compared the comprehensive results of handwritten HDL code (21 lines); code generated by DSP Builder (>200 lines); and code generated by Simulink HDL Coder (>200 lines) on the same experim...
平湖秋月 FPGA/CPLD
LED flashing drive circuit diagram analysis
I recently drew a fast-response LED flashing drive circuit. After many changes, I think the circuit is relatively reasonable, but it still crashes after a long time of simulation. I hope you can help ...
Ansami Analog electronics
[Help] Can I use shift instructions on IAR? ? I can't use it!!
Shift variable a to the left: a>>3;shift right abut I can't use it on IAR. The system warns that it doesn't work. Is there any alternative? Will using multiplication and division affect the speed? ?...
raiderchina Microcontroller MCU
Future Development of Industrial Ethernet
There is still a long way to go to achieve a unified and operable industrial Ethernet.From the above discussion, it is not difficult to see that large automation system companies use industrial Ethern...
wdxyx Industrial Control Electronics
【labview】Design Pattern - Producer Consumer
Design Pattern - Producer Consumer...
安_然 Test/Measurement
ROS controls the car to run programming
[p=26, null, left][color=rgb(79, 79, 79)][font="]1、 roscore[/font][/color][/p][p=26, null, left][color=rgb(79, 79, 79)][font="]2、 sudo chmod a+rw /dev/ttyACM0[/font][/color][/p][p=26, null, left][colo...
fiveFeng Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1464  560  2592  1159  2837  30  12  53  24  58 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号