ACPL-M60L
Small Outline, 5 Leads, High CMR, High Speed,
Logic Gate Optocouplers
Data Sheet
Description
The ACPL-M60L is an optically coupled gate that com-
bines a GaAsP light emitting diode and an integrated
high gain photo detector. The output of the detector
IC is an open collector Schottky-clamped transistor. The
internal shield provides a guaranteed common mode
transient immunity specification of 15 kV/µs at 3.3V op-
eration.
This unique design provides maximum AC and DC circuit
isolation while achieving LVTTL/LVCMOS compatibility.
The optocoupler AC and DC operational parameters are
guaranteed from –40˚C to +85˚C, allowing trouble-free
system performance.
These optocouplers are suitable for high speed logic
interfacing, input/output buffering, as line receivers in
environments that conventional line receivers cannot
tolerate and are recommended for use in extremely high
ground or induced noise environments.
Features
•
Dual Voltage Operation (3.3V/5V)
•
Low power consumption
•
15 kV/µs minimum Common Mode Rejection (CMR)
at V
CM
= 1000 V (3.3V operating voltage)
•
High speed: 15 MBd typical
•
LVTTL/LVCMOS compatible
•
Low input current capability: 5 mA
•
Guaranteed AC and DC performance over tempera-
ture: –40˚C to +85˚C
•
Safety approvals; UL, CSA, IEC/EN/DIN EN 60747-5-2
•
Surface mountable
•
Very small, low profile JEDEC Registered package
outline
Applications
•
Isolated line receiver
•
Computer-peripheral interfaces
•
Microprocessor system interfaces
•
Digital isolation for A/D, D/A conversion
•
Switching power supply
•
Instrument input/output isolation
•
Ground loop elimination
•
Pulse transformer replacement
•
Field buses
Functional Diagram
ANODE 1
6 V
CC
5 V
O
CATHODE 3
4 GND
CAUTION:
It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Ordering Information
ACPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577 and is approved under CSA Component Ac-
ceptance Notice #5, File CA 88324.
Option
RoHS
Part Number
Compliant
Package
Surface Mount
Tape & Reel
IEC/EN/DIN EN 60747-5-2
Quantity
ACPL-M60L
-000E
-500E
SO-5
X
X
X
100 per tube
1500 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry. Combination of Option 020 and Option 060 is not available.
Example 1:
ACPL-M60L-500E to order product of Surface Mount SO-5 in Tape and Reel packaging with RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Schematic
+
1
I
O
5
I
F
I
CC
6
V
CC
V
O
–
3
ACPL-M60L SHIELD
USE OF A 0.1 µF BYPASS CAPACITOR
MUST BE CONNECTED BETWEEN PINS
6 AND 4 (SEE NOTE 1).
4
GND
TRUTH TABLE
(POSITIVE LOGIC)
OUTPUT
LED
L
ON
H
OFF
2
Package Outline Drawing
4.4 ± 0.1
(0.173 ± 0.004)
M60L
XXX
ANODE
7.0 ± 0.2
(0.276 ± 0.008)
CATHODE
1
6
5
V
CC
V
OUT
GND
3
4
0.4 ± 0.05
(0.016 ± 0.002)
3.6 ± 0.1*
(0.142 ± 0.004)
2.5 ± 0.1
(0.098 ± 0.004)
0.102 ± 0.102
(0.004 ± 0.004)
0.216 ± 0.038
(0.0085 ± 0.0015)
7 MAX.
1.27 BSC
(0.050)
0.71 MIN.
(0.028)
MAX. LEAD COPLANARITY
= 0.102 (0.004)
DIMENSIONS IN MILLIMETERS (INCHES)
* MAXIMUM MOLD FLASH ON EACH SIDE IS 0.15 mm (0.006)
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
Land Pattern
4.4
(0.17)
1.3
(0.05)
2.5
(0.10)
2.0
(0.080)
8.27
(0.325)
0.64
(0.025)
3
Solder Reflow Temperature Profile
300
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
PEAK
TEMP.
245°C
PEAK
TEMP.
240°C
TEMPERATURE (°C)
200
160°C
150°C
140°C
PEAK
TEMP.
230°C
2.5°C ± 0.5°C/SEC.
30
SEC.
3°C + 1°C/–0.5°C
30
SEC.
SOLDERING
TIME
200°C
100
PREHEATING TIME
150°C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
0
50
100
150
200
250
TIME (SECONDS)
Note: Non-halide flux should be used
Recommended PB-Free IR Profile
t
p
T
p
T
L
TEMPERATURE
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
260 +0/-5 °C
217 °C
RAMP-UP
3 °C/SEC. MAX.
150 - 200 °C
T
smax
T
smin
RAMP-DOWN
6 °C/SEC. MAX.
t
s
PREHEAT
60 to 180 SEC.
25
t
L
60 to 150 SEC.
t 25 °C to PEAK
TIME
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
T
smax
= 200 °C, T
smin
= 150 °C
Note: Non-halide flux should be used
4
Insulation and Safety Related Specifications
Parameter
Minimum External Air Gap
(Clearance)
Minimum External Tracking Path
(Creepage)
Minimum Internal Plastic Gap
(Clearance)
Tracking Resistance
Isolation Group (per DIN VDE 0109)
CTI
Symbol
L (I01)
L (I02)
Value
≥5
≥5
0.08
175
IIIa
Units
mm
mm
mm
V
Conditions
Measured from input terminals to output
terminals
Measured from input terminals to output
terminals
Through insulation distance, conductor to
conductor
DIN IEC 112/VDE 0303 Part 1
Material Group DIN VDE 0109
Absolute Maximum Ratings (No Derating Required up to 85˚C)
Parameter
Storage Temperature
Operating Temperature†
Average Forward Input Current
Reverse Input Voltage
Input Power Dissipation
Supply Voltage (1 minute maximum)
Output Collector Current
Output Collector Voltage
Output Collector Power Dissipation
Solder Reflow Temperature Profile
Symbol
T
S
T
A
I
F
V
R
P
I
V
CC
I
O
V
O
P
O
Min.
–55
–40
Max.
125
85
20
5
40
7
50
7
85
Units
˚C
˚C
mA
V
mW
V
mA
V
mW
Note
1
See Package Outline Drawings section
Recommended Operating Conditions
Parameter
Input Current, Low Level
Input Current, High Level
[1]
Power Supply Voltage
Operating Temperature
Fan Out (at R
L
= 1 kΩ)
[1]
Output Pull-up Resistor
Symbol
I
FL
*
I
FH
**
V
CC
T
A
N
R
L
Min.
0
5
2.7
4.5
–40
Max.
250
15
3.6
5.5
85
5
Units
µA
mA
V
V
˚C
TTL Loads
Ω
330
4k
*The off condition can also be guaranteed by ensuring that V
FL
≤ 0.8 volts.
**The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be
used for best performance and to permit at least a 20% LED degradation guardband.
5
京公网安备 11010802033920号
EEWORLD
