HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH
®
PRODUCTS
HIGH-SPEED CMOS 10-BIT
BUS SWITCH WITH
FLOW-THROUGH PINOUT
•
•
•
•
•
IDTQS3861
FEATURES:
DESCRIPTION:
Enhanced N channel FET with no inherent diode to Vcc
5Ω bidirectional switches connect inputs to outputs
Ω
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
Available in QSOP and TSSOP packages
The QS3861 provides a set of ten high-speed CMOS TTL-compatible
bus switches. The low ON resistance (5Ω) of the QS3861 allows inputs to
be connected without adding propagation delay and without generating
additional ground bounce noise. The Bus Enable (BE) signal turns the
switches on.
The QS3861 is characterized for operation at -40°C to +85°C.
APPLICATIONS:
•
•
•
•
•
•
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Power Conservation
Capacitance reduction and isloation
Bus Isolation
Clock Gating
FUNCTIONAL BLOCK DIAGRAM
A
0
B
0
A
9
B
9
BE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
c 2013 Integrated Device Technology, Inc.
JANUARY 2013
1
DSC-5767/6
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
NC
A
0
A
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
GND
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
Vcc
BE
B
0
B
1
B
2
B
3
B
4
B
5
B
6
B
7
B
8
B
9
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
TERM
(2)
V
TERM
(3)
V
TERM
(3)
V
AC
I
OUT
P
MAX
T
STG
Description
Supply Voltage to Ground
DC Switch Voltage V
S
DC Input Voltage V
IN
AC Input Voltage (pulse width
≤20ns)
DC Output Current
Maximum Power Dissipation
Storage Temperature
Max
–0.5 to +7
–0.5 to +7
–0.5 to +7
–3
120
0.5
–65 to +150
Unit
V
V
V
V
mA
W
°C
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
CAPACITANCE
(T
A
= +25°C, f = 1MHz, V
IN
= 0V, V
OUT
= 0V)
Pins
Control Inputs
Quickswitch Channels (Switch OFF)
Typ.
3
5
Max.
(1)
5
7
Unit
pF
pF
QSOP/ TSSOP
TOP VIEW
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
A
0
- A
9
B
0
- B
9
BE
Bus A
Bus B
Bus Switch Enable
Description
FUNCTION TABLE
(1)
BE
H
L
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedance
A
0
- A
9
Z
B
0
- B
9
Function
Disconnect
Connect
2
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 5V ± 5%
Symbol
V
IH
V
IL
I
IN
I
OZ
R
ON
V
P
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Switch ON Resistance
Pass Voltage
(2)
Test Conditions
Guaranteed Logic HIGH for Control Pins
Guaranteed Logic LOW for Control Pins
0V
≤
V
IN
≤
V
CC
0V
≤
V
OUT
≤
V
CC
, Switches OFF
V
CC
= Min., V
IN
= 0V, I
ON
= 30mA
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
V
IN
= V
CC
= 5V, I
OUT
= -5μA
Min.
2
—
—
—
—
—
3.7
Typ.
(1)
Max.
—
—
±0.01
±0.01
5
10
4
—
0.8
±1
±1
7
15
4.2
V
Unit
V
V
μA
μA
Ω
NOTES:
1. Typical values are at V
CC
= 5V and T
A
= 25°C.
2. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 5V
16
14
R
ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
V
IN
(Volts)
2.0
2.5
3.0
3.5
3
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
ΔI
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current per Input HIGH
(3)
Dynamic Power Supply Current per MHz
(4)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3.4V, f = 0
V
CC
= Max., A and B Pins Open,
BE
Input Toggling @ 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Typical values are at V
CC
= 5V and T
A
= 25°C.
3. Per TTL-driven input (V
IN
= 3.4V, control inputs only). A and B pins do not contribute to
ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
Typ.
(2)
0.2
⎯
⎯
Max.
3
2.5
0.25
Unit
μA
mA
mA/MHz
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C, V
CC
= 5V ± 5%
C
LOAD
= 50pF, R
LOAD
= 500Ω unless otherwise noted.
Symbol
t
PLH
t
PHL
t
PZL
t
PZH
t
PLZ
t
PHZ
Parameter
Data Propagation Delay
(2)
A to B, B to A
Switch Turn-On Delay
BE
to A or B
Switch Turn-Off Delay
(2)
BE
to A or B
Min
.
(1)
⎯
1.5
1.5
Typ.
⎯
⎯
⎯
Max.
0.25
(3)
6.5
5.5
Unit
ns
ns
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4
IDTQS3861
HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Blank
8
Tube or Tray
Tape and Reel
QG
PAG
Quarter Size Outline Package - QSOP Green
Thin Shrink Small Outline Package - TSSOP Green
3861
High Speed CMOS 10-Bit Bus Switch
with Flow-Through Pinout
Datasheet Document History
01/25/13
Pg. 1, 5
Updated the Ordering Information by removing non green package version, the “IDT” notation and
[font=宋体] After a company recruits new employees, there will be an induction training. The content of the new employee induction training is saved in the format of PDF files, but when explaining to em...
I use the stc51 microcontroller to control the isd1720 voice chip. The pdf says that data is sent and received simultaneously, but doesn't it mean that the command must be sent before the return value...
Protocol stack version information used: ZigBee2006\ZStack-1.4.3-1.2.1
Record a few questions:
*********************************** 1. The startup mode options of the relevant equipment: (to be improve...
I have a question! The 3D STP file of the PCB exported by AD software has all the components, but the board is transparent. Has anyone encountered this situation? How to solve it?...
In order to achieve USB communication, a universal USB interface chip needs to be selected. Considering the price, whether the information is rich and whether it is convenient to buy, Dream Travel ini...
A simple circuit with a controlled source refers to a circuit with a controlled source and an independent source. After the circuit equivalent transformation, it can be simplified to a circuit with on...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Investment in
the
medical device
industry has been on the rise in recent years. In the past two years, venture capital for medical devices has almost doubled, reaching $4 billion in 2007. Fr...[Details]
introduction
MEMS is a high-tech that has flourished on the basis of integrated circuit production technology and dedicated micro-electromechanical processing methods. Pressure sensors develop...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
Recently, news came from the certification department that the photovoltaic grid-connected inverter of Samil New Energy Co., Ltd. (hereinafter referred to as "Samil New Energy") has once again obta...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
The most important components of new energy electric vehicles are power batteries, electric motors and energy conversion control systems. The power battery must achieve high performance such as fas...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
