This product specification is applied to Chip Monolithic Ceramic Capacitor used for General Electronic equipment.Do not use these products in any automotive power
train or safety equipment including battery chargers for electric vehicles and plugin hybrids.
2.MURATA Part NO. System
(Ex.)
GRM
21
(1)L/W
Dimensions
A
(2)T
Dimensions
5C
(3)Temperature
Characteristics
2J
(4)Rated
Voltage
680
(5)Nominal
Capacitance
J
(6)Capacitance
Tolerance
WA1
(7)Murata’s Control
Code
D
(8)Packaging Code
3. Type & Dimensions
(1)-1 L
2.0±0.2
(1)-2 W
1.25±0.2
(2) T
1.0+0/-0.3
e
0.3 min.
(Unit:mm)
g
0.7 min.
4.Rated value
(3) Temperature Characteristics
(Public STD Code):C0G(EIA)
Temp. coeff
Temp. Range
or Cap. Change
(Ref.Temp.)
(4)
Rated
Voltage
(6)
(5) Nominal
Capacitance
Capacitance
Tolerance
Specifications and Test
Methods
(Operating
Temp. Range)
0±30 ppm/°C
・Soldering
Method
Flow / Reflow
25 to 125 °C
(25 °C)
DC 630 V
68 pF
±5 %
-55 to 125 °C
5.Package
mark
D
J
(8) Packaging
f180mm
Reel
PAPER
f330mm
Reel
PAPER
Packaging Unit
4000 pcs./Reel
10000 pcs./Reel
Product specifications in this catalog are as of Sep.14,2016,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
GRM21A5C2J680JWA1-01
1
■
Specifications and Test Methods
No
1
2
3
Appearance
Dimension
Voltage proof
Item
Specification
No defects or abnormalities.
Within the specified dimensions.
No defects or abnormalities.
Visual inspection.
Using calipers and micrometers.
Measurement Point :
Test Voltage
:
Between the terminations
200% of the rated voltage
(Rated
voltage:DC200V,DC250V)
150% of the rated voltage
(Rated
voltage:DC500V,DC630V)
130% of the rated voltage
(Rated
voltage:DC1kV,DC2kV)
(Rated voltage(7U only):DC3.15kV)
Applied Time
:
1 to 5 s
Charge/discharge current : 50mA max.
4
Insulation Resistance(I.R.)
More than 10000MΩ or 100MΩ・μF
(Whichever is smaller)
Measurement Point
:
Measurement Voltage :
Between the terminations
DC200+/-20V(Rated voltage:DC200V)
DC250+/-25V(Rated voltage:DC250V)
DC500+/-50V
(Rated voltage:DC500V,DC630V,DC1kV,DC2kV)
(Rated voltage(7U only):DC3.15kV)
Charging Time
:
60+/-5s
Measurement Temperature: Room Temperature
5
Capacitance
Shown in Rated value.
Measurement Temperature: Room Temperature
Test Method
(Ref. Standard:JIS C 5101, IEC60384）
6
Q
1000 min.
Capacitance
C＜1000pF
C≥1000pF
Frequency
1.0+/-0.1Mhz
1.0+/-0.1khz
Voltage
AC 0.5 to 5.0V(r.m.s)
AC 1.0+/-0.2V(r.m.s)
7
Temperature
Characteristics
of Capacitance
5C:0+/-30 ppm/°C
0+30/-72 ppm/°C
7U：-750+/-120 ppm/°C
(Temp.Range:+25 to +125°C)
(Temp.Range:-55 to +25°C)
(Temp.Range:+25 to +125℃)
The capacitance change should be measured after 5 min.
at each specified temp. stage.
Capacitance value as a reference is the value in step 3.
-750+120/-347
ppm/°C (Temp.Range:-55 to +25℃)
Step
1
2
3
4
5
Temperature(C)
Reference Temp.+/-2
Min.Operating Temp. +/-3
Reference Temp. +/-2
Max.Operating Temp. +/-3
Reference Temp. +/-2
Ste
Temp
8
Vibration
Appearance
Capacitance
Q
No defects or abnormalities.
Within the specified initial value.
Within the specified initial value.
Solder the capacitor on the test substrate A shown in "Complement of Test
method”.
Kind of Vibration
Total amplitude
:
:
A simple harmonic motion
10Hz to 55Hz to 10Hz (1min)
1.5mm
This motion should be applied for a period of 2h in each 3 mutually
perpendicular directions(total of 6h).
9
Solderability
95% of the terminations is to be soldered evenly and
continuously.
Test Method
Preheat
Solder
Solder Temp.
Immersion time
:
:
:
:
:
Solder bath method
Solution of rosin ethanol 25(wt)%
80℃ to 120℃ for 10s to 30s
Sn-3.0Ag-0.5Cu (Lead Free Solder)
245+/-5℃
2+/-0.5s
25+/-2.5mm/s.
Solder bath method
Sn-3.0Ag-0.5Cu (Lead Free Solder)
260+/-5℃
:
:
10+/-1s
25+/-2.5mm/s.
24+/-2h at room condition*.
GRM31 size max.: 120℃ to 150℃ for 1 min
GRM32 size min. : 100℃ to 120℃ for 1 min
and 170℃ to 200℃ for 1 min
Flux :
Immersing in speed :
10 Resistance
to
Soldering
Heat
Capacitance
Change
Q
I.R.
Within the specified initial value.
Within the specified initial value.
Within +/-2.5% or +/-2.5pF (Whichever is larger)
Appearance
No defects or abnormalities.
Test Method
Solder
Solder Temp.
Immersion time
Exposure Time
Preheat
Voltage proof No defects.
:
:
:
Immersing in speed :
:
*Room Condition : Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa
JEMCGS-04233B
2
No
Item
Specification
No removal of the terminations or other defect
should occur.
Test Method
(Ref. Standard:JIS C 5101, IEC60384）
Solder the capacitor on the test substrate A shown in "Complement of Test
method”.
11 Adhesive Strength
of Termination
10N, 10+/-1s
Applied Direction : In parallel with the test substrate and vertical with the
capacitor side.
12 Substrate
Bending test
No defects or abnormalities.
Solder the capacitor on the test substrate B shown in "Complement of Test
method”.
Then apply the force in the direction shown in “Test Method of Substrate
Bending test” of “Complement of Test method”.
Flexure
Holding Time
Soldering Method
13 Temperature
Sudden Change
Capacitance
Change
Step
1
Temp.(C)
Min.Operating Temp.+0/-3
Room Temp
Max.Operating Temp.+3/-0
Room Temp
:
:
:
1mm
5+/-1s
Reflow soldering
Appearance
No defects or abnormalities.
Fix the capacitor to the supporting Test substrate A (glass epoxy board)
shown in “Complement of Test method”.
Perform the 5 cycles according to the four heat treatments
Within +/-2.5% or +/-2.5pF (Whichever is larger)
shown in the following table.
Time
(min)
30+/-3
2 to 3
30+/-3
2 to 3
Q
500 min.
2
3
I.R.
Within the specified initial value.
4
Exposure Time
Voltage proof No defects.
:
24+/-2h at room condition*.
14
Humidity
(Steady state)
Appearance
Capacitance
Change
Q
I.R.
No defects or abnormalities.
Within +/-5% or +/-5pF (Whichever is larger)
Fix the capacitor to the supporting Test substrate A (glass epoxy board)
shown in “Complement of Test method”.
Test Temperature
Test Humidity
Test Time
:
:
:
:
40+/-2℃
90% to 95%RH
500+24/-0h
24+/-2h at room condition*.
350 min.
More than 1000MΩ or 10MΩ・μF
(Whichever is smaller)
Exposure Time
Voltage proof No defects.
15 Durability
Appearance
No defects or abnormalities.
Fix the capacitor to the supporting Test substrate A (glass epoxy board)
shown in “Complement of Test method”.
Test Temperature
:
:
:
Max. Operating Temp. +/-3℃
1000+48/-0h
150% of the rated voltage
(Rated
voltage:DC200V,DC250V)
120% of the rated voltage
Capacitance
Change
Within +/-3% or +/-3pF (Whichever is larger)
Test Time
Applied Voltage
Q
350 min.
(Rated
voltage:DC500V,DC630V,DC1kV,DC2kV)
(Rated
voltage(7U only):DC3.15kV)
I.R.
More than 1000MΩ or 10MΩ・μF
(Whichever is smaller)
Charge/discharge current : 50mA max.
Exposure Time
:
24+/-2h at room condition*.
Voltage proof No defects.
*Room Condition : Temperature:15 to 35°C, Relative humidity:45 to 75%, Atmosphere pressure:86 to 106kPa
JEMCGS-04233B
3
Complement of Test Method
1.Test substrate
The test substrate should be Substrate A or Substrate B as described in “Specifications and Test methods”.
The specimen should be soldered by the conditions as described below.
Soldering Method : Reflow soldering
Solder : Sn-3.0Ag-0.5Cu
(1) Test Substrate A
½Land
Dimensions
Chip Capacitor
Type
Land
b
½Material
a
Solder Resist
GRM18
GRM21
GRM31
GRM32
GRM42
GRM43
GRM52
GRM55
a
1.0
1.2
2.2
2.2
3.5
3.5
4.5
4.5
Dimension (mm)
b
3.0
4.0
5.0
5.0
7.0
7.0
8.0
8.0
c
1.2
1.65
2.0
2.9
2.4
3.7
3.2
5.6
c
: Glass Epoxy Board
½Thickness
: 1.6mm
½Thickness
of copper foil : 0.035mm
(1) Test Substrate B
a
Type
GRM18
GRM21
GRM31
GRM32
GRM42
GRM43
GRM52
GRM55
(unit : mm)
d
c
(f4.5)
b
100
1.6
Copper foil
Solder resist
½Material
: Glass Epoxy Board
½Thickness
of copper foil : 0.035mm
2. Test Method of Substrate Bending test
a) Support state
(b) Test state
a
1.0
1.2
2.2
2.2
3.5
3.5
4.5
4.5
Dimension of pettern (mm)
b
c
3.0
1.2
4.0
1.65
5.0
2.0
5.0
2.9
7.0
2.4
7.0
3.7
8.0
3.2
8.0
5.6
d
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
40
Test
Substrate
B
20
50 min.
b
Test Substrate B
a
Capacitor
Support stand(f5)
45+/-2
45+/-2
Test stand
Support stand
Pressure stick
(unit : mm)
a:+/-2 gap between support stand center and test stand
·Material of Test stand and pressure stick
b:+/-5
gap between support stand center and test stand center
The
material shoud be a metal where a remarkable transformation and the distortion are not caused even if it is pressurized.
·Pressurizing speed
The
pressurizing speed is pressurized at the speed of about 1mm/s until the flexure reaches a regulated value.
Pressure stick
F
Capacitor
R5
L
45
45
Support
Support
stand
JEMCGS-04233B
4
Package
(1) Appearance of taping
(a) Paper Tape
Bottom Tape (Thickness: Around 50m) is attached below Base Tape with sprocket and put Top Tape
(Thickness: Around 50m) on capacitor.
(b) Plastic Tape
Cover Tape (Thickness: Around 60m) is put on capacitor on Base Tape (Blister carrier Tape).
(c) The sprocket holes are to the right as the Tape is pulled toward the user.
(2) Packed chips
Capacitor
(3) Dimensions of Tape
(a) Type A (Dimensions of chip : Apply to 1.6x0.8 , 2.0x1.25 , 3.2x1.6 , 3.2x2.5)
1.75±0.1
f
1.5+0.1/-0
4.0±0.1
4.0±0.1
(Plastic Tape)
0.25±0.1
3.5±0.05
(Paper Tape)
2.0±0.05
8.0±0.3
B
A
2.5max.
1.1max.
(Unit : mm)
Dimensions of chip
[L×W]
1.6×0.8
2.0×1.25
3.2×1.6
3.2×2.5
A*
1.05
1.45
2.0
2.9
B*
1.85
2.25
3.6
3.6
Dimensions
of A,B : Nominal value
(b) Type B (Dimensions of chip : Apply to 4.5x2.0)
Virtual drum set Use 3DMAX to draw a drumstick Export the obj file and add it to the Android project Now you can control the posture of the 3D body The next step is to associate the sensor data with t...
Dear experts, I have a few questions to ask when initializing the RAMECC of the TMS570LS3137 chip: 1. In the code automatically generated by the HAL Code generator, in the _c_int00() function, why is ...
[p=35, null, left][color=#555555][font="][size=15px]1. F28035_Device.h[/size][/font][/color][/p][p=35, null, left][color=#555555][font="][size=15px]This file is the definition of commonly used macros,...
1. Several nouns
ABI:
The specifications that an executable file must follow in order to run in a specific execution environment;
Separately generated relocatabl...[Details]
On August 24th, Tesla CEO Elon
Musk
revealed information about the upcoming FSD V14, claiming it will outperform human drivers. Tesla FSD lead Ashok stated last year that FSD version 12.5, ...[Details]
Whether it is an electric car or an ordinary fuel car, for the vast majority of car buyers, the final cost of use is what they care about most. For fuel cars, how to save fuel is what drivers care ...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
1. Ease of Use: The HMI module should be designed to be simple and clear, allowing users to easily operate and configure the energy storage device.
2. Ease of Maintenance: The HMI module should...[Details]
On August 22, according to CNBC's report today, the National Highway Traffic Safety Administration (NHTSA) is launching an investigation into Tesla, and the latter is questioned whether it has fail...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
According to Nikkei, a survey found that global electric vehicle battery supply is expected to reach more than three times the required quantity due to
cooling
demand for electric vehicles,...[Details]
Tiantai Robot's official Weibo account announced on the evening of August 20 that Tiantai Robot Co., Ltd., together with strategic partners including Shandong Future Robot Technology Co., Ltd., Sha...[Details]
To improve the lateral active safety of intelligent connected vehicles, the identification and definition of unexpected functional safety scenarios for the EPS (Electronic Steering System) ...[Details]
A pure sine wave inverter has a good output waveform with very low distortion, and its output waveform is essentially the same as the AC waveform of the mains power grid. In fact, the AC power prov...[Details]
There are many motors that can use thyristor speed control, and they can be used in almost all industries. Various types of motors, such as fans, pumps, AC motors, DC motors, torque motors, single-...[Details]
Civilian internal combustion engines operate in the range of approximately 1000-4000 rpm. This results in the engine's kinetic energy being ineffective at low or high rpm, making starting difficult...[Details]
Introduction: In digital circuit calculations, there is no concept of decimal points. You know where the decimal is, but the circuit does not know where the decimal point is. Therefore, you need to...[Details]
I recently read an article in the Wall Street Journal titled "We need the right to repair our gadgets" (reference original article: ). The author was very angry about the phenomenon of "planned obs...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
