of "●Precautions" for more information on the minimum applicable
load.
Ratings
Model
D2S-10
models
D2S-5
models
D2S-01
models
Item
Rated voltage
250 VAC
125 VAC
250 VAC
125 VAC
30 VDC
Resistive load
10.1 A
5A
3A
0.1 A
0.1 A
Characteristics
Item
Permissible operating speed
Permissible
operating
frequency
Mechanical
Electrical
Model
D2S-10 models
D2S-5 models
D2S-01 models
0.1 mm to 1 m/s (for pin plunger models)
400 operations/min
60 operations/min
100 MΩ min. (at 500 VDC with insulation tester)
OF 1.47 N models
OF 0.49 N models
-
30mΩ max.
50 mΩ max.
1,000 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
10 to 55 Hz, 1.5 mm double amplitude
OF 1.47 N models
OF 0.49 N models
OF 1.47 N models
OF 0.49 models
1,000 m/s
2
{approx. 100G} max.
500 m/s
2
{approx. 50G} max.
300 m/s
2
{approx. 30G} max.
200 m/s
2
{approx. 20G} max.
10,000,000 operations min.
(60 operations/min)
50,000 operations min.
(30 operations/min)
30,000,000 operations min.
(60 operations/min)
200,000 operations min.
(30 operations/min)
IEC IP40
-25°C to
+85°C
(at ambient humidity of 60% max.)
(with no icing or condensation)
85% max. (for
+5°C
to
+35°C)
Approx. 1.6 g (pin plunger models)
50 mΩ max.
100 mΩ max.
Insulation resistance
Contact resistance
(initial value)
Note. The above rating values apply under the
following test conditions.
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%
(3) Operating frequency: 30 operations/min
Between terminals of the same
polarity
Dielectric
strength * 1
Between current-carrying metal
parts and ground
Between each terminals and
non-current-carrying metal parts
Vibration
resistance * 2
Malfunction
Durability
Shock
resistance
Malfunction * 2
Mechanical
Durability * 3
Electrical
Approved Safety
Standards
The items shown in the "List
of Models"
are not standard approved models.
Consult your OMRON sales
representative for specific models with
standard approvals.
UL (UL1054)/CSA(CSA C22.2 No.55)
Rated
voltage
Model
D2S-10
-
10.1 A
-
D2S-5
5A
3A
-
D2S-01
0.1 A
-
0.1 A
Degree of protection
Ambient operating temperature
Ambient operating humidity
Weight
125 VAC
250 V
30 VDC
Note. The data given above are initial values.
*1. The values for dielectric strength shown are for models with a Separator (refer to "Micro
Switch
Common Accessories").
*2. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel
Position value for lever.
Close or open circuit of the contact is 1ms max.
*3. For testing conditions, consult your OMRON sales representative.
2
D2S
Terminals/Appearances
(Unit: mm)
●Solder
terminals
3.3
±0.1
2
7.3
8.8
±0.2
9.5
±0.1
16.1
±0.2
1.6
3.2
0.5
6.4
±0.2
5.15
1.85
8.8
±0.2
9.5
±0.1
16.1
±0.2
0.8
1.2
6.4
±0.2
0.5
1.3
Subminiature Basic Switch
Mounting Holes
(Unit: mm)
2-2.4 dia. mounting holes or
M2.3 screw holes
●Self-clinching
PCB terminals
3.3
±0.1
2
1.8
±0.1
3.9
9.5
±0.1
3-1.6 dia.holes
5.15
1.85
<PCB Mounting Dimensions (Reference)>
3-1.35
1.5 dia.
D
2
S
8.8
±0.2
16.1
±0.2
PCB's thickness t
1.6mm
Dimensions
(Unit: mm)
and Operating Characteristics
The following figures show models with self-clinching PCB terminals. For the solder terminals, refer to "Terminals/Appearances".
The
@
is replaced with the code for the terminal that you need. See the "List
of Models"
for available combinations of models.
●Pin
plunger
D2S-10@
D2S-5@
D2S-5-F@
D2S-01@
D2S-01-F@
5.3
A
2.35
±0.05
dia.
7.5
±0.1
1.8
2.35
±0.05
dia.
PT
3.6
Model
Operating
characteristics
1.8
±0.1
7
2
7.7
OP
D2S-10@
D2S-5@
D2S-01@
D2S-5-F@
D2S-01-F@
3.3
±0.1
3.9
Operating Force
Releasing Force
OF
RF
Max. 1.47 N {150 gf} 0.49 N {50 gf}
Min. 0.25 N {25 gf} 0.04 N {4 gf}
0.7 mm
0.4 mm
0.1 mm
8.4±0.25 mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
Pretravel
PT Max.
Overtravel
OT Min.
Movement Differential MD Max.
Operating Position
OP
19.8
±0.2
●Hinge
lever
D2S-10L@
D2S-5L@
D2S-5L-F@
D2S-01L@
D2S-01L-F@
t 0.3 *
14.5
A
2.35
±0.05
dia.
3.6
Model
FP
2.35
±0.05
dia.
7
2
7.7
OP
1.8
±0.1
Operating
characteristics
Operating Force
Releasing Force
OF
RF
D2S-10L@
D2S-5L@
D2S-01L@
D2S-5L-F@
D2S-01L-F@
0.18 N {18 gf}
0.02 N {2 gf}
3.3
±0.1
3.9
Max. 0.49 N {50 gf}
Min. 0.06 N {6 gf}
Overtravel
OT Min.
Movement Differential MD Max.
0.5
1.3
1.0 mm
0.8 mm
13.6 mm
9.4±0.8mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
* Stainless-steel lever
6.4
±0.2
Free Position
Operating Position
FP Max.
OP
19.8
±0.2
●Simulated
roller lever
D2S-10L13@
D2S-5L13@
D2S-5L13-F@
D2S-01L13@
D2S-01L13-F@
15.8
t 0.3 *
A
R1.3
3.6
2.35
±0.05
dia.
FP
Operating
characteristics
Operating Force
Releasing Force
Model D2S-10L13@
D2S-5L13@
D2S-01L13@
OF Max.
RF Min.
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L13-F@
D2S-01L13-F@
0.18 N {18 gf}
0.02 N {2 gf}
2.35
±0.05
dia.
OP
7
2
7.7
3.3
±0.1
3.9
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
1.8
±0.1
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
15.5 mm
11.4±0.8 mm
0.5
1.3
*Stainless-steel lever
6.4
±0.2
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
3
D2S
●Hinge
roller lever
D2S-10L2@
D2S-5L2@
D2S-5L2-F@
D2S-01L2@
D2S-01L2-F@
14.5
t=0.3 *1
2.35
±0.05
dia.
FP
OP
2.35
±0.05
dia.
7
2
7.7
3.3
±0.1
3.9
1.8
±0.1
A
4.8x3.2 *2 dia.
Subminiature Basic Switch
Model
Operating
characteristics
Operating Force
Releasing Force
OF Max.
RF Min.
D2S-10L2@
D2S-5L2@
D2S-01L2@
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L2-F@
D2S-01L2-F@
0.18 N {18 gf}
0.02 N {2 gf}
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
19.3 mm
15.1±0.8 mm
D
2
S
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
*1. Stainless-steel lever
*2. Polyacetal resin roller
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Precautions
★
Please refer to "Basic Switches Common Precautions" for correct use.
Cautions
●Soldering
When using automatic soldering baths, we recommend soldering
at 260±5°C within 5 seconds. Make sure that the liquid surface
of the solder does not flow over the edge of the board.
When soldering terminals manually, complete the soldering at
the iron tip temperature between 350 to 400°C within 3 seconds,
and do not apply any external force for 1 minute after soldering.
When applying solder, keep the solder away from the case of the
Switch and do not allow solder or flux to flow into the case.
Correct Use
●Mounting
Use M2.3 mounting screw with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.23 to 0.26 N·m {2.3 to 2.7 kgf·cm}.
●Using
Micro Loads
Using a model for ordinary loads to open or close the contact of
a micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the following operating range, if inrush
current occurs when the contact is opened or closed, it may
increase the contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary. The N-level
reference value applies for the minimum applicable load. This
value indicates the malfunction reference level for the reliability
level of 60% (λ
60
).
(JIS C5003)
The equation,
λ
60
=0.5×10
-6
/operations indicates that the
1
estimated malfunction rate is less than
2,000,000
operations with
a reliability level of 60%.
Voltage (V)
0.16 mA
26 mA
100 mA
30
24
Normal load
type
Operating
range
D2S-5
D2S-10
Micro load type
Operating range
D2S-01
12
5
0
0.1
1 mA
1
10
100 mA 160 mA
100
1,000
Current (mA)
4
D2S
Subminiature Basic Switch
D
2
S
•
Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
•
Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
When setting breakpoints in C-SPY, I always get the error: Error[130]: "some breakpoint could not be set", no matter which statement I set it on, it can't be set.??? ??? ??? ??? ??? ??? ??? ??? ??? ??...
[i=s] This post was last edited by paulhyde on 2014-9-15 03:48 [/i] How can I power the arm board with ulink2? How do I set it up? Does anyone know? Please help me...
Many of Honeywell's new generation of sensors have I2C output.
I have two gas flow sensors on hand, so I want to test them on the EK-LM3S8962 development board.The program refers to Zhou Ligong's I2C ...
On September 1, 2007, the "2007 China Software Industry Development and Enterprise Innovation Summit" held in Nanjing released information that in the first half of this year, the national software in...
The corporate training company provides training for company employees and is looking for part-time matlab simulink teachers. The training is usually short-term, about three days, mainly on weekends. ...
On August 24th, Tesla CEO Elon
Musk
revealed information about the upcoming FSD V14, claiming it will outperform human drivers. Tesla FSD lead Ashok stated last year that FSD version 12.5, ...[Details]
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
ISP devices, such as field programmable devices (FPGAs and CPLDs), do not require a programmer. Using programming kits provided by the device manufacturer, they employ a top-down modular design app...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
1. Ease of Use: The HMI module should be designed to be simple and clear, allowing users to easily operate and configure the energy storage device.
2. Ease of Maintenance: The HMI module should...[Details]
On August 22, according to CNBC's report today, the National Highway Traffic Safety Administration (NHTSA) is launching an investigation into Tesla, and the latter is questioned whether it has fail...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
Electric vehicles will revolutionize transportation, changing fuel consumption, carbon emissions, costs, maintenance, and driving habits. Currently, a major selling point for electric vehicles is t...[Details]
Introduction: In digital circuit calculations, there is no concept of decimal points. You know where the decimal is, but the circuit does not know where the decimal point is. Therefore, you need to...[Details]
The composition of the water heater
The water heater itself is divided into the following parts:
1. Water tank.
This is where the water heater is filled with water and where the wate...[Details]
I recently read an article in the Wall Street Journal titled "We need the right to repair our gadgets" (reference original article: ). The author was very angry about the phenomenon of "planned obs...[Details]
introduction
With the development of society, people's requirements for the quality of refrigerated and frozen foods are constantly improving. The changes in food appearance and nutritional co...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
