HD74ALVCH16827
20-bit Buffers / Drivers with 3-state Outputs
ADE-205-140B (Z)
3rd. Edition
December 1999
Description
The HD74ALVCH16827 is composed of two 10-bit sections with separated output enable signals. For
either 10-bit buffer section, the two output enable (1OE1 and 1OE2 or 2OE1 and 2OE2) inputs must both
be low for the corresponding Y outputs to be active. If either output enable input is high, the outputs of that
10-bit buffer section are in the high impedance state. Active bus hold circuitry is provided to hold unused
or floating data inputs at a valid logic level.
Features
•
V
CC
= 2.3 V to 3.6 V
•
Typical V
OL
ground bounce < 0.8 V (@V
CC
= 3.3 V, Ta = 25°C)
•
Typical V
OH
undershoot > 2.0 V (@V
CC
= 3.3 V, Ta = 25°C)
•
High output current
±24
mA (@V
CC
= 3.0 V)
•
Bus hold on data inputs eliminates the need for external pullup / pulldown resistors
Function Table
Inputs
OE1
L
L
H
X
H : High level
L : Low level
X : Immaterial
Z : High impedance
OE2
L
L
X
H
A
L
H
X
X
L
H
Z
Z
Output Y
HD74ALVCH16827
Absolute Maximum Ratings
Item
Supply voltage
Input voltage
*1
Output voltage
*1, 2
Input clamp current
Output clamp current
Continuous output current
V
CC
, GND current / pin
Maximum power dissipation
at Ta = 55°C (in still air)
*3
Storage temperature
Notes:
Symbol
V
CC
V
I
V
O
I
IK
I
OK
I
O
I
CC
or I
GND
P
T
Tstg
Ratings
–0.5 to 4.6
–0.5 to 4.6
–0.5 to V
CC
+0.5
–50
±50
±50
±100
1
–65 to 150
Unit
V
V
V
mA
mA
mA
mA
W
°C
TSSOP
V
I
< 0
V
O
< 0 or V
O
> V
CC
V
O
= 0 to V
CC
Conditions
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage
to the device. These are stress ratings only, and functional operation of the device at these or
any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute maximum rated conditions for extended periods may affect device
reliability.
1. The input and output negative voltage ratings may be exceeded if the input and output clamp
current ratings are observed.
2. This value is limited to 4.6 V maximum.
3. The maximum package power dissipation is calculated using a junction temperature of 150°C
and a board trace length of 750 mils.
Recommended Operating Conditions
Item
Supply voltage
Input voltage
Output voltage
High level output current
Symbol
V
CC
V
I
V
O
I
OH
Min
2.3
0
0
—
—
—
Low level output current
I
OL
—
—
—
Input transition rise or fall rate
Operating temperature
∆t
/
∆v
Ta
0
–40
Max
3.6
V
CC
V
CC
–12
–12
–24
12
12
24
10
85
ns / V
°C
mA
Unit
V
V
V
mA
V
CC
= 2.3 V
V
CC
= 2.7 V
V
CC
= 3.0 V
V
CC
= 2.3 V
V
CC
= 2.7 V
V
CC
= 3.0 V
Conditions
Note: Unused control inputs must be held high or low to prevent them from floating.
3
HD74ALVCH16827
Electrical Characteristics
(Ta = –40 to 85°C)
Item
Input voltage
Symbol V
CC
(V)
*1
V
IH
2.3 to 2.7
2.7 to 3.6
V
IL
2.3 to 2.7
2.7 to 3.6
Output voltage
V
OH
Min
1.7
2.0
—
—
Max
—
—
0.7
0.8
—
—
—
—
—
—
0.2
0.4
0.7
0.4
0.55
±5
—
—
—
—
±500
±10
40
750
µA
µA
µA
µA
V
I
OH
= –100
µA
I
OH
= –6 mA, V
IH
= 1.7 V
I
OH
= –12 mA, V
IH
= 1.7 V
I
OH
= –12 mA, V
IH
= 2.0 V
I
OH
= –12 mA, V
IH
= 2.0 V
I
OH
= –24 mA, V
IH
= 2.0 V
I
OL
= 100
µA
I
OL
= 6 mA, V
IL
= 0.7 V
I
OL
= 12 mA, V
IL
= 0.7 V
I
OL
= 12 mA, V
IL
= 0.8 V
I
OL
= 24 mA, V
IL
= 0.8 V
V
IN
= V
CC
or GND
V
IN
= 0.7 V
V
IN
= 1.7 V
V
IN
= 0.8 V
V
IN
= 2.0 V
V
IN
= 0 to 3.6 V
V
OUT
= V
CC
or GND
V
IN
= V
CC
or GND
V
IN
= one input at (V
CC
–0.6) V,
other inputs at V
CC
or GND
Unit
V
Test Conditions
Min to Max V
CC
–0.2
2.3
2.3
2.7
3.0
3.0
2.0
1.7
2.2
2.4
2.0
V
OL
Min to Max —
2.3
2.3
2.7
3.0
—
—
—
—
—
45
–45
75
–75
—
—
—
—
Input current
I
IN
I
IN (hold)
3.6
2.3
2.3
3.0
3.0
3.6
Off state output current
*2
I
OZ
∆I
CC
3.6
3.6
3.0 to 3.6
Quiescent supply current I
CC
Notes: 1. For conditions shown as Min or Max, use the appropriate values under recommended operating
conditions.
2. For I/O ports, the parameter I
OZ
includes the input leakage current.
5
京公网安备 11010802033920号
EEWORLD
