C&K Connector Specification CS FR022, amendment to the ESCC Generic Specification n° 3401, for low cost products manufactured :
- in the same ESA qualified site
- through the same manufacturing and control processes
- with the same piece parts
- with lighter controls, documentation and traceability
Applications : Engineering models, ground equipments, testing, some flight equipments (no need for high requirements).
The connectors and accessories, supplied according to these 2 quality levels, are totally compatible, interchangeable, and intermateable, as they are
manufactured with the same piece parts (except the cables), in the same ESA qualified site.
Connector Styles
Description of the 3 Connector Styles proposed for the Space applications (Combinations of Configurations and Quality Levels).
Connector Style
Space ESA
Space FR022
Standard FR022
Configuration
ESA
ESA
Standard
Quality Level
ESA
FR022
FR022
Configuration characteristics.
Accessories
Cavity filled with epoxy
Guide Posts
Polarization key
Latching (even number of cavities)
Latching (odd number of cavities)
Configuration ESA
1 & N (mandatory)
2 & N-1 (mandatory)
3 to N-2 (option)
N/2 (option)
N/2 – 1 (option)
Configuration Standard
N.A.
1 & N (option)
1 to N (option)
N/2 (option)
N/2 – 1 (option)
Dimensions are shown in mm (inch)
Dimensions subject to change
137
Microminiature Connectors Type MTB1 Space
Performance Specifications
Operating Temperature range
Storage Temperature range
Working Voltage
(between contacts and contact and shell)
Rated Current
Insulation Resistance (500 V DC)
Voltage Proof
Contact Retention in insert
Engagement / Separation Forces
(Male Contacts)
-55°C / +125°C (-67°F / +257°F)
-55°C / +125°C (-67°F / +257°F)
Sea level
150 Vrms
33000 m (108240 feet) altitude
100 Vrms
AWG 26 Wire
2,5 A max.
AWG 28 Wire
1,5 A max.
Solid uninsulated Wire
2,5 A max.
5000 M
min.
600 Vrms / 2.0 mA max. leakage current
22,25 N max. / No contact axial displacement allowed
Gauge Fixture
Max.
Min.
Separation Force (N min.)
Inner diameter
min. / max.
0,559 (.0220) / 0,564 (.0222)
0,582 (.0229) / 0,587 (.0231)
0,137
Engagement Force (N max.)
1,667
Mating / Unmating Forces (per contact)
Mechanical Endurance
Contact Resistance
Mating : 2.2 N max.
Unmating : 0.14 N min. / 2.2 N max.
500 cycles mating/unmating
Low level current (10 mA / 20 mV DC) : 6.0 m
Rated current : 5.0 m max.
Nb of Contacts per Connector
2 to 4
5 to 14
15 and over
max.
AWG 26 Wire
2,0 A max.
1,8 A max.
1,4 A max.
AWG 28 Wire
1,4 A max.
1,2 A max.
0,9 A max.
Maximum Rated Current
Solid uninsulated Wire
2,0 A max.
1,8 A max.
1,4 A max.
Maximum Weight
Male Contact
Female contact
Plug Insulator
Receptacle Insulator
Guide Posts (pair)
Latching Plug part
Latching Receptacle part
Solid Uninsulated Wire
Insulated Cable AWG26 (ESCC 390101302B)
Insulated Cable AWG28 (ESCC 390101301B)
20000 Gamma max. (NM)
0.020 g
0.020 g
0.021 g / cavity
0.006 g / cavity
0.035 g
0.030 g
0.040 g
1.60 g / m
2.30 g / m
1.80 g / m
Residual Magnetism Level
Dimensions are shown in mm (inch)
Dimensions subject to change
138
Microminiature Connectors Type MTB1 Space
Contact Design
Welded tip
Sleeve
Wire
Crimp area
Wire crimp
The high-performance and reliable contact characteristics are obtained by the Micropin
TM
contact system.
The flexible "twist-pin" spring contact consists of 7 strands of 0,127 (.005) diameter beryllium copper wire helically wound around a core of 3 strands
0,09 (.0035) diameter soft copper wire.
This wire bundle is crimped into a sleeve at one end. The other end is terminated with a hemispherically shaped weld.
The wire bundle is compressed to create a bulge with a diameter slightly larger than the socket inside diameter.
The pin elongates and twists when it enters the socket. Electrical contact is maintained along 7 spiral lines.
The socket is a precision-made tube with a chamfered lead-in.
Normal mating conditions
Severe misalignment
Twist-pin contacts will mate even under severe misalignment.
The flexible twist-pin is recessed into the insulator and the rigid socket is exposed, reversing the traditional positions of pin and socket.
During mating, the socket is guided into the pin insulator by the lead-in chamfer.
The pin is kept from flexing beyond the socket capture radius by the walls of the cavity.
The hemispherical weld of controlled radius at the tip of the pin combines with the lead-in chamfers of the socket contact and the pin insulator to
cam the pin into alignment.
By controlling the welding process and the dimensions of the socket contact and the insulators, it is impossible for the recessed pin to escape the
socket capture radius.
Dimensions are shown in mm (inch)
Dimensions subject to change
139
Microminiature Connectors Type MTB1 Space
Terminations
Harness type insulated cables : AWG 26 to AWG 28, 7 strand, single-core cables.
I recently wrote the USB driver for my phone , Motorola L6, on 2440. Now the driver can be loaded. It can also read data and device descriptors, etc. But there is a problem that every time I unplug my...
Use the following circuit diagram to build an AC-DC conversion circuit. It is found that during the experiment: 1. The input signal frequency f=10KHz, the amplitude is about Vin=5Vpp sinusoidal signal...
A: I have blocked these two in the device tree, and now they are all changed to LEDs.B: I need to change them to GPIO in iomuxc.A: I have blocked and even deleted them in the device tree, why doesn't ...
Proteus ISIS is a circuit analysis and physical simulation software developed by Labcenter, a British company. It runs on the Windows operating system and can simulate and analyze (SPICE) various anal...
Brothers who work in electronics will come into contact with all kinds of wires, PCB copper foil circuits, chip pins, etc. that need to be soldered, bridged or repaired... How fine is the finest work ...
Help: How is the internal AD conversion performed in the ez430-RF2500 development board? Why is the data obtained after the sine wave I input is different from the data I calculated after the internal...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
introduction
Sudan's Muglad Oilfield is a large oilfield jointly invested, developed and constructed by a four-party consortium of China, Malaysia, Canada and Sudan. It consists of 8 satellite...[Details]
The biggest advantage of Profibus is that it is guaranteed by the stable international standard EN50170 and has been proven to be universal in practical applications. It has been widely used in man...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
The programmable controller directly controls the stepper motor, which can significantly reduce the cost of the control system of the modular machine tool automatic production line. The article int...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
