EEWORLDEEWORLDEEWORLD

Part Number

Search

S1206CUG223M10-W

Description
Fixed Resistor, Metal Glaze/thick Film, 0.25W, 22000ohm, 100V, 20% +/-Tol, -100,100ppm/Cel, 1206,
CategoryPassive components    The resistor   
File Size126KB,1 Pages
ManufacturerState of the Art Inc.
Environmental Compliance
Download Datasheet Parametric View All

S1206CUG223M10-W Overview

Fixed Resistor, Metal Glaze/thick Film, 0.25W, 22000ohm, 100V, 20% +/-Tol, -100,100ppm/Cel, 1206,

S1206CUG223M10-W Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid225167891
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.55
structureChip
JESD-609 codee4
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.46 mm
Package length3.2 mm
Package formSMT
Package width1.55 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
resistance22000 Ω
Resistor typeFIXED RESISTOR
series1206(STD)-THICKFILM
size code1206
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceGold (Au)
Tolerance20%
Operating Voltage100 V

S1206CUG223M10-W Preview

1206 Thick Film Chip Resistor
Standard Grade, Wraparound
PERFORMANCE CHARACTERISTICS
Resistance Range
Tolerances (1)
TCR
Thermal Resistance
Maximum Power
Maximum Voltage
(1)+/- 0.5% limited availability
1
W-40
M
W
0.5%,1%, 2%, 5%,10%
±100, ±200, ±300 ppm
77.1°C/W
250 mW
100 Volts
GLASS
PASSIVATION
RESISTOR
FILM
96% ALUMINA CHIP
WRAPAROUND
TERMINATIONS
CURRENT NOISE
TEMPERATURE RISE (°C)
POWER DISSIPATION
fiber epoxy board
ceramic board
ENVIRONMENTAL PERFORMANCE (2)
Thermal Shock
Low Temperature Operation
Short-time Overload
Resistance to Bonding Exposure
Moisture Resistance
High Temperature Exposure
Life Test
±0.03%
±0.03%
±0.03%
±0.03%
±0.05%
±0.05%
See Chart
POWER DISSIPATION (WATTS)
LIFE TEST
POWER DERATING
(2)Typical resistance change, test methods and criteria
per MIL-PRF-55342.
PART NUMBERING
S 1206 C P X 150 J 20 - TR
PACKAGING CODE: - TR = Tape/Reel - W = Waffle Carrier (Default packaging is Bulk)
TEMPERATURE CHARACTERISTIC: 10: ±100 ppm 20: ±200 ppm 30: ±300 ppm
TOLERANCE: F: 1% G: 2% J: 5% K: 10% M: 20%
RESISTANCE VALUE:
Four digits are used for tolerances of 1% or lower, three digits are used above 1%. Leading digits are significant while the last digit
specifies the number of zeros to add. The letter "R" is used to represent the decimal for fractional ohmic values. Example: 5R6 is 5.6
ohms.
TERMINATION FINISH: X: Sn60 over Nickel (Solderable) C: Silver bearing (Epoxy bondable-RoHS) G: Gold (Epoxy bondable-RoHS)
Y: Silver over Nickel (Solderable -RoHS) Z: Gold over Nickel (Solderable-RoHS)
PRODUCT DESIGNATION: P: Thick film on alumina U: Untrimmed alumina (10% & 20% tolerance only)
TERMINATION TYPE: C: Wraparound termination
SIZE CODE
GRADE: S: Standard Production H: High Reliability (For Screening options, contact the factory)
MECHANICAL
.156
INCHES
MILLIMETERS
Length
Width
Thickness
Top Term
Bottom Term
Gap
Approx. Weight
.126 (.124 - .134)
.061 (.059 - .067)
.018 (.015 - .023)
.016 (.010 - .025)
.018 (.010 - .025)
.090 (.086 - .094)
.0084 grams
3.20
1.55
0.46
0.41
0.46
2.29
(3.15 - 3.40)
(1.50 - 1.70)
(0.38 - 0.58)
(0.25 - 0.64)
(0.25 - 0.64)
(2.18 - 2.39)
MINIMUM
RECOMMENDED
MOUNTING
PADS
(INCHES)
.067
.084
.036
“Specifications subject to change without notice.”
STATE OF THE ART, INC.
2470 Fox Hill Road, State College, PA 16803-1797
Phone (814) 355-8004
www.resistor.com
Fax (814) 355-2714
Toll Free 1-800-458-3401
02/08/08
How to use an op amp for full-wave rectification?
As the title says, how to use an op amp to do full-wave rectification? That is, flip the other negative half cycle, and use the op amp and diode to achieve it, so as to minimize the waveform distortio...
gaoyang9992006 Power technology
Dspace dead zone circuit part
This is the block diagram of the dead zone circuit. The sampling signal sent by the Hall sensor is input through the pin header JP2. The signal is input into the Butterworth filter circuit through the...
fish001 DSP and ARM Processors
Security-Reset Circuit
ZC803/809/810 series circuits are microprocessor reset circuits used to monitor power supply voltage or battery voltage. This series of circuits does not require peripheral devices, thereby improving ...
oicw911 Industrial Control Electronics
Help: Friends who have installed WinCE on ARM boards please come in
I am using s3c2410. After burning Nboot_Debug.bin and Eboot.nb0 files to the development board, when I run DNW, there is no display page on the DNW software. What is the reason? Also, when I use PB cu...
poorcabbage Embedded System
Electromagnetic Interference (EMI) Suppression Technology
[b]1 Basic Concepts of Electromagnetic Interference In a complex electromagnetic environment, any electronic or electrical product can withstand a certain amount of external electromagnetic interferen...
clj2004000 Robotics Development
Help a friend to sell a 9999 new Tissot mother-of-pearl dial ladies watch
[font=微软雅黑][size=3][color=#666666] This is my friend's watch. [/color][color=#666666] I bought it in the Tissot store in Beijing Xinzhongguan Shopping Mall in mid-June. [color=#666666] I only tried it...
eric_wang Buy&Sell

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 401  132  2925  1095  2820  9  3  59  23  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号