EEWORLDEEWORLDEEWORLD

Part Number

Search

2091-1524/020-000

Description
Strip Terminal Block
CategoryThe connector    terminals   
File Size146KB,4 Pages
ManufacturerWAGO
Websitehttps://www.wago.com/
Environmental Compliance
Download Datasheet Parametric View All

2091-1524/020-000 Overview

Strip Terminal Block

2091-1524/020-000 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerWAGO
Reach Compliance Codeunknown
ECCN codeEAR99
Is SamacsysN
Terminal and terminal strip typesSTRIP TERMINAL BLOCK
Base Number Matches1
Printview: Male connector; 4-pole; Pin spacing 3.5 mm / 0.138 in; with snap-in mounting foot - Item No.:
2091-1524/020-000
.
Male connector; 4-pole; Pin spacing 3.5 mm / 0.138 in; with snap-
in mounting foot
Item No.: 2091-1524/020-000
.
Male connector; 4-pole; Pin spacing 3.5 mm / 0.138 in; with snap-in mounting foot
.
Marking
.
Business data
Supplier
Item no.
GTIN / EAN
Content
Order amount
Customer item number
.
Notes
WAGO
2091-1524/020-000
4050821161400
1
200
Item description:Universal connection for all conductor typesSimple, push-in termination of solid and ferruled
conductorsEasy-to-use design does not require special toolsTesting parallel to conductor entry – tip contactFor “wire-
to-wire” and “board-to-wire” connectionsIntegrated release lever
Technical data
Miscellaneous
No. of poles
Pin spacing
Total number of connection points
Total number of potentials
Color
Ratings according to 1
Rated voltage (III / 3) [V]
4
3.5 mm (0.138 in %)
4
4
light gray
IEC/EN 60664-1
160 [V]
WAGO Kontakttechnik GmbH & Co. KG
1
【Development and application based on NUCLEO-F746ZG motor】11. Parameter configuration - ADC configuration
In the development of servo drive, ADC acquisition is the key point. The analog quantities in this development board are: three-phase current, 1 bus voltage, and 1 temperature (onboard sensor). After ...
annysky2012 Motor Drive Control(Motor Control)
About dsp5402 communication problem
I made a dsp5402 minimum system, which can make a light flash, but it can't work after connecting the communication part. It can't connect to the simulator. It can connect occasionally, but it will pr...
cdfly DSP and ARM Processors
WinDriver interrupt problem
It seems that the efficiency of receiving interrupts using windriver is not high. How can I set it up to write PlugIn? I tried the operation described in the document and it doesn't seem to work. It a...
lao3 Embedded System
Participate in the HELPER2416 development board scholarship program: Reconstructed modbus slave
I have been a bit busy recently and have missed a lot of work. Modbus is a commonly used communication protocol in the field of industrial control, and freemodbus has added a lot of convenience to eng...
hongyancl Embedded System
[Solved] CRC check code conversion
[i=s] This post was last edited by 416202554 on 2015-5-30 23:14 [/i] MSP430FR5969 supports hardware CRC checksum, but the checksum uses the CRC CCITT standard, while the existing host computer uses th...
416202554 Microcontroller MCU
How to play Ubuntu
ctrl+alt+F5, enter command mode, sometimes the ls command displays too much, how to scroll to see the previous one? No scroll bar, mouse pointer is gone...
jasonx Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1695  1005  67  564  773  35  21  2  12  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号