EEWORLDEEWORLDEEWORLD

Part Number

Search

NVFMAS25DC485BD

Description
Switching capacity up to 25A
File Size146KB,2 Pages
ManufacturerDBLECTRO
Websitehttp://www.dblectro.com
Download Datasheet View All

NVFMAS25DC485BD Overview

Switching capacity up to 25A

NVFMAS25DC485BD Preview

23×15.5×26
Features
Switching capacity up to 25A.
PC board mounting and insert mounting available.
Suitable for automation system and automobile auxiliary etc.
Ordering Information
NVFM C
Z 20
DC12V 1.5 b
7
D
8
5 Coil rated Voltage(V):DC:6,12,24,48
6 Coil power consumption:1.2:1.2W;1.5:1.5W
7 Terminals b: PCB type;a: plug in type
8 Coil transient suppression: D: with diode;
R: with resistant;.
NIL: standard
1
2
3
4
5
6
1 Part number:NVFM
2 Contact arrangement:A:1A (1.2W);C:1C(1.5W)
3 Enclosure:S: Sealed type;Z: Dust cover;
4 Contact Current:25:25A/14VDC;20:20A/14VDC
Contact Data
Contact Arrangement
Contact Material
Contact Rating (resistive)
Max. Switching Power
Max. Switching Voltage
Contact Resistance or Voltage drop
Operation
Electrical
life
Mechanical
1A SPSTNO
f1C
SPDT(B-M)
Ag SnO
2
, AgNi Ag CdO
1A 25A/14VDC 1C 20A/14VDC
350W
75VDC
Max. Switching Current:25A
50m
Item 3.12 of IEC255-7
5
10
Item 3.30 of IEC255-7
10
7
Item 3.31 of IEC255-7
Coil Parameter
Coil voltage
VDC
Pickup
voltage
VDC(max)
(70%of rated
voltage )
release
voltage
VDC(min)
(10% of rated
voltage)
0.6
1.2
2.4
4.8
0.6
1.2
2.4
4.8
1.5
10
7
1.2
10
7
Dash
numbers
Coil
resistance
±10%
Coil power
consumption
W
Operate
Time
ms
Release
Time
ms
Rated
006-1200
012-1200
024-1200
048-1200
006-1500
012-1500
024-1500
048-1500
6
12
24
48
6
12
24
48
Max.
7.8
15.6
31.2
62.4
7.8
15.6
31.2
62.4
30
120
480
1920
24
96
384
1536
4.2
8.4
16.8
33.6
4.2
8.4
16.8
33.6
CAUTION
:
1.The use of any coil voltage less than the rated coil voltage will compromise the operation of the relay.
2.Pickup and release voltage are for test purposes only and are not to be used as design criteria.
143
-40~85’
Ambient Temperature
85% (at 40’)
IEC68-2-3 Test Ca
Relative Humidity
Mass
18.5g
Note: 1). ,When testing, coil terminals shall be connect , if coil transient suppression is installed in relay .
Qualification inspection:
Perform the qualification test as specified in the table
of IEC255-19-1 and minimum sample size 24.
Dimensions (Unit: mm)
>àçÇá
nãîÜ>àç>ìòèÑ
Mounting (Bottom views)
na`>>ìòèÑ
Note: Footprint as shown above
is also available.
Dimensions
Wiring diagram (Bottom views)
mm
0.8
1.4
2.1
2.4
2.5
2.7
3.2
4.5
4.8
5.5
6.3
6.4
8
9
9.5
11.5
14
15
15.5
23
26
0.031
0.055
0.083
0.094
0.098
0.106
0.126
0.177
0.189
0.127
0.248
0.252
0.315
0.354
0.374
0.453
0.551
0.591
0.610
0.905
1.024
NOTES
1).Dimensions are in millimeter.
2).Inch equivalents are given for general information only.
Reference Data
How to write the driver for AT88SC0104 encryption chip
When I was developing the driver for AT88SC0104 on the S3C2410 development board, I was unable to write data into the configuration area. I don't know much about the commands (command, addr1, addr2, N...
Maywolf Embedded System
(Transfer) CC2640R2F BLE5.0 Bluetooth protocol stack Generic Attribute Profile (GATT)
[i=s]This post was last edited by freebsder on 2019-3-26 12:00[/i] [align=left][b][size=15.0pt]Generic Attribute Profile (GATT)[/size][/b][/align][align=left]Just as the GAP layer is responsible for c...
freebsder RF/Wirelessly
Beginner's guide to FPGA-2
September 29, 2011 8:30:261. assign is generally used in combinational logic, and the variables thereafter must be of wire type; for input and output variables, if their types are not declared, the de...
xiaomiking FPGA/CPLD
DM9000CEP
Does anyone have the hardware circuit diagram of the DM9000CEP module? Please give me a copy. Thanks....
曹伟1993 PCB Design
I need help... What should I do if the frequency band of the RC sine wave oscillator composed of LM324 is not wide enough?
In the analog electronics course, the RC sine wave oscillator circuit composed of the LM324 op amp uses the Wien bridge circuit. However, the teacher requires the frequency to reach 100KHz, saying tha...
iavas Analog electronics
Which expert can explain the principle of Ctrl+A, Ctrl+c, Ctrl+V using the knowledge of thread calling in the operating system? ?
Anyway, I have no idea at all. This operating system is too difficult to learn... I don't know where to post, so I'll post it here. If you have any ideas, please tell me and we'll all give you points!...
小牛b Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 600  347  490  710  2557  13  7  10  15  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号