EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-51GP4J1-18SVN

Description
Cable Assembly, 24AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-5-51GP4J1-18SVN Overview

Cable Assembly, 24AWG,

177-740-5-51GP4J1-18SVN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005109412
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL9.35
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D MALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.205 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.466 mm
MIL complianceYES
Number of conductors51
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.093 Ω
shieldYES
stay19X36
Wire gauge24 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
TMS320F28335 Study Notes - Startup Process
1.What is the starting address after DSP reset? 0x3FFFC0 2. What are the steps to burn a program into the emulator? Burn the program to the specified location according to the cmd file and then execut...
fish001 Microcontroller MCU
Can we start a DIY activity of FPGA USB emulator?
I have only seen FPGA boards on the forum, but where can I get an emulator? I hope the forum can launch a DIY activity of "FPGA emulator with USB interface", thank you...
desk1983 FPGA/CPLD
24bit ECC issues
The nand flash of TH58NVG6D2ETA20 requires 1KB 24-bit ECC. If I use 512B 12-bit ECC instead, will there be any risk? Thank you~~ What factors are related to the bit error rate of nand flash?...
cushat Embedded System
ST touch library anti-interference problem
I have made several products using the ST touch library. There are no problems in the office test,but the sensitivity is significantly reduced when it comes to production in the workshop.The total shi...
lygtian stm32/stm8
PIC level change interrupt
I am using PIC16F1823 chip, and I am very distressed that the level change interrupt cannot be accessed. I hope to get help from friends on the forum. The following is my program: #include htc.h #incl...
3050122050 MCU
Bottom-level development
I am doing wince driver development and bootloader development (under ARM). What preparatory knowledge do I need? Or how do I learn it? Please give me the steps, thank you!...
jw_1001 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2437  2213  2201  62  1724  50  45  2  35  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号