Product
Specification
High Speed Serial Data 2 Connector
1.
1.1.
SCOPE
Content
108-1965
27Jun06 Rev D
This specification covers performance, tests and quality requirements for the Tyco Electronics High
Speed Serial Data Connector 2 (HSSDC2) designed for applications requiring extremely high data
transfer rates over long distances. A right angle surface mount receptacle with seven high-speed
contacts is available. The plug connector assembly includes a printed circuit board terminated to the
cable at one end, and an edge card circuit pattern on the other end. The printed circuit board may or
may not have equalization circuitry. The shielded cable has four conductors and is available in 18, 24
and 26 AWG. A latch is included in the plug design.
1.2.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
1.3.
Qualification Test Results
Successful qualification testing on the subject product line was completed on 27Apr01. The
Qualification Test Report number for this testing is 501-509. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
2.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
2.1.
Tyco Electronics Documents
109-197: AMP Test Specifications vs EIA and IEC Test Methods
114-13028: Application Specification
501-509: Qualification Test Report
502-1121: Engineering Report
2.2.
3.
3.1.
Product shall be of the design, construction and physical dimensions specified on the applicable
product drawing.
©2006 Tyco Electronics Corporation
Harrisburg, PA
All International Rights Reserved.
!
!
!
!
!
!
Commercial Standards
EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications
IEEE SFF-8410: HSS Copper Testing and Performance Requirements
REQUIREMENTS
Design and Construction
* Trademark
| Indicates change
For latest revision, visit our website at www.tycoelectronics.com\documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
1 of 7
LOC B
108-1965
3.2.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
3.3.
Ratings
Voltage: 30 volts DC
Current: 0.5 ampere maximum
Temperature: -10 to 60 C
Characteristic Impedance: 100 ohms
Frequency Range: 0 to 5 Gbps
/
3.4.
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per EIA-364.
3.5.
Test Requirements and Procedures Summary
Test Description
Initial examination of product.
Requirement
Meets requirements of product
drawing.
Meets visual requirements.
ELECTRICAL
Dry circuit resistance.
70 milliohms maximum.
R 20 milliohms maximum.
EIA-364-23.
Subject specimens to 100
milliamperes maximum and 20
millivolts maximum open circuit
voltage.
See Figure 3.
EIA-364-21.
Test between adjacent contacts of
unmated specimens.
Procedure
EIA-364-18.
Visual and dimensional (C of C)
inspection per product drawing.
EIA-364-18.
Visual inspection.
Final examination of product.
Insulation resistance.
Dielectric withstanding voltage.
350 volts AC at sea level.
EIA-364-20,
1 minute hold with no breakdown or Condition I.
flashover.
Test between adjacent contacts of
unmated specimens.
See Note (2).
See Note (2).
See Note (2).
See Note (2).
See Note (2).
Figure 1 (continued)
IEEE SFF-8410.
IEEE SFF-8410.
IEEE SFF-8410.
IEEE SFF-8410.
IEEE SFF-8410.
Impedance.
Eye pattern.
Insertion loss.
Return loss.
Near end crosstalk (NEXT).
Rev D
)
!
!
!
!
!
Performance and Test Description
1000 megohms minimum.
2 of 7
108-1965
Test Description
Requirement
MECHANICAL
Solderability.
Vibration, random.
Solderable area shall have a
minimum of 95% solder coverage.
EIA-364-638.
Subject contacts to solderability.
Procedure
No discontinuities of 1 microsecond EIA-364-28, Test Condition VII,
or longer duration.
Condition D.
See Note (1).
Subject mated specimens to 3.10
G's rms between 20-500 Hz. 15
minutes in each of 3 mutually
perpendicular planes.
No discontinuities of 1 microsecond EIA-364-27, Method H.
or longer duration.
Subject mated specimens to 30 G's
See Note (1).
half-sine shock pulses of 11
milliseconds duration. 3 shocks in
each direction applied along 3
mutually perpendicular planes, 18
total shocks.
See Note (1).
EIA-364-9.
Mate and unmate specimens for
250 cycles at a maximum rate of
500 cycles per hour.
EIA-364-13.
Measure force necessary to mate
specimens at a maximum rate of
12.7 mm [.5 in] per minute.
EIA-364-13.
After fully depressing the retention
latch, measure force necessary to
unmate specimens at a maximum
rate of 12.7 mm [.5 in] per minute.
EIA-364-38.
Apply specified load in an axial
direction.
EIA-364-38.
Applied specified load to the cable
plug in a plane parallel to the I/O
panel.
See Figure 4.
EIA-364-38.
Applied specified load to the cable
plug in a plane parallel to the I/O
panel.
See Figure 5.
Mechanical shock.
Durability.
Mating force.
30 N [6.7 lb] maximum.
|
Unmating force.
10 N [2.25 lb] minimum.
Retention force.
Specimens shall remain mated
when a force of 75 N [16.9 lb] is
applied. No opens detected.
Specimens shall remain mated
when a force of 75 N [16.9 lb] is
applied. No opens detected.
Side load force.
Longitudinal force.
Specimens shall remain mated
when a force of 100 N [22.5 lb] is
applied. No opens detected.
Figure 1 (continued)
Rev D
3 of 7
108-1965
Test Description
Requirement
ENVIRONMENTAL
Thermal shock.
See Note (1).
EIA-364-32.
Subject unmated specimens to 5
cycles between -10 and 70°C.
EIA-364-31, Method III.
Subject unmated specimens to 10
cycles (10 days) between 25 and
65°C at 80 to 100% RH.
EIA-364-17, Method A, Test
Condition 2, Test Time Condition
C.
Subject mated specimens to 70°C
for 500 hours.
EIA-364-65, Class IIA.
Subject specimens to
environmental Class IIA for 7days
unmated, and 7 days mated.
Procedure
Humidity-temperature cycling.
See Note (1).
Temperature life.
See Note (1).
Mixed flowing gas.
See Note (1).
NOTE
(1)
(2)
Shall meet visual requirements, show no physical damage, and meet requirements of
additional tests as specified in the Product Qualification and Requalification Test Sequence
shown in Figure 2.
This test was not performed as part of the Qualification Test Sequence for product covered
by this specification. See Engineering Report 502-1121 for details of these tests.
Figure 1 (end)
Rev D
4 of 7
108-1965
3.6.
Product Qualification and Requalification Test Sequence
Test Group (a)
Test or Examination
1
2
3
4
5
6
7
8
Test Sequence (b)
Initial examination of product
Dry circuit resistance
Insulation resistance
Dielectric withstanding voltage
Solderability
Vibration
Mechanical shock
Durability
Mating force
Unmating force
Retention force
Side load force
Longitudinal force
Thermal shock
Humidity-temperature cycling
Temperature life
Mixed flowing gas
Final examination of product
NOTE
9
5
3(c)
3(c)
5
8
3
3
3
3
4
5
5
6
4
2
8
2(d)
2(d)
2(d)
1
3,7
1
2,4
1
2,4
2,6
3,7
2
1
1
1
1
1
(a)
(b)
(c)
(d)
See paragraph 4.1.A.
Numbers indicate sequence in which tests are performed.
Precondition specimens with 50 durability cycles.
Test shall be conducted with receptacles soldered to printed circuit boards and
mounted to an I/O panel.
Figure 2
4.
4.1.
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. All test groups shall each consist of 6 specimens.
B.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 2.
Rev D
5 of 7
京公网安备 11010802033920号
EEWORLD
