EEWORLDEEWORLDEEWORLD

Part Number

Search

16.000MHZHC49/T/50/10/0/SR/ATF

Description
Series - Fundamental Quartz Crystal, 16MHz Nom, RESISTANCE WELDED, HERMATIC SEALED PACKAGE-2
CategoryPassive components    Crystal/resonator   
File Size156KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

16.000MHZHC49/T/50/10/0/SR/ATF Overview

Series - Fundamental Quartz Crystal, 16MHz Nom, RESISTANCE WELDED, HERMATIC SEALED PACKAGE-2

16.000MHZHC49/T/50/10/0/SR/ATF Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionRESISTANCE WELDED, HERMATIC SEALED PACKAGE-2
Reach Compliance Codecompliant
Is SamacsysN
Ageing3 PPM/FIRST YEAR
Crystal/Resonator TypeSERIES - FUNDAMENTAL
Drive level1000 µW
frequency stability0.001%
frequency tolerance50 ppm
Installation featuresTHROUGH HOLE MOUNT
Nominal operating frequency16 MHz
Maximum operating temperature50 °C
Minimum operating temperature
physical sizeL11.5XB4.9XH11.2 (mm)/L0.453XB0.193XH0.441 (inch)
Series resistance25 Ω
surface mountNO
Base Number Matches1
THROUGH-HOLE CRYSTALS
HC49 SERIES CRYSTALS
DESCRIPTION
HC49 crystals are a long-established industry-standard part. Basic
specification HC49 crystals provide the lowest cost crystal available but
these crystals can also be manufactured to very close tolerances and low
ESR values. Holder variants are HC49/T (truncated), providing a lower
height version, 3-wire versions where the crystal base and body can be
earthed by a centre earth wire and HC50 which has larger diameter leads
specifically for socket mounting.
OUTLINES & DIMENSIONS
FEATURES
·
·
·
·
·
·
Very low cost crystal
Available with close tolerances
Fully customisable specification
Comprehensive Euroquartz stockholding
Industry-standard package with options
Very wide frequency range
GENERAL SPECIFICATION
Frequency Range:
Calibration Tolerance at 25ºC:
Frequency stability over temp:
Load Capacitance:
Ageing:
Drive level:
Static capacitance (C0):
Holder:
Part Numbers for Holder Variants *
Holder Type
Standard 2 lead:
Low height versions:
Centre Earth Lead:
Centre Earth Lead (Low):
‘Plug-in’ for use in socket:
Holder Designation
HC49
HC49/T (from 4.0MHz)
HC49/3W
HC49/T/3W (from 4.0MHz)
HC-50
1.0MHz to 250.0MHz
from ±3ppm to ±50ppm
from ±3ppm to ±100ppm
8pF to 50pF, or Series
±3ppm max 1st year,
±1ppm max per year after
1mW max
7pF max
Resistance-weld, hermetic seal
* HC49 crystals are also available for surface-mount applications with
formed leads and fitted with a clip. See ‘49MJ’ in the surface-mount
crystal section on Euroquartz website; www.euroquartz.co.uk
OSCILLATION MODE & ESR
Frequency
(MHz)
1.0 ~ 1.3
2.01 ~ 3.0
3.01 ~ 3.2
3.21 ~ 3.5
3.51 ~ 3.9
3.91 ~ 5.0
5.01 ~ 7.0
7.01 ~ 10.0
10.0 ~ 30.0
30.1 ~ 45
24.0 ~ 100
80.0 ~ 160
110 ~ 250
Crystal Cut/
Oscillation Mode
SL Fund.
AT Fund.
AT Fund.
AT Fund.
AT Fund
AT Fund.
AT Fund.
AT Fund.
AT Fund.
AT Fund.
AT 3
rd
OT
AT 5th OT
AT 7th OT
ESR (max)
(Ohms)
5000
400
200
150
120
100
50
35
25
20
40
70
120
FREQUENCY STABILITY OVER TEMPERATURE
Operating
Temp. °C
0° to +50°
-10° to +60°
-20° to +70°
-30° to +80°
-40° to +90°
-55° to +105°
Temperature Stability (ppm)
±3
ü
ü
X
X
X
X
±5
ü
ü
ü
X
X
X
±7.5
ü
ü
ü
X
X
X
±10
ü
ü
ü
ü
X
X
±15
ü
ü
ü
ü
ü
X
±20
ü
ü
ü
ü
ü
ü
±30
ü
ü
ü
ü
ü
ü
PART NUMBER GENERATION
HC49 crystal part numbers are derived as follows:
ü
Indicates this stability is available over the stated operating temp. range
Example:
16.000MHz HC49/30/50/10/30pF/ATF
Frequency/Holder/Calibration/Temp. Stability/ Temp. Range/Circuit
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 1460 230000 Fax: +44 1460 230001 email: info@euroquartz.co.uk web: www.euroquartz.co.uk
Has anyone used LaunchPad's debug interface directly to their own board?
Has anyone used the LaunchPad debug interface to connect directly to their own board? I was going to do it last time, but then I didn't do it because of the board area and wiring. But there is no grou...
wangfuchong Microcontroller MCU
Is it better to connect two LED lights in series or in parallel to make them have the same brightness?
Two different LEDs, the anode is connected to +5V, and the cathode is connected to the I/O port. If you want the brightness to be the same when they are lit, is it better to connect them in series or ...
dirty Analog electronics
Remote login router settings
How to effectively manage Huawei 3COM routing devices? The most common way is to use the telnet command. As mentioned above, if the IP address of a router interface is 192.168.1.1, then we can execute...
liudong2008lldd RF/Wirelessly
LM3S8962 Development Board Ethernet Development Notes
Use the LM3S8962 development board to learn Ethernet related development 8962 integrates mac and phy but it seems that there is no protocol stack. I still don't understand the lwip of the example prog...
eeleader Microcontroller MCU
Learn Linux in Action in One Week
[align=left][color=rgb(102, 102, 102)][font=Tahoma][size=12pt] [/size][/font][/color][color=rgb(102, 102, 102)][font=微软雅黑][size=15pt]Linux is an open source, free operating system. Its stability, secu...
EE大学堂 Training Edition
CreateThread error in the driver
In the driver initialization function, create a threadif ( (pAXP182->IST = CreateThread(NULL, 0, AXP182_IST, NULL, 0, NULL)) == NULL) { dwErr = GetLastError(); DEBUGMSG(ZONE_ERR,(TEXT("AXP182_Init ERR...
neil.wang Embedded System

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2271  2521  255  387  453  46  51  6  8  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号