EEWORLDEEWORLDEEWORLD

Part Number

Search

177-714-2-51GS4K1-24PCN

Description
Interconnection Device
CategoryThe connector    The connector   
File Size436KB,4 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-714-2-51GS4K1-24PCN Overview

Interconnection Device

177-714-2-51GS4K1-24PCN Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
Connector typeINTERCONNECTION DEVICE
Base Number Matches1
MWDM Micro-D Shielded Cable Assemblies
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly
labor. 100% tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair
177-740 cables are furnished with a full complement of
white/blue twisted pair wires.
Integral Shield Termination–The
connector shell has a
platform to accept Band-It shield termination bands. The
cable shield braid is attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding with
Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully
shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector
shell and secured with a stainless steel
BAND-IT
® clamp. These pre-wired, 100% tested assemblies meet the
requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.
Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either
single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
– A gold-plated
stainless steel ground spring on the pin connector mating face offers
substantial improvement in EMI protection. The graphs compare
identical connectors tested with and without ground springs.
EMI Performance with Ground Spring
SHIELDING EFFECTIVENESS (DB)
SHIELDING EFFECTIVENESS (DB)
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
EMI Performance without Ground Spring
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
FREQUENCY (Hz)
FREQUENCY (Hz)
© 2006 Glenair, Inc.
CAGE Code 06324/0CA77
Printed in U.S.A.
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
www.glenair.com
B-8
E-Mail: sales@glenair.com
For reference by students who are new to Multisim
[float=left]This includes the basic operations of the electronic software Multisim, as well as some common circuit routines. You can directly open the routines and conduct simulation experiments. Gene...
jqh_111 Download Centre
A revolution in benchtop power supply testing
Power has been integral to electrical engineering since the days of Edison and Tesla, so much so that there was a time when designers took it for granted that it was the last task in the design proces...
黑衣人 Power technology
Design of a precision successive approximation ADC reference voltage source
[b][size=4]Precision Successive Approximation ADC Reference Design[/size][/b] [align=left][size=14pt] The overall accuracy of a high-resolution, successive approximation ADC depends on the precision, ...
dontium Energy Infrastructure?
Is it necessary to switch modes when nesting arm interrupts?
I see that in arm's irq interrupt handler, the scene is protected in the assembly code, and then the cpsr is modified to clear the I_bit, and then the IRQ mode is switched to the sys mode, and then th...
zhang223 ARM Technology
I need help with the setting of external resistor voltage divider for 4152 LCD.
Moderator and all the masters:I am using 4152 chip. Now, in order to reduce power consumption, I use external resistor voltage divider to drive LCD. I have tried 750K, 680K, and 470K resistors respect...
ahoo Analogue and Mixed Signal
[Ask TI] The C280X series found that after the GPIO port configuration is initialized, it will automatically become a low level
I recently did PWM and accidentally found that the PWM output is high level by default when powered on, but after initializing the GPIO port configuration (setting the pull-up resistor and the GPIO po...
安_然 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1482  895  347  1716  2375  30  19  7  35  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号