E1SAB18-48.000M
Series
RoHS Compliant (Pb-free) Resistance Welded Short
HC-49/UP SMD Crystal
Frequency Tolerance/Stability
±50ppm at 25°C, ±100ppm over 0°C to +70°C
Mode of Operation
AT-Cut Third Overtone
RoHS
Pb
E1S A B 18 -48.000M
Nominal Frequency
48.000MHz
Load Capacitance
18pF Parallel Resonant
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
Aging at 25°C
Load Capacitance
Shunt Capacitance (C0)
Equivalent Series Resistance
Mode of Operation
Drive Level
Storage Temperature Range
Insulation Resistance
48.000MHz
±50ppm at 25°C, ±100ppm over 0°C to +70°C
±5ppm/year Maximum
18pF Parallel Resonant
7pF Maximum
100 Ohms Maximum
AT-Cut Third Overtone
1mWatt Maximum
-40°C to +125°C
500 Megaohms Minimum at 100Vdc
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test
Gross Leak Test
Lead Termination
Mechanical Shock
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 1014 Condition A
MIL-STD-883, Method 1014 Condition C
Sn 2µm - 6µm
MIL-STD-202, Method 213 Condition C
MIL-STD-202, Method 210
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010
MIL-STD-883, Method 2007 Condition A
MECHANICAL DIMENSIONS (all dimensions in millimeters)
LINE MARKING
1
3.20
MAX
E48.000M
E=Ecliptek Designator
M=MHz
13.30 MAX
4.85
MAX
4.88 ±0.20
0.50 MIN (x2)
0.80 ±0.30 (x2)
11.60 MAX
NOTE: Coplanarity 0.360 MAX
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 1 of 4
E1SAB18-48.000M
Suggested Solder Pad Layout
All Dimensions in Millimeters
5.5 (X2)
2.0 (X2)
4.0
Solder Land
(X2)
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 2 of 4
E1SAB18-48.000M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
High Temperature Infrared/Convection
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
3°C/second Maximum
150°C
175°C
200°C
60 - 180 Seconds
3°C/second Maximum
217°C
60 - 150 Seconds
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 3 of 4
E1SAB18-48.000M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
Low Temperature Infrared/Convection 245°C
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
5°C/second Maximum
N/A
150°C
N/A
30 - 60 Seconds
5°C/second Maximum
150°C
200 Seconds Maximum
245°C Maximum
245°C Maximum 2 Times / 230°C Maximum 1 Time
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 4 of 4
京公网安备 11010802033920号
EEWORLD
