Socket compatible EPROM pin configurations are shown in the blocks adjacent to the NMC27C64 pins.
Pin Names
A0–A12
CE
OE
O
0
–O
7
PGM
NC
V
PP
V
CC
GND
Addresses
Chip Enable
Output Enable
Outputs
Program
No Connect
Programming
Voltage
Power Supply
Ground
Commercial Temperature Range
V
CC
= 5V
±10%
Parameter/Order Number
NMC27C64Q, N 150
NMC27C64Q, N 200
Access Time (ns)
150
200
Extended Temp Range (-40
°
C to +85
°
C)
V
CC
= 5V
±10%
Parameter/Order Number
NMC27C64QE, NE200
Access Time (ns)
200
2
NMC27C64 Rev. C
www.fairchildsemi.com
NMC27C64 65,536-Bit (8192 x 8) CMOS EPROM
Absolute Maximum Ratings
(Note 1)
Temperature Under Bias
Storage Temperature
All Input Voltages except A9
with Respect to Ground (Note 10)
-55°C to +125°C
-65°C to +150°C
+6.5V to -0.6V
Power Dissipation
Lead Temperature
(Soldering, 10 sec.)
ESD Rating
(Mil Spec 883C,
Method 3015.2)
1.0W
300°C
2000V
All Output Voltages
with Respect to Ground (Note 10)V
CC
+1.0V to GND -0.6V
V
PP
Supply Voltage and A
9
with Respect to Ground
During Programming
V
CC
Supply Voltage with
Respect to Ground
Operating Conditions
(Note 7)
Temperature Range
NMC27C64Q 150, 200
NMC27C64N 150, 200
NMC27C64QE 200
NMC27C64NE 200
V
CC
Power Supply
0°C to +70°C
-40°C to +85°C
+5V
±10%
+14.0V to -0.6V
+7.0V to -0.6V
READ OPERATION
DC Electrical Characteristics
Symbol
I
LI
I
LO
I
CC1
(Note 9)
I
CC2
(Note 9)
I
CCSB1
I
CCSB2
I
PP
V
IL
V
IH
V
OL1
V
OH1
V
OL2
V
OH2
Parameter
Input Load Current
Output Leakage Current
V
CC
Current (Active)
TTL Inputs
V
CC
Current (Active)
CMOS Inputs
V
CC
Current (Standby)
TTL Inputs
V
CC
Current (Standby)
CMOS Inputs
VPP Load Current
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Output Low Voltage
Output High Voltage
Conditions
V
IN
= V
CC
or GND
V
OUT
= V
CC
or GND, CE = V
IH
CE = V
IL
,f=5 MHz
Inputs = V
IH
or V
IL
, I/O = 0 mA
CE = GND, f = 5 MHz
Inputs = V
CC
or GND, I/O = 0 mA
CE = V
IH
CE = V
CC
V
PP
= V
CC
Min
Typ
Max
10
10
Units
µA
µA
mA
mA
mA
µA
5
3
0.1
0.5
10
-0.1
2.0
20
10
1
100
µA
0.8
V
CC
+1
0.45
V
V
V
V
I
OL
= 2.1 mA
I
OH
= -400
µA
I
OL
= 0
µA
I
OH
= 0
µA
V
CC
- 0.1
2.4
0.1
V
V
AC Electrical Characteristics
NMC27C64
Symbol
t
ACC
t
CE
t
OE
t
DF
t
CF
t
OH
Parameter
Address to
Output Delay
CE to Output Delay
OE to Output Delay
OE High to Output Float
CE High to Output Float
Output Hold from
Addresses, CE or OE ,
Whichever Occurred First
Conditions
Min
CE = OE = V
IL
PGM = V
IH
OE = V
IL
, PGM = V
IH
CE = V
IL
, PGM = V
IH
CE = V
IL
, PGM = V
IH
OE = V
IL
, PGM = V
IH
CE = OE = V
IL
PGM = V
IH
0
0
0
150
Max
150
150
60
60
60
0
0
0
200, E200
Min
Max
200
200
60
60
60
Units
ns
ns
ns
ns
ns
ns
3
NMC27C64 Rev. C
www.fairchildsemi.com
NMC27C64 65,536-Bit (8192 x 8) CMOS EPROM
Capacitance
TA = +25˚C, f = 1 MHz (Note 2) NMC27C64Q
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Output Capacitance
Conditions
V
IN
= 0V
V
OUT
= 0V
Typ
6
9
Max
8
12
Units
pF
pF
Capacitance
TA = +25˚C, f = 1 MHz (Note 2) NMC27C64N
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Output Capacitance
Conditions
V
IN
= 0V
V
OUT
= 0V
Typ
5
8
Max
10
10
Units
pF
pF
AC Test Conditions
Output Load
1 TTL Gate and C
L
= 100 pF (Note 8)
≤5
ns
0.45V to 2.4V
0.8V and 2V
0.8V and 2V
Input Rise and Fall Times
Input Pulse Levels
Timing Measurement Reference Level
Inputs
Outputs
AC Waveforms
(Note 6) (Note 9)
ADDRESS
2V
0.8V
Address Valid
CE
2V
0.8V
t
CF
t
CE
t
OE
(Note 3)
(Notes 4, 5)
OE
2V
0.8V
t
DF
(Notes 4, 5)
Valid Output
OUTPUT
2V
0.8V
Hi-Z
t
ACC
(Note 3)
Hi-Z
t
OH
Note 1:
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Note 2:
This parameter is only sampled and is not 100% tested.
Note 3:
OE may be delayed up to t
ACC
- t
OE
after the falling edge of CE without impacting t
ACC
.
Note 4:
The t
DF
and t
CF
compare level is determined as follows:
High to TRI-STATE ® , the measured V
OH1
(DC) ˛ 0.10V;
Low to TRI-STATE, the measured V
OL1
(DC) + 0.10V.
Note 5:
TRI-STATE may be attained using OE or CE .
Note 6:
The power switching characteristics of EPROMs require careful device decoupling. It is recommended that at least a 0.1
µF
ceramic capacitor be used on every device
between V
CC
and GND.
Note 7:
The outputs must be restricted to V
CC
+ 1.0V to avoid latch-up and device damage.
Note 8:
1 TTL Gate: I
OL
= 1.6 mA, I
OH
= -400
µA.
C
L
: 100 pF includes fixture capacitance.
Note 9:
V
PP
may be connected to V
CC
except during programming.
Note 10:
Inputs and outputs can undershoot to -2.0V for 20 ns Max.
First, the bandwidth. This is usually written on the probe, how many MHz. If the bandwidth of the probe is not enough, no matter how high the bandwidth of the oscilloscope is, it is useless, and it is...
void delay(unsigned int x) //about 1.5us{ while(x) { x--; } } void init_1820(void) { DS18B20_SET; DS18B20_CRL; delay(400); //more than 480us DDRC|=(1
It seems that there is a problem with the timing: ...
https://bbs.eeworld.com.cn/upfiles/img/20076/200761219310933.jpg The driver chip is ILI9320 SPI interface QVGA TFT LCD! We are further studying the source code part... yea!...
Dear friends, I am using EVC4.0, and I just started using it. When compiling a program, the following error occurs: fatal error C1189: #error: Database classes not supported in this library variant. I...
1. Structural featuresFPGAa. There are a large number of logic gates and triggers in the chip, most of which are lookup table structures, and the implementation process is mostly SRAMb. It can be quic...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:02[/i] LCD monitors are becoming more and more popular with users. Several major monitor manufacturers around the world have also turne...
As a natural human-machine interface, voice can make the in-vehicle navigation system safer and more user-friendly. Through the functional comparison of domestic and foreign in-vehicle navigation s...[Details]
Magnetic resonance imaging (MRI) systems can take high-resolution cross-sectional perspective images of the human body, providing very useful information for medical diagnosis. The radio frequency pro...[Details]
Embedded systems are the replacement products of computer technology, communication technology, semiconductor technology, microelectronics technology, voice and image data transmission technology, and...[Details]
Radio Frequency Identification (RFID) technology is a contactless automatic identification technology that uses radio frequency signals to read and write relevant data from target objects to achiev...[Details]
As FPGAs incorporate more and more capabilities, the need for effective debugging tools will become more critical. Careful planning for internal visibility will enable teams to adopt the right debuggi...[Details]
Designers of hearing aids have stringent requirements. Hearing aids must be small enough to fit in or behind the ear, operate on ultra-low power, and be free of noise or distortion. To meet these requ...[Details]
The hardware circuit principle is shown in Figure 1. In the specific design, each part should consider the anti-interference problem to minimize the impact of interference on the performance of the...[Details]
Many MEMS devices, such as accelerometers and mechanical resonance devices, require a vacuum environment to realize their designed functions. However, verifying whether the package cavity has reach...[Details]
Overview
Currently, many portable consumer electronic products, such as mobile phones, PDAs, MP3 players, and notebooks, are equipped with display screens. Although the type and size of the di...[Details]
System Introduction
EraSoC-1000 series chips are high-performance SoCs (System on Chips) based on the Loongson core. With their powerful CPU processing capabilities, 64-bit floating-point ...[Details]
Introduction
Wireless operators are driving demand for broadband and data rates by offering enhanced data services to increase average revenue per user (ARPU). The need to provide users with ...[Details]
Abstract:
This paper
introduces a data acquisition system based on USB and DSP, which takes advantage of the high-speed transmission characteristics of USB2.0. The overall structure of the ...[Details]
Abstract: This paper introduces the origin and new features of MP4, and introduces the core audio compression technology MPEG-2 AAC (Advanced Audio Coding) based on MP4. Finally, it briefly summari...[Details]
Electrocardiogram is an important means of diagnosing heart disease. However, due to various reasons, it is difficult to capture abnormal electrocardiograms with ordinary electrocardiographs. Although...[Details]
A financial analyst pointed out that the signal reception problems of Apple's 3G iPhone may be caused by some defective chips.
Richard Windsor, an analyst at Nomura Securities, said in a resea...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
