51 single-chip microcomputer, written in C language, the function is to design a six-bit clock. Hours: minutes: seconds. Based on AT89c2051, the proteus simulation diagram is ready. Please write accor...
I bought an advanced simulator, IAR6.2 is recommended, but the following problem always occurs when I compile the program under IAR6.2However, there is no problem when I compile it under the original ...
Use cvavr 2.05 to learn xmega, super fast to get started. The codewizard in it is very easy to use, you can quickly get started to learn to set up various xmega peripherals....
Paid help: I recently participated in an embedded system development project. The DSP used in the system is Philips' TM1300, and the operating system is the pSOS embedded system. My main job is to dev...
module DSP_RST(input clk_25m, input RESETSTAT, //DSP reset status 0 means reset status 1 means working statusinput LOCKED, //Is the clock module normal?
output ref LRESETNMIENz = 1'b0,//局部复位管脚
output ...
After decompression, use VS05 to open MFC_Decode.sln 1 Compile MFCLib 2 Compile MMFrameExtractLib 3 Compile and execute MFC_DecodeDemo After compiling, I cannot decode MP4 format movies on my 6410 dev...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
I. Introduction
In the field of power conversion, isolated converters (forward, flyback, and double-ended) with low output DC voltage all use MOSFET as the rectifier device. Since these devi...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]