TOKO Inc.
IC Data Sheet
TK111xxC
Regulator with on/off
TK111xxC
Features
・Very
good stability CL=0.1μF is steady enough. Any type can be used.（1.8V≦Vout）
・Very
low Dropout Voltage. Vd=120mV at 100mA
・
High Precision output Voltage（±1.5％ or
±50mV）
・Good
ripple rejection ratio（80dB at 1KHz）
・
Wide operating voltage range(1.8V∼14V)
・Built
in Short circuit protection
・Peak
output current is 320mA.(0.3V down point)
・
Built-in Thermal Shutdown
・Very
low quiescent current (Iq=63uA at Io=0mA)
・Available
Very Low Noise Application
・
Built-in on/off Control (0.1μA Max Standby current） High On
・Very
Small Surface Mount Packages
・Built
in reverse bias over current protection
Description
TK111xxC is an integrated circuit of the silicon monolithic bipolar structure, and the regulator of
the low saturation output type with very little quiescent current(63μA).
The PNP power transistor is built into. The I/O voltage difference when the current of Typ.200mA is
supplied to the system is 0.2V. The voltage source can be effectively used
Therefore, It is the best for the battery use set.
The on/off function is built into IC. The current at standing-by mode becomes slight (pA level).
1.5-10.0V is arranged to the output voltage in 0.1V step. The output voltage is trimmed in high
accuracy. The best voltage for the set used will be able to be selected.
The over current sensor circuit and the reverse-bias over current obstruction circuit are built into.
It is a design not broken because an ESD is also high. It is possible to use (*O) at ease.
When mounting on PCB, the loss becomes about 500mW though the package is very small.
TK111xxC uses the circuit with very high stability in DC and AC.
The capacitor on the output side is steady in 0.1μF (1.8V≦Vout). The kind of this capacitor is not
asked. It is possible to use every type capacitor.
However, a good characteristic is shown the more overall larger this capacitor is.
The ripple rejection is 84dB at 400Hz and 80dB at 1kHz.
GG3-H008B
Page
2
TOKO Inc.
C rank device
IC Data Sheet
Absolute maximum ratings
TK111xxC
Parameters
Symbol
Limiting Values
Unit
Supply voltage
Ｖcc
Max
−0.4∼１6
V
Reverse bias
VrMax
−0.4∼6
V
Np pin voltage
VnpMax
−0.4∼5
V
Control pin voltage
VcontMax
−0.4∼16
V
Storage temperature Range
Tstg
−55∼150
℃
Operating voltage range
Vop
1.8∼14
Ｖ
Operating temperature range
Top
-30∼80
℃
Short circuit current
Ishort
360
mA
Power dissipation
Internal limited（150mW unit）
500mW mounted (reference)
5 pin mini flat package
Electrical characteristics
Parameters
Output voltage
Line regulation
Load regulation
Drop-out voltage
Test Condition
Symbol
Min
Ｔyp
Vout
LinReg
LoaReg
See table 1
0.0
Vtest=Vout
Typ
+1V
Vcont=1.8V
（Ta＝25℃）
Max
5
Unit
½V
Condition
Maximum output
current
Consumption current
Icc
63
100
Vcc=8V , Vcont≦0.15V Off state
Standing by current
Istanby
0.0
0.1
µA
½A
Iout=50½A
Quiescent current
Iq
1.0
1.8
Control terminal Specification (Pull down resistor =500k
（Note
2）
Vcont＝1.8½ on state
Control current
Icont
5
15
µA
Control voltage
Vcont
1.6
V
on
state
0.6
V
V
off
state
（11） （28）
（27） （64）
Vdrop
80
140
120
210
200
350
230
350
1.5V≦Vout≦2.0V：No regulation
240
320
IoutMax
250
Vtest=Vout
Typ
+1V---- Vout
Typ
ΔV=5V
+6V
½V
5mA＜Iout＜100mA note 1
mV 5mA＜Iout＜200mA note 1
mV
Ｉout=50mA
mV
Ｉout=100mA
mV
Ｉout=200mA
(2.4V≦Vout)
mV
Ｉout=180mA
(2.1V≦Vout＜2.4V)
Because of Vop
Min
=1.8V
½A
When
（
Vout
Typ
.×0.9）
Reference Value
mA
1.8V≦Vcc≦2.1V
Ｉout=0mA
Except Icont
µA
Np treminal Voltage
VNp
1.28
Typ=35 ppm/℃
Reference Value
Vo
Vo/Ta
0.14∼0.25
µV/√Hz
at 1KHz
Reference Value
Out put noise
Vno
Note 1: This value depends on the output voltage. (It is a value of Vout=3V device.)
This item improves in a low voltage device.
Note 2: The input current decreases to the pA level by connecting control terminal to GND.（Off state）
Pull-down resistor is 500KΩ.
General Note:
Limits are guaranteed by production testing or correction techniques using Statistical Quality Control (S
QC) methods. Unless otherwise noted. Vtest=Vout
Typ
+1v；IL=1mA（Tj=25
℃）The
operation of -30℃-80℃
is guaranteed in the design by a usual inspection.
General Note: Exceeding the “Absolute Maximum Rating “ may damage the device
General Note: Connecting a capacitor to the noise bypass pin can decrease the output noise voltage
General Note: Output noise is 0.14-0.25
µV/√Hz
at 1KHz : 25∼65µVrms at BW400-80kHz
General Note: The ripple rejection is 84dB at 400Hz and 80dB at 1kHz.
［CL=1.0µF,Cnp=0.01μF,Vnois=200mV
RMS
,Vin=Vout
Typ
+1.5v,Iout=10mA½
GG3-H008B
Page
4
京公网安备 11010802033920号
EEWORLD
