EEWORLDEEWORLDEEWORLD

Part Number

Search

385-022-1

Description
Card Edge Connector, 22 Contact(s), 1 Row(s), Female, Straight, Solder Terminal
CategoryThe connector    The connector   
File Size339KB,2 Pages
ManufacturerEDAC
Download Datasheet Parametric View All

385-022-1 Overview

Card Edge Connector, 22 Contact(s), 1 Row(s), Female, Straight, Solder Terminal

385-022-1 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
Other featuresHIGH PROFILE, POLARIZED
Connector typeCARD EDGE CONNECTOR
Contact point genderFEMALE
DIN complianceNO
Filter functionNO
IEC complianceNO
MIL complianceNO
Manufacturer's serial number385
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded1
Terminal pitch3.96 mm
Termination typeSOLDER
Total number of contacts22
UL Flammability Code94V-0
Base Number Matches1
The Raspberry Pi discount quota is full. Check out other e-selected products to participate in the event
Recently, the products in e-Mall's "e-Select" magazine have been jointly organized by the forum. If you buy the products mentioned in the magazine, you can get a reward of 50 or 100 yuan. The quantity...
nmg Embedded System
【Video】DIY process of wireless remote control handle based on 51 single chip microcomputer
:)[font=微软雅黑][size=4][color=#ff0000]First of all, I wish you all a happy Chinese New Year[/color][/size][/font]:)[font=微软雅黑][size=4] I recently recorded a DIY video of a wireless remote control handle...
@ZiShi DIY/Open Source Hardware
Go your own way and let the SI engineer decide
SI engineer: "You may need to change all the routing for this part."I didn't expect to get this answer from the SI engineer: "No, I'm serious."A few short sentences can actually mean a lot. They not o...
yvonneGan PCB Design
Op amp bias problem caused by pre-stage RC filtering during weak signal detection
Recently, I was working on a problem of using a copper-clad board as a handwriting board. I needed to detect extremely weak signals (0.2mV and above). Because there was a lot of noise, I used a filter...
扶摇- Analog electronics
Wince 6.0 restart or reset problem..
I have a question about the restart of wince 6.0, please help me... According to the Internet, restart (hot start) calls the IOCTL_HAL_REBOOT function of the OAL layer to restart or call SetSystemPowe...
dingedward Embedded System
Help
I used 3843 to make a flyback switching power supply (input 220V, output 24V/100W, feedback package 18V), the frequency is 40KHZ, but as soon as the power is turned on, 3843, mos, and C14 are damaged ...
zgbpower Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2753  2516  2623  1050  2293  56  51  53  22  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号