EEWORLDEEWORLDEEWORLD

Part Number

Search

HTSW-210-12-S-S

Description
Board Connector, 10 Contact(s), 1 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT
CategoryThe connector    The connector   
File Size216KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Environmental Compliance  
Download Datasheet Parametric View All

HTSW-210-12-S-S Overview

Board Connector, 10 Contact(s), 1 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT

HTSW-210-12-S-S Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
body width0.098 inch
subject depth0.1 inch
body length1.9 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD
Contact completed and terminatedGold (Au)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee4
MIL complianceNO
Plug contact pitch0.2 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
OptionsGENERAL PURPOSE
PCB contact patternRECTANGULAR
reliabilityCOMMERCIAL
Terminal pitch5.08 mm
Termination typeSOLDER
Total number of contacts10
Base Number Matches1
Why is InitializeHandler not called automatically by the NDIS driver?
A network card driver, using NDIS5.1, added CDEFINES=$(CDEFINES) -DNDIS_MINIPORT_DRIVER=1 -DNDIS51_MINIPORT=1 in sources, initialized in DriverEntry: NDIS_MINIPORT_CHARACTERISTICS ch; ... ch.MajorNdis...
saqi99 Embedded System
[ESP32-Korvo Review] 08 ESP-Skainet Development Preparation
[i=s]This post was last edited by Tianyiwuzui on 2021-3-20 20:30[/i]After a few nights of hard work, I finally set up the ESP-IDF development environment. Now it’s time to get down to business: voice ...
天意无罪 Domestic Chip Exchange
[Ask] How to handle multiple interrupts in Keil more reasonably and avoid exceptions?
For example: I use a circular queue to store and send messages. The queue uses an array of fixed length, where the length of the array must be longer than each message. There are 8 arrays in the queue...
digi01 Embedded System
Digital tube size list
Digital tube size list, collected from the Internet...
刘小飞 Discrete Device
Compilation Error Help
The following is the IIC bus write byte subroutine I wrote, but the compilation error is as follows !E D:\AVR文件\PCF8591\8591.c(65): unrecognized statement!E D:\AVR文件\PCF8591\8591.c(66): syntax error; ...
hz_university Microchip MCU
Solution to inaccurate AD sampling
1: The reference voltage needs to be accurate enough. It is recommended to use an external high-precision reference voltage.2: If the PGA is adjustable, the smaller the gain coefficient is, the lower ...
Aguilera Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1031  1833  681  2741  2336  21  37  14  56  48 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号