The AD I use is AD73360, 16-bit serial, but it does not have an SPI interface. How can I use MSP430 to implement a software serial port to communicate with the AD? Do any experts have the source code?...
[font=微软雅黑][size=4]According to the votes of the Toshiba Electronics Show WeChat Live Group, today we will expose the Toshiba Electronics Show's automotive electronics exhibition board. [/size][/font]...
Cypress Semiconductor recently announced that sales of its Programmable System-on-Chip (PSoC) mixed-signal array devices have exceeded 100 million. Cypress said that this figure fully proves that this...
I bought a knock-off version of JLINK online. I can use this JLINK to download programs to STM32F103, and can debug in single steps or set breakpoints online. However, when debugging online, the varia...
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
Recently, the "Smart Photovoltaic Industry Development Action Plan (2018-2020)" jointly issued by six departments has put this concept on the forefront. Photovoltaic smart solutions will become the ne...[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
In 2018, the National Development and Reform Commission issued a new photovoltaic subsidy policy. The benchmark on-grid electricity price was significantly reduced, the return on investment decreased,...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
OSC_IN and OSC_OUT are external crystal pins by default. If you do not use an external crystal oscillator on the STM32, how to connect OSC_IN and OSC_OUT If you use the internal RC oscillator instead...[Details]
The frequency calculation formula of the PWM wave generated by the output comparison mode of the timer is: 72M/((2*(arr+1))*(psc+1) ) For example, if you set: PWM_Init(1000-1,72-1); (PWM_Init(arr,psc...[Details]
/*----------------------------------------------- Name: IIC protocol PCF8591 AD/DA conversion Content: Use DA input, digital tube display output digital quantity, LED display analog voltage size ...[Details]
The STC12C5412AD microcontroller is an enhanced 8051 standard 51 series microcontroller. It is 12 times faster than the ordinary 8051 and can be programmed on a home computer without an emulator. ...[Details]
Homemade LED Electronics Clocks can be seen in many electronic newspapers and magazines, but most of them need to reset the time and other parameters after power failure, which brings a lot of inco...[Details]
An example of Samsung S3C/S3P/S3F9XXX series MCU implementing table lookup operation ; to implement table lookup operation, you must first define the table address, there are two ways t...[Details]
In this example, a single-byte binary number (0X20) is converted into uncompressed BCD code and stored in 0X25, 0X24, and 0X23, where 0X25 is the hundreds place and 0X23 is the ones place. main: MOV ...[Details]
Common glass tube thermometers rely on the rise and fall of mercury in the tube to determine the temperature. When the light is dim, the position of mercury cannot be seen clearly, which brings incon...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
