(1) Reset until clock pulse 18 (on declining flank).
Minimum integration time = (133-18) * CLK period + 10µs (this is the time the S&H cap needs to follow).
At 500kHz clock speed, the minimum integration time becomes 0.240ms.
(2) At 125°C, the integration time should be limited to 2ms.
(3) The SI pulse must go low before the rising edge of the next clock pulse.
390109025502
Rev. 008
Page 3 of 12
Nov/05
MLX90255-BA
Linear Optical Array
MLX90255BA Electrical specifications
All tests are made with 0.7ms integration time at 25°C at 880nm and with a clock speed of 500kHz in,
250kHz out, and 500kHz, unless otherwise specified in the Test Conditions. 100% light under Test
Conditions means that the light is set in such a way that there is 2.4V at the output of the chip.
Parameter
Symbol Test Conditions
Min
Typ
Max
Units
Sensitivity for devices with glas lid Sensitivity At 25°C
Sensitvity for open devices
Polyimide Wafer
Illumination (1)
Average analog output (1)
Average analog output
Average analog output
Highest Dark Pixel
Non Linearity
Pixel Response Non Uniformity (2)
Pixel Interaction Test (3)
Noise Level (4)
Hold spec, same as PRNU
Output Settling Time
Array Lag (5)
Dark Signal Non Uniformity (6)
Analog Output Saturation
Change in sensitivity with
Temperature at 880nm (7)
Operating Free Temp
Supply Current (8)
Idd
-40
2
5
Illum100
At 25°C, 2.4V at output
0.135
0.14
0.14
0.151
0.16
0.176
14
2.4
0
0
0.15
0.40
0.3
1.4
0.8
±0.5%
±4.0%
5%
3
±4.0%
450
0.5%
80
140
3.0
0.3
125
8
120
440
6
±8.5%
750
±1.2%
±8.5%
0.179
0.19
0.21
W/cm²
V
V
V
V
FS
FS
FS
mV (RMS)
FS
ns
FS
mV
mV
V
%/°C
°C
mA
V/ W/
cm2
VaoLight At 25°C, 100% light
Initial offset At 25°C, 0% light
VaoDark At 125°C, 0% light
Vaodarkmax At 125°C, 0.25ms integration time
Nlao1
PRNU
PIT
Vn
PRNUH
Ts
Alag
DSNU
All Temp
All Temp, 100% light
AT 25°C
All Temp
All Temp, 100% light, 62.5kHz
All Temp
At 25°C
At 25°C
At 125°C
All Temp
(0) After power on, the first integration scan is not guaranteed correct. This scan is needed for initializing digital levels on chip. After a SI and 133 proper
CLK signals, the system is fully initialized and all further scans are valid. The next SI will provide a valid scan.
(1) Absolute Light measurements are very test-setup dependent and should be regarded with caution. Relative measurements are possible with
±1%
accuracy.
(2) PRNU is defined as the worst case deviation of any PixelValue (pixel 3 till 130) to the average light value. PixelValue = (Vout of a pixel at 100% light
– Vout of same pixel at 0% light) The MLX90255BA has a cosine shaped gain: external pixels have 15% more gain than middle pixels.
1. Main features DS2770 is a battery fuel gauge and lithium/nickel chemical battery charger integrated device produced by Dallas Semiconductor. It can communicate with the main system through the 1-Wi...
[i=s] This post was last edited by Dianyu Electronics Engineer on 2019-9-27 10:23 [/i]The first thing to do when designing a 4.3 -inch screen is to select the model. I used to think that the basis of ...
I want to read some books about embedded development on mobile phones. Please recommend the following books about embedded, C, or Linux. I have experience in languages such as Java and .NET. I only le...
[i=s]This post was last edited by dontium on 2015-1-23 13:35[/i] According to the ADS7804 manual, how can the analog input pin have a voltage of 2.07V when there is no analog input?...
In addition to providing transmission channels for video signals, optical transceivers can also provide a variety of other signal transmission channels, such as audio signals, asynchronous data signal...
In the early 1990s, portable phones were all the rage. With the rapid development of electronic technology, today's mobile phones can not only send emails and text messages, but also take photos, ch...[Details]
Ultrasonic tooth cleaning machines have been widely used in the medical field. Most ultrasonic tooth cleaning machines used at home and abroad now use analog oscillation circuits. There are the follow...[Details]
A biped robot joint constructed by pneumatic artificial muscles is introduced. The joint uses the flexible characteristics of pneumatic artificial muscles to effectively control the impact of the la...[Details]
Introduction
The market for wireless telemetry products is developing rapidly. Recently, the industry has also set off a revolution in wireless applications. Wireless telemetry technol...[Details]
This issue will briefly introduce the test related to spectrum - occupied bandwidth.
Definition: Occupied bandwidth refers to the bandwidth corresponding to 99% of the total transmitted power, cent...[Details]
When you hear the word digital TV, you may feel fresh and excited, but when it comes to what digital TV is and what it can bring us, you may still be confused. You must be very eager to understa...[Details]
summary
Theoretically explains how to set up a PFC boost regulator using a current sensing transformer with the UCC3817 control IC.
1. Schematic
The schematic diagram is show...[Details]
A well-designed electronic load is not designed just for use in the lab; it should be carefully designed and built to test actual power systems. This is true for military portable systems, such as ...[Details]
1. Introduction
The UCC28051 reference design is a 100W offline AC/DC voltage converter with power factor correction (PFC). This power module design is intended to illustrate how to proper...[Details]
introduction
Controller Area Network (CAN) is a bus standard proposed by Bosch of Germany to solve the information communication between automotive electronic control units. With its exc...[Details]
introduction
Like other
portable
electronic products,
blood flow parameter detectors
need to be small, thin, durable, reliable, and have a long standby time. Therefore, system desi...[Details]
Preface
For a long time, SD cards with Flash Memory as storage have been widely used in consumer electronic products due to their small size, low power consumption, erasable and non-volati...[Details]
In today's world, terrorism poses a severe challenge to social development, national stability and human progress. "Terrorism, political corruption and environmental pollution" are known as the thr...[Details]
Power semiconductors and reactive components (capacitors and inductors) are ubiquitous in today's electrical equipment. In normal operation, they can cause two undesirable side effects on the AC line ...[Details]
Abstract
Modbus protocol has become the first choice of communication protocol in the current industrial field due to its openness, transparency, low cost and easy development. This paper int...[Details]
Automotive Electronics
京公网安备 11010802033920号
EEWORLD
