• Supports LVTTL switching levels on the RESET pin
• Output drivers have controlled edge rates, so no
external resistors are required
• Two KV ESD protection
• Latch-up performance exceeds 100 mA: JESD78, Class II
• Conforms to JEDEC STD (JESD82-3) for buffered DDR
DIMMs
• 48-pin TSSOP
When RESET is LOW, the differential input receivers are
disabled, and undriven (floating) data, clock, and REF voltage
inputs are allowed. In addition, when RESET is LOW, all
registers are reset and all outputs force to the LOW state. The
LVCMOS RESET input must always be held at a valid logic
HIGH or LOW level.
To ensure defined outputs from the register before a stable
clock has been supplied, RESET must be held in the LOW
state during power-up.
In the DDR registered DIMM application, RESET is specified
to be completely asynchronous with respect to CLK and CLK.
Therefore, no timing relationship can be guaranteed between
the two. When entering reset, the register will be cleared and
the outputs will be driven LOW quickly, relative to the time to
disable the differential input receivers, thus ensuring no
glitches on the output. However, when coming out of reset, the
register will become active quickly, relative to the time to
enable the differential input receivers. As long as the data
inputs are low, and the clock is stable during the time from the
LOW-to-HIGH transition of RESET until the input receivers are
fully enabled, the design must ensure that the outputs will
remain LOW.
Description
This 14-bit registered buffer is designed specifically for 2.3V to
2.7V V
DD
operation and is characterized for operation from
0°C to + 85°C.
All inputs are compatible with the JEDEC Standard for
SSTL_2, except the LVCMOS reset (RESET) input. All outputs
are SSTL_2, Class II-compatible.
The SSTV16857 operates from a differential clock (CLK and
CLK). Data is measured at the crossing of CLK going HIGH,
and CLK going LOW.
Block Diagram
Pin Configuration
Q1
Q2
VSS
VDDQ
Q3
Q4
Q5
VSS
VDDQ
Q6
Q7
VDDQ
VSS
Q8
Q9
VDDQ
VSS
Q10
Q11
Q12
VDDQ
VSS
Q13
Q14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
D1
D2
VSS
VDD
D3
D4
D5
D6
D7
CLK
CLK
VDD
VSS
VREF
RESET
D8
D9
D10
D11
D12
VDD
VSS
D13
D14
RESET
CLK
CLK
VREF
D1
1D
C1
R
Q1
To 13 Other Channels
Rev 1.0, November 21, 2006
2200 Laurelwood Road, Santa Clara, CA 95054
Tel:(408) 855-0555
Fax:(408) 855-0550
CY2SSTV16857
Page 1 of 7
www.SpectraLinear.com
CY2SSTV16857
Pin Description
Pin
34
3,8,13,17,22,27,36,46
28, 37, 45
1, 2, 5, 6, 7, 10, 11, 14, 15, 18, 19,
20, 23, 24
25, 26, 29, 30, 31, 32, 33, 40, 41,
42, 43, 44, 47, 48
39, 38
4, 8, 12, 16, 21
35
Name
RESET
VSS
VDD
Q(1:14)
D(1:14)
CLK, CLK
VDDQ
VREF
I/O
I
Ground
Power
O
I
I/I
Power
I
Ground.
2.5V nominal supply voltage.
Data outputs, SSTL_2, Class II output.
Data input clocked on the crossing of the rising edge
of CLK, and the falling edge of CLK.
Differential clock input.
Power supply voltage quiet, 2.5V nominal.
Input reference voltage, 1.25V nominal.
Type
Description
Rev 1.0, November 21, 2006
Page 2 of 7
CY2SSTV16857
Absolute Maximum Conditions
[1, 2, 3]
This device contains circuitry designed to protect the inputs
against damage due to high static voltages or electric field;
however, precautions should be taken to avoid application of
any voltage higher than the maximum rated voltages to this
circuit. For proper operation, V
in
and V
out
should be
constrained to the range:
Parameter
V
DD
V
DD
V
in
V
out
I
OUT
I
IK
I
OK
I
DD/
I
SS
LU
I
R
PS
T
s
T
a
T
j
Ø
Jc
Ø
JA
UL
FL
MSL
ESD
h
Supply Voltage
[4]
Operating Voltage
[4]
Input Voltage
Output Voltage
DC Output Current
Continuous Clamp Current
Continuous Clamp Current
Continuous current through each V
DD
or V
SS
Latch Up Immunity
Power Supply Ripple
Temperature, Storage
Temperature, Operating Ambient
Temperature, Junction
Dissipation, Junction to Case
Dissipation, Junction to Ambient
Flammability
Moisture Sensitivity
ESD Protection (Human Body Model)
Exceeds spec of
Ripple Frequency < 100 kHz
Non-functional
Functional
Functional
Mil-Spec 883E Method 1012.1
JEDEC (JESD 51)
By design and verification
By design and verification
2000
22.23
74.52
V–0
MSL – 1
–65
0
100
150
+150
+70
165
V
I
< 0 or V
I
> V
SS
V
O
< 0
Description
V
SS
< (V
in
or V
out
) < V
DD
.
Unused inputs must always be tied to an appropriate logic
voltage level (either V
SS
or V
DD
).
Condition
Non-functional
Functional
Relative to V
SS
Relative to V
SS
Min.
2.3
2.3
0
Max.
2.7
2.7
V
DD
V
DDQ
±50
±50
–50
±100
Unit
VDC
VDC
VDC
VDC
mA
mA
mA
mA
mA
mVp-p
°C
°C
°C
°C/W
°C/W
Grade
Grade
V
Table 1. DC Electrical Specifications
(V
DD
= Temperature = 0°C to +85 °C)
Parameter
V
DD
V
DDQ
V
REF
V
TT
V
IH
V
IL
V
OL
Supply Voltage
Description
PC1600,2100,2700
PC3200
Condition
Min.
2.5
2.5
1.25
V
REF
–
40 mV
RESET
RESET
V
DD
/V
DDQ
= 2.3V to 2.7V, I
OL
=
100 A, V
DD
= 2.3 to 2.7V
V
DD
/V
DDQ
= 2.3V, I
OL
= 16 mA,
V
DD
= 2.3V
1.7
0.7
0.2
0.35
Typ.
2.6
2.6
1.3
Max.
2.7
2.7
1.35
Unit
V
V
V
V
V
V
V
Output Supply Voltage PC1600,2100,2700
PC3200
Reference voltage
(V
REF
= V
DDQ
/2)
Termination voltage
Input Voltage, High
Input Voltage, Low
Output Voltage, Low
PC1600,2100,2700
PC3200
V
REF
V
REF
+4
0 mV
Notes:
1. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
2. Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended period may affect reliability.
3. All terminals except V
DD
.
4. V
DD
/V
DDQ
terminals.
Rev 1.0, November 21, 2006
Page 3 of 7
CY2SSTV16857
Table 1. DC Electrical Specifications
(V
DD
= Temperature = 0°C to +85 °C) (continued)
Parameter
V
OH
Description
Output Voltage, High
Condition
V
DD
/V
DDQ
= 2.3V to 2.7V, I
OH
=
–100 A, V
DD
=2.3 to 2.7V
V
DD
/V
DDQ
= 2.3V, I
OH
= –16 mA
I
IL
Input Current
Data Inputs
V
I
= 1.7V or 0.8V, V
REF
= 1.15V or
1.35V, V
DD
= 2.7V
V
I
= 2.7V or 0,V
REF
= 1.15V or
1.35V, V
DD
= 2.7V
V
I
= 1.7V or 0.8V, V
REF
= 1.15V or
1.35V, V
DD
= 3.6V
V
I
= 2.7V or 0
CLK, CLK
V
I
= 1.7V or 0.8V, V
REF
= 1.15V or
1.35V
V
I
= 2.7V or 0, V
REF
= 1.15V or
1.35V, V
dd
= 2.7V
RESET
VREF
I
IH
I
DD
Input Current, High
Dynamic Supply Current
V
I
= V
DD
or V
SS
, V
DD
= 2.7V
V
I
= 1.5V or 1.35V, V
DD
= 2.7
Data inputs only
V
I
= 1.7V or 0.8V, I
O
= 0, V
DD
=
2.7V
V
I
= 2.7V or 0, I
O
= 0, V
DD
= 2.7V
C
in
Input pin capacitance
RESET
Clock and Data Inputs
L
pin
Pin Inductance
All
V
I
= 1.7V or 0.8V, I
O
= 0, V
DD
=
2.7V
2.5
2.1
3
2.7
3.5
4.5
pF
pF
nH
90
90
±5
±5
±5
±5
±1
±1
±5
±5
A
A
A
A
A
A
A
A
mA.
mA
mA
Min.
V
DD
–
0.2
1.95
Typ.
Max.
Unit
V
Table 2. AC Input Electrical Specifications
(V
DD
= 2.5 VDC ± 5%, Temperature = 0°C to +85°C)
V
DD
= 2.5V ± 0.2V
Parameter
F
IN
P
W
T
ACT
T
INACT
T
SET
Description
Input Clock Frequency
Pulse Duration
Differential Inputs Active Time
CLK, CLK
CLK, CLK HIGH or LOW
Data inputs must be LOW after RESET HIGH
3.3
22
22
0.75
0.9
0.75
0.9
360
Condition
Min.
Max.
200
Unit
MHz
ns
ns
ns
ns
ns
ns
ns
mV
Differential Inputs Inactive Time Data and clock inputs must be held at valid levels (not
floating) after RESET LOW
Set-up Time
Fast slew rate, (see notes 5 and 7), Data before CLK,
CLK
Slow slew rate, (see notes 6 and 7), Data before CLK,
CLK
T
HOLD
I
Vpp
Hold Time
Input Voltage, Pk–Pk
Fast slew rate, (see notes 5 and 7), Data after CLK, CLK
Slow slew rate (see notes 6 and 7), Data after CLK, CLK
Notes:
5. For data signal input slew rate > 1 V/ns.
6. For data signal input slew rate > 0.5 V/ns and < 1 V/ns.
Abstract: This paper mainly introduces the performance characteristics of the MSP430F449 single-chip microcomputer. Combined with the typical application of the pre-dual-mode divider SAB6456A and the ...
The PC sends 5 bytes of data to the microcontroller at a time, but when I check the array variables during simulation , they are not correct, and the array pointer is also wrong. Can you experts tell ...
This series of documents would like to thank forum members wstt, david_lee, cat3902982, sugerlatu, zhangdaoyu and other friends for their strong support. They spent a lot of time and energy to organiz...
The digital tube can only display the tens digit and cannot display the ones digit. If you have flickering phenomenon, please give me some advice! ! ! void display(uchar k){uchar shi,ge;shi=k/10;ge=k%...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
Images in science fiction movies often break through the limits of reality, such as in the movie "Minority Report." Tom Cruise uses a multi-touch screen to browse information. Capacitive sensing te...[Details]
A multi-point temperature control heating control system was designed using the SST89E564RC single-chip microcomputer and a new temperature measuring device. The heating system can be controlled in...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
