The RF2314 is a general purpose, low-cost, high performance amplifier
designed for operation from a 2.7V to 6V supply with low current con-
sumption. The circuit configuration with resistive feedback allows for
broadband cascadable amplification. Feedback with capacitive compen-
sation extends the bandwidth of the amplifier, and is designed for opti-
mized noise figure. The device is unconditionally stable and internally
matched to 50Ω. No external components are required. The RF2314 is
available in a very small industry-standard SOT 5-lead surface mount
package, enabling compact designs which conserve board space.
Ordering Information
RF2314
RF2314PCBA-41X
General Purpose Low Noise Amplifier
Fully Assembled Evaluation Board
Optimum Technology Matching® Applied
GaAs HBT
GaAs MESFET
InGaP HBT
SiGe BiCMOS
Si BiCMOS
SiGe HBT
GaAs pHEMT
Si CMOS
Si BJT
GaN HEMT
RF MICRO DEVICES®, RFMD®, Optimum Technology Matching®, Enabling Wireless Connectivity™, PowerStar®, POLARIS™ TOTAL RADIO™ and UltimateBlue™ are trademarks of RFMD, LLC. BLUETOOTH is a trade-
I collected a Ycbcr image from the camera, but I didn't know how to display it, so I converted it to RGB. Now that it has been converted to an RGB image, I want to see if it is collected correctly, so...
We are looking for people with experience in LED control card (synchronous or asynchronous card) projects. We will provide preferential treatment. Full-time or part-time is acceptable. Full-time will ...
I'm a newbie and now I'm facing a problem. I'm using SPI to send 64-bit data continuously. After a long time, there are always interruptions in the middle. I'd like some help from an expert!...
[size=3]Since I had a holiday a few days ago, I just got the board today. I couldn't wait to power it on and test it. [/size][size=3]Let's take a look at some photos first: [/size]Board photos:The ove...
The reference design scheme introduced is a flyback adapter reference design with a maximum output of 9V 5A. The scheme adopts the high-efficiency active clamp flyback controller UCC28780 and the seco...
Emergency hand-held lamps powered by 6V maintenance-free batteries are widely used in rural areas. The charger used is a transformer step-down and single diode half-wave rectifier, and the charging...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
1. Introduction to CIF Board
Fieldbus integration based on PC system
Whether it is a master or a slave, fieldbus has won unanimous praise in the field of PC-based automation. For more...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
This article will introduce a design method for a distributed control system used in a tracking car, which can perform distributed control of motor modules, sensor modules, and lighting control mod...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]