BCW128-1529-12CB95 datasheet, PDF

Datasheet> All Categories > The connector> socket> BCW128-1529-12CB95

BCW128-1529-12CB95: DescriptionIC Socket, BGA128, 128 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size1MB，8 Pages; ManufacturerActel; Websitehttp://www.actel.com/; Environmental Compliance

Download Datasheet Parametric View All

BCW128-1529-12CB95 Overview

IC Socket, BGA128, 128 Contact(s), ROHS COMPLIANT

BCW128-1529-12CB95 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
Contact to complete cooperation	GOLD/TIN
Contact completed and terminated	GOLD/TIN
Contact material	BERYLLIUM COPPER
Device slot type	IC SOCKET
Type of equipment used	BGA128
Shell material	CERAMIC
JESD-609 code	e4/e3
Manufacturer's serial number	BCW
Number of contacts	128
Base Number Matches	1

Preview

Download Datasheet

View All

Socket Mounting Recommendations and Reflow Profile

Purpose

This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)

sockets to the printed circuit board (PCB). The recommendations described here are guidelines

only, and modifications may be needed for your particular socket, PCB, and process.

Application

The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist

Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-

pin technology. This technology allows the pins to be soldered to the PCB while still providing

compliance to the device under test (DUT) via springs located at the other end of the pin. The

pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the

sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or

any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating

Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder

paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil

is required. Once the paste has been applied, a standard reflow process is then used to solder the

socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,

the system is then ready to be used.

Locating Pegs

Although designed to mount to the same footprint as the IC, with just a small amount of

additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are

typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.

These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s

pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs

to be soldered to the PCB for better mechanical stability during everyday use and handling of the

socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-

pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints

may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M

Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is

required to ensure mechanical and electrical integrity. Recommended stencil dimensions are

given in the next section of this document.

E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland

Phone +41-21-781 08 10 ·

www.e-tec.com

info@e-tec.com

E-tec Socket Mounting Recommendations

PRELIMINARY

Recommended Resources

Overload protection circuit for high-voltage motors

High frequency multivibrator circuit

Constant current charging circuit

2's complement input decimal display circuit

Multiple motor windings are connected in series to an electric drying circuit

Computer motherboard circuit diagram 810 2_15

After returning from Xinjiang, I can finally access the Internet.: I was on a business trip to Xinjiang and had no internet or text messages. It was so painful. I'm finally back....; yaoniming3k Mobile and portable

AD Design Tips: Mirror flip componentIt’s actually pretty simple, but there are a few things to note: 1. Switch the input method to English!!! 2. When the device is selected, hold down the left mouse button, the mous...; 小魏哥哥 PCB Design

About USB synchronization issues under WINCE: After I downloaded NK (using HIVE registry) and started it for the first time, WINCE could sync with PC and file access was normal. But when I turned off the power and restarted, it sometimes could no...; guowangguo Embedded System

This week's highlights: [b][url=http://www.deyisupport.com/blog/b/fully_charged/archive/2016/11/11/52584.aspx]Protecting the battery is not as hard as you think[/url][/b][font=微软雅黑][size=3][color=#000000] [/color][/size][/fo...; 橙色凯 Analogue and Mixed Signal

【Video Sharing】Demonstration of Electronic Design Competition Works: [i=s]This post was last edited by paulhyde on 2014-9-15 08:53[/i] Automotive Multifunctional Protection System (2008 Guangdong University Student Electronic Design Competition) [flash]http://www.tudou...; open82977352 Electronics Design Contest

High-speed multi-channel synchronous DSP data acquisition system: TMS320C2XX is a low-cost, high-performance 16-bit fixed-point DSP launched by TI after TMS320C2X and TMS320C5X. The architecture design of TMS320C2XX is based on TMS320C5X. It has the following featur...; Aguilera DSP and ARM Processors

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components