EEWORLDEEWORLDEEWORLD

Part Number

Search

911N-1-106-36

Description
Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, Solder Terminal
CategoryThe connector    The connector   
File Size186KB,2 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

911N-1-106-36 Overview

Board Connector, 6 Contact(s), 1 Row(s), Male, Straight, Solder Terminal

911N-1-106-36 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Reach Compliance Codeunknown
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD FLASH (5) OVER PALLADIUM NICKEL (15)
Contact completed and terminatedTIN LEAD (200) OVER NICKEL (150)
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
DIN complianceNO
Filter functionNO
IEC complianceNO
JESD-609 codee0
MIL complianceNO
Manufacturer's serial number911N
Mixed contactsNO
Installation methodSTRAIGHT
Installation typeBOARD
Number of rows loaded1
OptionsGENERAL PURPOSE
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts6
UL Flammability Code94V-0
Base Number Matches1
How to increase the AD sampling frequency when developing MSP430F5529 on energia?
Now I can only sample sine waves of about 2HZ. If the frequency increases, the points collected will be very few. Please help: Cry:...
821726034 Microcontroller MCU
If implemented with a single-chip microcomputer + DA, if you want to simulate the output of a lithium battery, should you directly connect the DA output in series?
[backcolor=rgb(238, 238, 238)][font=宋体][size=3]As the title says, if we use a single-chip microcomputer + DA to simulate the output of a lithium battery, should we directly connect the DA output in se...
chenweigang MCU
PDA development advice
I use EVC to develop PDA. Are there any special requirements for PDA? Is it like ordinary PDAs such as HP and DELL, or must I use PDA for secondary development? In addition, if I use HP HX2490C PDA, c...
miko2007 Embedded System
Verilog assign usage 2
2)module assign_test ( clk, lhold, lholda );input clk; input lhold; output lholda;reg lholda_r; always @(posedge clk) if (lhold) lholda_r=lhold; else lholda_r=0; assignlholda=lholda_r;endmodule...
eeleader-mcu FPGA/CPLD
Weekly plan submission
Beaglone peripheral circuit design...
billjing DSP and ARM Processors
Sensortag -W3- I2C address of each sensor chip
To obtain the values of each sensor under sensortag, including some important calibration values, they are all obtained through the I2C interface of 2541. If you don't want the data sent back by senso...
johnrey Wireless Connectivity

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1438  1084  2638  831  1657  29  22  54  17  34 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号