SMP75-2-N-A-I-L-TL datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> relay> SMP75-2-N-A-I-L-TL

SMP75-2-N-A-I-L-TL: DescriptionRF Coaxial Relay, SPDT, Latched, 5750mW (Coil), 3000MHz, AC Input, AC Output, Panel Mount,; CategoryMechanical and electronic products relay; File Size96KB，1 Pages; ManufacturerRLC Electronics Inc

Download Datasheet Parametric View All

SMP75-2-N-A-I-L-TL Overview

RF Coaxial Relay, SPDT, Latched, 5750mW (Coil), 3000MHz, AC Input, AC Output, Panel Mount,

SMP75-2-N-A-I-L-TL Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	TNC, BUILT-IN TTL DRIVER AND INDICATOR
body width	26.16 mm
body height	54.86 mm
Body length or diameter	89.92 mm
Characteristic impedance	75 Ω
Coil current (AC) maximum value	0.05 A
Coil power	5750 mW
Maximum coil voltage (AC)	115 V
Coil/Input Power Type	AC
Contact/Output Power Type	AC
Electrical life	1000000 Cycle(s)
Maximum insertion loss	0.2 dB
Maximum isolation	60 dB
Manufacturer's serial number	SMP
Installation features	PANEL MOUNT
Maximum operating frequency	3000 MHz
Minimum operating frequency
physical size	89.92mm X 26.16mm X 54.86mm
Relay action	LATCHED
Relay function	SPDT
Relay type	RF COAXIAL RELAY
surface mount	NO
switching time	20 ms
Termination type	CONNECTOR
voltage standing wave ratio	1.25
Base Number Matches	1

Preview

Download Datasheet

View All

High Power Coaxial Switches

RLC Electronics' High Power Coaxial Switch is a single pole,

two position type providing extremely high reliability, long life

and excellent electrical performance over the frequency range

of DC-6 GHz. The switches will handle 2000 Watts at 100 MHz

to 400 Watts at 6 GHz. The switches utilize thermally conductive,

dielectric insulators to allow high power handling capabilities.

The package utilizes high density packaging techniques, volume

of the switch is less than 6 cubic inches.

Specifications

P-2

-2-3-4-5-6

Switch Type

Frequency Range

DC-4.0

Insertion Loss (Max dB)

VSWR (Max)

Isolation (dB)

0.2

1.25

SINGLE POLE TWO POSITION

DC-6 GHz

4.0-6.0

0.5

1.5

Power Rating, RF Cold Switching:

See page 5.

Impedance:

50 Ohms/75 Ohms.*

Operating Power 25°C:

(Failsafe):

12Vdc at 575 ma nom. 28Vdc at

200 ma nom. 115 Vac at 50 ma nom.

(Latching):

12 Vdc at 1 amp nom. 28 Vdc at

430 ma nom. 115 Vac at 50 ma nom. Current

applied 10 ms min. cutthroat circuitry(standard),

recovery time 100 ms nom.

Connectors, RF:

N, SC, HN, TNC, Female

(HN not recommended for use above 4GHz)

Connectors, Power:

Feed through solder lugs.

Life:

1,000,000 operations.

Switching Time:

20 mS Max.

Weight:

12 oz.

Environmental Conditions:

MIL-S-3928

Operating Mode:

Manual, failsafe or latching.

Switching Sequence:

Break before make.

*75 ohm up to 3 GHz.

To designate the switch desired use:

(1) “M” for Manual, “R” for Remote.

(2) “S” for SC, “H” for HN, “N” or “T” for TNC

(3) “A” for 115 Vac, “D” for 28 Vdc or “H” for 12 Vdc.

(4) “I” for indicators if desired.

(5) “L” for latching cutthroat if desired.

(6) “TL” for TTL Driver if desired

Example: SRP-2-S-D-I is a remote, SC Connectors, 28 Vdc; with indicators, Failsafe operation switch 50 ohms

for 75 ohms SRP75-2- - -

Outline Drawing

RLC ELECTRONICS, INC.

83 Radio Circle, Mount Kisco, New York 10549 • Telephone: 914-241-1334 • Fax: 914-241-1753

e-mail: sales@rlcelectronics.com • www.rlcelectronics.com

Recommended Resources

Advanced recording deck circuit

New micropower low dropout voltage regulator application circuit 05

LA6520 audio IC amplifier circuit diagram

Practical music massager and doorbell dual-purpose circuit

Frequency sensitive rheostat starting control circuit

Heart rate monitor circuit diagram

Oscilloscope measurement and waveform analysis of intake air pressure sensor signal in auto repair: The intake pressure sensor is the intake manifold pressure sensor. It is used in the D-type electronic fuel injection system (the L-type uses an air flow meter to detect the intake volume). The intake...; Micsig麦科信 Automotive Electronics

How to choose a network transformer: Usually, a network transformer is added between the Gigabit PHY and RJ45. So how to select this network transformer? What indicators should be paid attention to? Or will any network transformer be fin...; xiaoxiao2211 Analog electronics

Please help me with the questions I encountered during my self-study.: I just started to learn 51 MCU by myself. I watched Guo Tianxiang's "10 Days to Conquer MCU" tutorial and found that he used 89S51 MCU and there was no process of connecting Dupont wires in the video....; liuweisatana 51mcu

Zigbee network topology: According to the instructions in the document, set the network depth, type, number of child nodes, and number of routing nodes, but it is not the desired network structure....; hl5286 RF/Wirelessly

I really don't know how to do this, can someone give me some pointers?: The design requirements of the Thevenin theorem equivalent model tester: ① The test model and parameters are displayed in a graphical manner through a graphic LCD. ② The equivalent voltage source is a...; 看客 Analog electronics

PCB cooling: Can someone explain to me, in addition to cooling the PCB board through the fan, can the PCB board be cooled through special components?...; huangdh PCB Design

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components