At +25°C, V± = 15VDC and 15VDC between P+ and P–, unless otherwise specified.
3656AG, BG, HG, JG, KG
PARAMETER
ISOLATION
Voltage
Rated Continuous
(1)
, DC
Test, 10s
(1)
Test, 60s
(1)
Rejection
DC
60Hz,
<
100Ω in I/P Com
(2)
60Hz, 5kΩ in I/P Com
(2)
3656HG
3656AG, BG, JG, KG
Capacitance
(1)
Resistance
(1)
Leakage Current
GAIN
Equations
Accuracy of Equations
Initial
(3)
3656HG
3656AG, JG, KG
3656BG
vs Temperature 3656HG
3656AG, JG
3656BG, KG
vs Time
Nonlinearity
External Supplies Used at
Pins 12 and 16, 3656HG
3656AG, JG, KG
3656BG
Internal Supplies Used for
Output Stage
OFFSET VOLTAGE
(5)
, RTI
Initial
(3)
, 3656HG
3656AG, JG
3656BG, KG
vs Temperature, 3656HG
3656JG
3656AG
3656KG
3656BG
vs Supply Voltage
3656HG
3656AG, BG, JG, KG
vs Current
(6)
vs Time
AMPLIFIER PARAMETERS, Apply to A
1
and A
2
Bias Current
(7)
Initial
vs Temperature
vs Supply
Offset Current
(7)
Impedance
Common-Mode
Input Noise Voltage
f
B
= 0.05Hz to 100Hz
f
B
= 10Hz to 10kHz
Input Voltage Range
(8)
Linear Operation
Internal Supply
External Supply
Output Current
V
OUT
=
±5V
±15V
External Supply
Internal Supply
V
OUT
=
±10V
±15V
External Supply
V
OUT
=
±2V,
V
P+, P–
= 8.5V
Internal Supply
Quiescent Current
CONDITIONS
MIN
TYP
MAX
UNITS
G
1
= 10V/V
3500 (1000)
8000 (3000)
2000 (700)
160
125
108
112
6 (6.3)
10
12
(10
12
)
0.28
VDC
VDC
Vrms
dB
dB
dB
dB
pF
Ω
µA
120V, 60Hz
See Text
G
<
100V/V
0.5
1.5
1
0.3
480
120
60
0.02 (1 + log khrs.)
%
%
%
ppm/°C
ppm/°C
ppm/°C
%
R
A
+ R
F
= R
B
≥
2MΩ
Unipolar or Bipolar Output
±0.15
±0.1
±0.05
±0.15
±[4
+ (40/G
1
)]
±[2
+ (20/G
1
)]
±[1
+ (10/G
1
)]
±[200
+ (1000/G
1
)]
±[50
+ (750/G
1
)]
±[25
+ (500/G
1
)]
±[10
+ (350/G
1
)]
±[5
+ (350/G
1
)]
±[0.6
+ (3.5/G
1
)]
±[0.3
+ (2.1/G
1
)]
±[0.2
+ (20/G
1
)]
%
%
%
%
mV
mV
mV
µV/°C
µV/°C
µV/°C
µV/°C
µV/°C
mV/V
mV/V
mV/mA
Bipolar Output Voltage
Swing, Full Load
(4)
15Vp between P+ and P–
Supply between P+ and P–
±[0.1
+ (10/G
1
)]
±[10
+ (100/G
1
)] •
(1 + log khrs.)
µV
100
0.5
0.2
5
100 || 5
5
5
20
nA
nA/°C
nA/V
nA
MΩ || pF
µVp-p
µVrms
V
V
mA
mA
mA
±5
Supply –5
±5
±2.5
±2.5
±1
150
450
mA
µA
®
3656
2
SPECIFICATIONS
ELECTRICAL
(CONT)
At +25°C, V± = 15VDC and 15VDC between P+ and P–, unless otherwise specified.
3656AG, BG, HG, JG, KG
PARAMETER
FREQUENCY RESPONSE
±3dB
Response
Full Power
Slew Rate
Settling Time
OUTPUT
Noise Voltage (RTI)
Residual Ripple
(9)
POWER SUPPLY IN, at P+, P–
Rated Performance
Voltage Range
(10)
Ripple Current
(9)
Quiescent Current
(11)
Current vs Load Current
(12)
CONDITIONS
Small Signal
Direction Measured at Output
to 0.05%
f
B
= 0.05Hz to 100Hz
f
B
= 10Hz to 10kHz
+0.1, –0.04
500
√(5)
2
+ (22/G
1
)
2
√(5)
2
+
(11/G
1
)
2
5
15
Derated Performance
Average
vs Current from +V, –V, V+, V–
8.5
7
8.5
10
14
0.7
9
8
0.66
40
80
–25
0
–55
–65
16
25
18
MIN
TYP
30
1.3
MAX
UNITS
kHz
kHz
V/µs
µs
µVp-p
µVrms
mVp-p
VDC
VDC
mAp-p
mA/DC
mA/mA
V
V
V/V
mVp-p
mVp-p
°C
°C
°C
°C
ISOLATED POWER OUT, At +V, –V, V+, V– pins
(13)
Voltage, No Load
15V Between P+ and P–
Voltage, Full Load
±5mA
(10mA sum) Load
(12)
Voltage vs Power Supply
vs Supply Between P+ and P–
Ripple Voltage
(9)
No Load
Full Load
±5mA
Load
TEMPERATURE RANGE
Specification 3656AG, BG
3656HG, JG, KG
Operation
(10)
Storage
(14)
9.5
9
200
+85
+70
+100
+125
NOTES: (1) Ratings in parenthesis are between P- (pin 20) and O/P Com (pin 17). Other isolation ratings are between I/P Com and O/P Com or I/P Com and P–.
(2) See Performance Curves. (3) May be trimmed to zero. (4) If output swing is unipolar, or if the output is not loaded, specification same as if external supply were used.
(5) Includes effects of A
1
and A
2
offset voltages and bias currents if recommended resistors used. (6) Versus the sum of all external currents drawn from V+, V–, +V,
–V (= ISO). (7) Effects of A
1
and A
2
bias currents and offset currents are included in Offset Voltage specifications. (8) With respect to I/P Com (pin 3) for A
1
and with
respect to O/P Com (pin 17) for A
2
. CMR for A
1
and A
2
is 100dB, typical. (9) In configuration of Figure 3. Ripple frequency approximately 750kHz. Measurement bandwidth
is 30kHz. (10) Decreases linearly from 16VDC at 85°C to 12VDC at 100°C. (11) Instantaneous peak current required from pins 19 and 20 at turn-on is 100mA for slow
rising voltages (50ms) and 300mA for fast rises (50µs). (12) Load current is sum drawn form +V, –V, V+, V– (= I
ISO
). (13) Maximum voltage rating at pins 1 and 4 is
±18VDC;
maximum voltage rating at pins 12 and 16 is
±18VDC.
(14) Isolation ratings may degrade if exposed to 125°C for more than 1000 hours or 90°C for more than 50,000
hours.
Example of the ratings for 3-port continuous isolation.
20
PACKAGE INFORMATION
PRODUCT
3656
PACKAGE
20-Lead ISO Omni
PACKAGE DRAWING
NUMBER
(1)
102A
3500VDC
3
1000VDC
3500VD
C
17
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
PIN DESIGNATIONS
NO.
1
2
3
4
5
6
7
8
9
10
DESCRIPTION
+V
MOD Input
Input DEMOD COM
–V
Balance
A
1
Inverting Input
A
1
Noninverting Input
Balance
A
1
Output
Input DEMOD
NO.
11
12
13
14
15
16
17
18
19
20
DESCRIPTION
Output DEMOD
V–
A
2
Noninverting Input
A
2
Inverting Input
A
2
Output
V+
Output DEMOD COM
No Pin
P+
P–
ABSOLUTE MAXIMUM RATINGS
Supply Without Damage ...................................................................... 16V
Input Voltage Range Using Internal Supply .........................................
±8V
Input Voltage Range Using External Supply ................................... Supply
RT, I want to communicate between the microcontroller and the smart bracelet. The smart bracelet uses the CC2640 chip and follows the Bluetooth HID protocol. The smart bracelet is the host, and the mi...
I am looking for an algorithm for displaying images in wince at a high price. The images are png and jpg. If you are interested, please contact QQ: 32757309 and indicate the source. Thank you....
[i=s]This post was last edited by Hot Ximixiu on 2020-10-10 20:21[/i]Clock image
Set the main clock source/************************************************************************** Function name: CLO...
I just won two prizes in the "TE helps data center design, shortening the distance between you and the Olympics" event. The second time I won a Xiaomi smart socket. Haha, let me show off my luck!!! :p...
I was very excited when I got the board at school at noon. I studied the board and found that the OLED uses a voltage of 15V; there is an LC4032V programmable controller produced by Lattice on the boa...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
Wireless Connectivity
京公网安备 11010802033920号
EEWORLD
