EEWORLDEEWORLDEEWORLD

Part Number

Search

BD2425N50200A00

Description
2400 MHz - 2500 MHz RF TRANSFORMER
CategoryPower management    transformer   
File Size230KB,6 Pages
ManufacturerAnaren
Websitehttp://www.anaren.com/
Environmental Compliance
Download Datasheet Parametric View All

BD2425N50200A00 Overview

2400 MHz - 2500 MHz RF TRANSFORMER

BD2425N50200A00 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerAnaren
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresHEIGHT DIMENSION INCLUDES TERMINALS ALSO
maximum cutoff frequency2500 MHz
minimum cutoff frequency2400 MHz
high0.65 mm
Insertion loss0.7 dB
JESD-609 codee4
length1 mm
Installation featuresSURFACE MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-55 °C
method of packingTAPE & REEL
physical sizeL1.0XB1.0XH0.65 (mm)
surface mountYES
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Transformer typeRF TRANSFORMER
width1 mm
Base Number Matches1
Model BD2425N50200A00
Rev D
Ultra Low Profile 0404 Balun
50Ω to 200Ω Balanced
Description
The BD2425N50200A00 is a low cost, low profile sub-miniature unbalanced to
balanced transformer designed for differential inputs and output locations on modern
chipsets in an easy to use surface mount package. The BD2425N50200A00 is ideal
for high volume manufacturing and delivers higher performance than traditional
ceramic baluns. The BD2425N50200A00 has an unbalanced port impedance of 50Ω
and a 200Ω balanced port impedance. This transformation enables single ended
signals to be applied to differential ports on modern integrated chipsets. The output
ports have equal amplitude (-3dB) with 180 degree phase differential. The
BD2425N50200A00 is available on tape and reel for pick and place high volume
manufacturing.
Detailed Electrical Specifications:
Specifications subject to change without notice.
Features:
2400 – 2500 MHz
0.65mm Height Profile
50 Ohm to 2 x 100 Ohm
Low Insertion Loss
802.11 b+g
MIMO b+g
Bluetooth
Zigbee
Surface Mountable
Tape & Reel
Non-conductive
RoHS Compliant
Parameter
Frequency
Unbalanced Port Impedance
Balanced Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
CMRR
Power Handling
Operating Temperature
Min.
2400
ROOM (25°C)
Typ.
50
200
27
0.6
0.5
2
29
Max
2500
Unit
MHz
dB
dB
dB
Degrees
dB
Watts
ºC
21
0.7
1.0
6
1
+85
-55
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
Top View (Near-side)
Side View
Bottom View (Far-side)
[
.041
+.003
-.002
1.05
+0.08
-0.06
]
[
.041
+.003
-.002
1.05
+0.08
-0.06
]
.012 [0.30]
.024
±.0025
[0.62
±0.064
] 0.12 [0.30] 1
2
3x.010
[0.25]
4
3
3x.010
[0.25]
4X .020 [0.50]
Pin Designation
GND / DC Feed
1
+ RF GND
Dimensions are in Inches [Millimeters]
Mechanical Outline
2 Unbalanced Port
3 Balanced Port
4 Balanced Port
Tolerances are Non-Cumulative
Available on Tape
and Reel for Pick and
Place Manufacturing.
USA/Canada:
Toll Free:
Europe
:
(315) 432-8909
(800) 411-6596
+44 2392-232392
NEC Cup and 12 articles of National Level 1.pdf
[i=s] This post was last edited by paulhyde on 2014-9-15 08:54 [/i] NEC Cup and 12 National One.pdf...
yelinyimeng Electronics Design Contest
Work choice?
The company (Guangzhou) I work for now has limited room for development. I haven't been promoted in 6 years, and my salary hasn't increased. I used to be a bit stupid (I value dedication and loyalty i...
lxh1985 Embedded System
How does the USB disk filter driver obtain the device descriptor?
I want to make a USB disk filter driver. First, I read the device descriptor of the USB disk, and then disable the USB disk according to a certain item in the device descriptor. Thanks to everyone's h...
norwegianwood Embedded System
STM32 remote upgrade
Today I saw the STM32 remote upgrade solution that uses GPRS for remote upgrade. Now I have used the process on the Internet to set up serial port IAP. First, burn the bootloader firmware on the devel...
常见泽1 stm32/stm8
Compare #define uchar unsigned char with typedef unsigned char uchar
As the title says: Please compare: What is the difference between [b]#define uchar unsigned char[/b] and [b]typedef unsigned char uchar[/b], and what are the advantages and disadvantages?...
jiangliteng Embedded System
A question about the DC millivoltmeter circuit. If you are interested, please come and discuss it.
I think there is something wrong with the installation of the meter in this circuit. It should be installed on the branch of resistor R4. The meter is ready-made, and any current within 1MA can be rea...
lzy63912 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1662  995  1174  2569  121  34  21  24  52  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号