5962-9461003HZC datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9461003HZC

5962-9461003HZC: DescriptionFlash Module, 128KX32, 120ns,; Categorystorage storage; File Size290KB，32 Pages; ManufacturerWhite Microelectronics

Download Datasheet Parametric View All

5962-9461003HZC Overview

Flash Module, 128KX32, 120ns,

5962-9461003HZC Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
Maximum access time	120 ns
JESD-30 code	S-XHIP-P66
JESD-609 code	e4
length	30.1 mm
memory density	4194304 bit
Memory IC Type	FLASH MODULE
memory width	32
Number of functions	1
Number of terminals	66
word count	131072 words
character code	128000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	128KX32
Package body material	UNSPECIFIED
encapsulated code	HIP
Package shape	SQUARE
Package form	IN-LINE
Parallel/Serial	PARALLEL
Programming voltage	5 V
Certification status	Not Qualified
Maximum seat height	5.84 mm
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	NO
technology	CMOS
Temperature level	MILITARY
Terminal surface	GOLD
Terminal form	PIN/PEG
Terminal pitch	2.54 mm
Terminal location	HEX
width	30.1 mm
Base Number Matches	1

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Added case outlines M, N, 4, and 5.

Figure 1; For the case outlines 4 and 5 changed dimension D3 min

and max from 1.030 and 1.040 inches to 1.020 and 1.060 inches.

Changed dimension A min from .156 inches to .135 inches. Changed

dimension L min from .145 inches to .132 inches. -sld

Update drawing to the latest requirements. -sld

DATE (YR-MO-DA)

96-10-15

98-07-08

APPROVED

K. A. Cottongim

06-06-30

Raymond Monnin

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

Gary Zahn

CHECKED BY

Michael C. Jones

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS

AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

AMSC N/A

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil/

APPROVED BY

Kendall A. Cottongim

MICROCIRCUIT, HYBRID, DIGITAL, FLASH,

ERASABLE/PROGRAMMABLE READ ONLY

MEMORY, 128K x 32-BIT

DRAWING APPROVAL DATE

95-01-31

REVISION LEVEL

SIZE

SHEET

CAGE CODE

67268

1 OF

5962-94610

DSCC FORM 2233

APR 97

5962-E417-06

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at

http://assist.daps.dla.mil/quicksearch/

http://assist.daps.dla.mil

or from

the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of

this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in

accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as

designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The

manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as

defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not

affect the form, fit, or function of the device for the applicable device class.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in

MIL-PRF-38534 and herein.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.

3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figure 4, 5, and 6.

3.2.5 Block diagram. The block diagram shall be as specified on figure 7.

3.2.6 Output load circuit. The output load circuit shall be as specified on figure 8.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full specified operating temperature range.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

SIZE

REVISION LEVEL

5962-94610

SHEET

DSCC FORM 2234

APR 97

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are defined in table I.

3.5 Programming procedure. The programming procedure shall be as specified by the manufacturer and shall be

available on request.

3.6 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with

the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.

3.7 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described

herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,

for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those

which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be

made available to the preparing activity (DSCC-VA) upon request.

3.8 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this

drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets

the performance requirements of MIL-PRF-38534 and herein.

3.9 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

microcircuits delivered to this drawing.

3.10 Endurance. A reprogrammability test shall be completed as part of the vendors's reliability monitor. The

reprogrammability test shall be done for the initial characterization and after any design process changes which may affect the

reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the number of

program/erase endurance cycles listed in section 1.3 herein over the full military temperature range. The vendors procedure

shall be kept under document control and shall be made available upon request of the acquiring of preparing activity.

3.11 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This test shall

be done for initial characterization and after any design or process change which may affect data retention. The methods and

procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein over the full military

temperature range. The vendor's procedure shall be kept under document control and shall be made available upon request of

the acquiring or preparing activity.

4. VERIFICATION

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as

modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,

fit, or function as described herein.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

SIZE

REVISION LEVEL

5962-94610

SHEET

DSCC FORM 2234

APR 97

Recommended Resources

Semiconductor self-excited excitation circuit

Add voice control function circuit to electric toys

Cadmium-nickel battery automatic charging and discharging circuit composed of TL082

Positive and negative voltage output circuit diagram

High current, high power amplifier circuit

Infrared remote control switch circuit diagram using phase locked loop audio decoding

Help BQ76925: I am new to power management and I don't understand many things. I am currently doing the most basic voltage and current testing. However, there are six batteries in total, but the fifth battery I mea...; 水说。 Analogue and Mixed Signal

How to update the AD13 schematic diagram to PCB by adding several components: I just started using Altium Designer 13. I added a few capacitors to the schematic. When I used the import update from schematic in PCB, the following error message popped up. What is the reason and h...; 初出茅庐！ PCB Design

LED Backlight Technology: [hide]LED backlight technology is one of the core technologies of the "future" of LCD TV products. Not long ago, Hisense took the lead in launching a 42-inch LCD TV product in the domestic market, whi...; 探路者 LED Zone

Urgent!!! About the problem of calling DirectShow to develop multimedia under WINDOWS CE!!!: I am using DirectShow to develop multimedia on the WINDOWS CE platform. After initializing COM, I always get an error when calling the CoCreateInstance method, and a very small negative number is retu...; 白开水 Embedded System

APWM routine: Could anyone share a routine for using the ECAP module in 28335 as APWM function?...; lzx_18570633112 DSP and ARM Processors

Bootloader Problems with booting wince from sd card: In order to update the wince system conveniently, I want to boot wince on sd, and the bootloader is still on nandflash. I downloaded the bootloader source code from the Internet, the sd card was initi...; fobdwjjatq Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components