EEWORLDEEWORLDEEWORLD

Part Number

Search

4243-00

Description
C Male Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG11, RG225, RG393
CategoryThe connector   
File Size271KB,8 Pages
ManufacturerpSemi (peregrine semiconductor)
Websitehttp://www.psemi.com/
Download Datasheet Compare View All

4243-00 Overview

C Male Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG11, RG225, RG393

Product Specification
PE4243
SPDT UltraCMOS™ RF Switch
Product Description
The PE4243 UltraCMOS™ RF Switch is designed to cover a
broad range of applications from near DC through 3000 MHz.
This reflective switch integrates on-board CMOS control logic
with a low voltage CMOS-compatible control interface, and can
be controlled using either single-pin or complementary control
inputs. Using a nominal +3-volt power supply voltage, a typical
input 1 dB compression point of +27 dBm can be achieved.
The PE4243 UltraCMOS™ RF Switch is manufactured in
Peregrine’s patented Ultra Thin Silicon (UTSi®) CMOS
process, offering the performance of GaAs with the economy
and integration of conventional CMOS.
Figure 1. Functional Diagram
RFC
Features
Single-pin or complementary CMOS
logic control inputs
+3.0-volt power supply needed for
single-pin control mode
Low insertion loss: 0.7 dB at 1000 MHz,
0.9 dB at 2000 MHz
Isolation of 30 dB at 1000 MHz, 21 dB
at 2000 MHz
Typical 1 dB compression point of
+27 dBm
Ultra-small SOT-23 package
Figure 2. Package Type
6-lead SOT-23
RF1
RF2
CMOS
Control
Driver
CTRL CTRL or V
DD
Table 1. Electrical Specifications @ +25 °C, V
DD
= 3 V
(Z
S
= Z
L
= 50
Ω)
Parameter
Operation Frequency
1
Insertion Loss
Isolation
Return Loss
‘ON’ Switching Time
‘OFF’ Switching Time
Video Feedthrough
2
Input 1 dB Compression
Input IP3
2000 MHz
2000 MHz, 14 dBm input power
26
43
1000 MHz
2000 MHz
1000 MHz
2000 MHz
1000 MHz
2000 MHz
50% CTRL to 0.1 dB of final value, 1 GHz
50% CTRL to 25 dB isolation, 1 GHz
28
19
18
16
Conditions
Minimum
DC
Typical
0.7
0.9
30
21
22
19
300
200
15
27
45
Maximum
3000
0.85
1.05
Units
MHz
dB
dB
dB
dB
dB
dB
ns
ns
mV
pp
dBm
dBm
Notes: 1. Device linearity will begin to degrade below 10 MHz.
2. The DC transient at the output of any port of the switch when the control voltage is switched from Low to High or High to Low in a 50
test
set-up, measured with 1ns risetime pulses and 500 MHz bandwidth.
Document No. 70-0096-02
www.psemi.com
©2005 Peregrine Semiconductor Corp. All rights reserved.
Page 1 of 8

4243-00 Related Products

4243-00 4243 PE4243 PE4243-EK
Description C Male Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG11, RG225, RG393 C Male Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG11, RG225, RG393 C Male Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG11, RG225, RG393 C Male Connector Clamp/Solder Attachment For RG213, RG214, RG8, RG9, RG11, RG225, RG393
Watch for the MSP-EXP430FR5739 Kit
I am a novice in MSP430 microcontrollers. I am preparing to learn it due to work reasons. I missed the LaunchPad some time ago and I regret it very much. Now I urgently need an MSP430 board and hope t...
yuejunwei1989 Microcontroller MCU
Stopwatch, hope you guys can give me some advice
The title of the course project I did this time is: Use 8051 to make a stopwatch, controlled by a button. Press it for the first time to start timing, press it for the second time to stop, press it fo...
12301230 MCU
How does Allegro's built-in package library identify which type of device it belongs to?
In the package library that comes with Allegro, CAP400 and CAP300 are different packages for capacitors, and RES500 and RES600 are different packages for resistors. The question I want to ask is, in t...
ujs PCB Design
Component packaging
MAXIN component packaging...
你妹 PCB Design
Is there any difference between vs1001k and vs1003?
Since vs1001k is too expensive, I want to use vs1003 instead. Is there any problem? What is the difference between the two? Is there any difference in programming between the two? I hope someone who h...
37°男人 Analog electronics
A simple question about the multiplexer, please help
There are three frequency signals (approximate square wave amplitude of 3V with different frequencies, frequency range 1Khz-100Khz), I want to do a three-choice process, that is, the microcontroller c...
mazzz Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2789  1142  2855  2234  2221  57  23  58  45  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号