Thermal Cutouts
Temperature Protection for Electronics
ADVANTAGES
– broad product range for many applications
and loads
– widest selection of connections and housings
– minimal contact resistance
E-Type
DESCRIPTION
Types E 05, E 11, E 15, E 16, E 18, E 21, E 22, E 23 and E 26 are
thermal cutouts.
Within limits they can also be used as temperatu-
re regulators.
A bimetal snap disc with single or double contact opens or closes an
electric circuit when reaching a pre-set temperature. Reset follows
after a substantial drop in temperature.
Heat transfer from all sides results from heat conduction or radiation
onto the base of the housing.
Standard version: aluminium, black anodised.
DIMENSIONS
E 05 (Standard)
E 11 (Standard)
E 18 (Standard)
E 21 (Standard)
02-04-01
1000-Y133
CANTHERM
8415 Mountain Sights Avenue • Montreal (Quebec), H4P 2B8, Canada
Tel: (514) 739-3274 • 1-800-561-7207 • Fax: (514) 739-290
E-mail : sales@cantherm.com • Website: www.cantherm.com
APPLICATIONS
Temperature monitoring, control and signalling in
electronic and electrical equipment.
Examples:
Electronic components such as transistors,
thyristors, diodes, triacs
Power resistors
Heat sinks
Printed circuits
Amplifiers
Projectors
Electrical machinery and apparatus
Generating sets
Heat exchangers
Plastic and metal housings
TECHNICAL DATA
Type
Voltage rating* 50 – 60 Hz*
Current rating cos
ϕ
= 1,0*
Current rating cos
ϕ
= 0,6*
Max. load
at cos
ϕ
= 1,0
without damage
E 05 / E23
250 V
2.0 A
1.2 A
RESPONSE TEMPERATURES
When selecting the response temperature, the hea-
ting and cooling characteristics of the housing
should be considered. Temperature testing is carried
out with a rate of rise 0.1 °C/min.
For cutout types E 05, E 11 and E 18 with response
temperatures under 71 °C, the published electrical
loading should be reduced by upto 50 %, as these
types are current sensitive.
Close tolerances on the response temperature or
reset temperature, as well as smaller differentials
are all possible on request.
Reset differential as standard is between 10 °C and
50 °C. Minimum rate of temperature change 0.1
K/min.
E 15 / E 16
250 V
2.0 A
1.6 A
E 11 / E 18 / E 21 / E 22 / E 26
250 V
6.3 A
4.0 A
250 V AC
110 V AC
60 V DC
42 V DC
6/12/24 V DC
3.0 A
3.5 A
0.6 A
0.8 A
1.0 A
6.3 A
8.0 A
1.0 A
1.2 A
1.5 A
10.0 A
12.0 A
3.0 A
4.2 A
5.5 A
Contact arrangement
Switching operations
at rated current*
Contact resistance
Dielectric strength
across open contacts
Response temperature range
Standard tolerance
Dielectric strength
housing to earth
Test Class I
< 60 mΩ
650 V
eff
50 Hz
from +80 °C to
+150 °C
(353 to 423 K)
±3 K ±5 K ±10 K
Test Class I
< 60 mΩ
1500 V
eff
50 Hz
from +50 °C to
+150 °C
(323 to 423 K)
±3 K ±5 K ±10 K
P 300
P 301
P 302
P 303
P 304
500 V
eff
50/60 Hz
1000 V
eff
50/60 Hz
2000 V
eff
50/60 Hz
2500 V
eff
50/60 Hz
4000 V
eff
50/60 Hz
150 °C
3 g (vibration proof)
sealed against external elements e. g. dust oil, lacquer, resin et
Leads
0,25 mm
2
(AWG 24)
black
F 11
Leads
T 11 normally closed 0.5 mm
2
(AWG 22), yellow
T 10 normally open 0.25 mm
2
(AWG 24), black
normally closed T 11 / normally open T 10
Leads
0,6 mm
2
(AWG 22)
yellow
B11
Test Class I
< 60 mΩ
1000 V
eff
50 Hz
from +50 °C to
+150 °C
(323 to 423 K)
±3 K ±5 K ±10 K
Max. continuous temperature
Possible acceleration
Protection
Connections
standard
Switch element
Note: *Approved ratings – Other values on request.
INSTALLATION HINTS
It is important to ensure good heat transfer to the cu-
tout: it should be placed directly onto the heat sour-
ce.
Housings are voltage-free (except G 800) and can
be installed without additional insulation.
The cutouts can be attached to metal surfaces or
housings and, depending on the exact version, can
be screwed, clipped, clamed or soldered on.
G 800 version can be positioned direct onto a circuit
board.
02-04-01
1000-Y133
HOUSINGS
Style
G 254
G 700
G 701
G 702
G 703
G 707
G 711
G 714
G 716
G 718
G 722
G 723
G 724
G 726
Description
E 18
E 05
E 05
E 05
E 11
E 11
E 11
E 21
E 21
E 11
E 18
E 18
E 18
E 11
E 05
E 11
E 21
Ø 16x4,8
M4x6
Al black
SW 16x4,8
M4x10
Al black
SW12x4,8
M4x5
CuZn
Ø 12x3,5
Ø 16x4,8
Ø 15,7x4,4
M4x6
M4x6
M5x6
CuZn
Al black
CuZn
Ø 16x5
SW10x3,7
M4x6
Al black
Al black
as E 18
but without mounting flange
threaded stud mounting
as E 05 G 800
however only 1 wire connection Ø 1.5
threaded stud mounting
threaded stud with solid
wire leads
central fixing
as G 703
but with leads
threaded stud
as G 703
but with 2.8x0.5 tabs
threaded stud and
leads
as E 18
but with narrow flange
as E 18
but with 2.8x0.5 tabs
as E 18
but with narrow flange and 2,8x0,5 tabs
threaded stud and
leads
tinned Cu lead wires
G 800
02-04-01
1000-Y133
SPECIAL CONNECTIONS
Leads or single wire from 0,25 mm
2
to 1,0 mm
2
,
Lengths from 40 mm to 10 000 mm with or with-
out stripped ends. Leads fitted with DIN push-on
terminations or crimp connectors. Freon or oil re-
sistant leads, or PTFE, PVF
2
, Nomex or Silicone
leads available from stock.
IMPORTANT
Leads are specified according to insulation class
and dielectric strength.
MARKING
Response temperature in clear text (5 °C steps).
Normally closed = blue (epoxy)
Normally open = red (epoxy)
Special markings available on request.
APPROVALS
Life expectancy, nominal voltage and current ra-
tings according to VDE 0631 or EN 60730. Fur-
ther approvals – Information on request.
STANDARD QUALITY
Production item testing
Voltage test, Switch function test,
Nominal switching temperature.
ORDERING INFORMATION
Quality
100
Type
E 11
temperature
125 °C ±10 K
Version
G 703
We reserve the right to change specifications without prior notice.
CANTHERM
8415 Mountain Sights Avenue • Montreal (Quebec), H4P 2B8, Canada
Tel: (514) 739-3274 • 1-800-561-7207 • Fax: (514) 739-290
E-mail : sales@cantherm.com • Website: www.cantherm.com
京公网安备 11010802033920号
EEWORLD
