531QB95M0000DGR datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 531QB95M0000DGR

531QB95M0000DGR: DescriptionCMOS/TTL Output Clock Oscillator, 95MHz Nom, ROHS COMPLIANT, SMD, 6 PIN; CategoryPassive components oscillator; File Size215KB，12 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric View All

531QB95M0000DGR Overview

CMOS/TTL Output Clock Oscillator, 95MHz Nom, ROHS COMPLIANT, SMD, 6 PIN

531QB95M0000DGR Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT, SMD, 6 PIN
Reach Compliance Code	unknown
Other features	TAPE AND REEL
maximum descent time	0.35 ns
Frequency Adjustment - Mechanical	NO
frequency stability	20%
JESD-609 code	e4
Manufacturer's serial number	531
Installation features	SURFACE MOUNT
Nominal operating frequency	95 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Oscillator type	CMOS/TTL
physical size	7.0mm x 5.0mm x 1.85mm
longest rise time	0.35 ns
Maximum supply voltage	3.63 V
Minimum supply voltage	2.97 V
Nominal supply voltage	3.3 V
surface mount	YES
maximum symmetry	55/45 %
Terminal surface	Nickel/Gold (Ni/Au)
Base Number Matches	1

Preview

Download Datasheet

View All

S i 5 3 0 / 5 31

EVISION

R Y S TA L

S C I L L A T O R

(XO)

(10 M H

Z T O

1.4 G H

)

Features

Available with any-rate output

frequencies from 10 MHz to 945 MHz

and select frequencies to 1.4 GHz

3rd generation DSPLL

with superior

jitter performance

3x better frequency stability than

SAW-based oscillators

Internal fixed crystal frequency

ensures high reliability and low

aging

Available CMOS, LVPECL,

LVDS, and CML outputs

3.3, 2.5, and 1.8 V supply options

Industry-standard 5 x 7 mm

package and pinout

Pb-free/RoHS-compliant

Si5602

Ordering Information:

See page 7.

Applications

SONET/SDH

Networking

SD/HD video

Test and measurement

Clock and data recovery

FPGA/ASIC clock generation

Pin Assignments:

See page 6.

(Top View)

GND

Description

The Si530/531 XO utilizes Silicon Laboratories’ advanced DSPLL circuitry

to provide a low jitter clock at high frequencies. The Si530/531 is available

with any-rate output frequency from 10 to 945 MHz and select frequencies to

1400 MHz. Unlike a traditional XO, where a different crystal is required for

each output frequency, the Si530/531 uses one fixed crystal to provide a

wide range of output frequencies. This IC based approach allows the crystal

resonator to provide exceptional frequency stability and reliability. In addition,

DSPLL clock synthesis provides superior supply noise rejection, simplifying

the task of generating low jitter clocks in noisy environments typically found in

communication systems. The Si530/531 IC based XO is factory configurable

for a wide variety of user specifications including frequency, supply voltage,

output format, and temperature stability. Specific configurations are factory

programmed at time of shipment, thereby eliminating long lead times

associated with custom oscillators.

CLK–

CLK+

Si530 (LVDS/LVPECL/CML)

GND

Functional Block Diagram

CLK– CLK+

CLK

Si530 (CMOS)

Fixed

Frequency

Any-rate

10–1400 MHz

DSPLL

Clock

Synthesis

GND

CLK–

CLK+

Si531 (LVDS/LVPECL/CML)

GND

Rev. 1.1 6/07

Si530/531

Recommended Resources

555 water level control circuit diagram

Household advance working remote control circuit - transmitter circuit

Proximity sensor circuit diagram

68722 type electrocardiograph circuit

Single tube 0TL power amplifier circuit

Infrared remote control dimmer light

How to achieve communication between driver and application without using DeviceIoControl at all?: The driver is a HID minidriver, not a standard driver. Therefore, it is impossible to create a file handle with CreateFile, and of course it is impossible to use DeviceIoControl. In this case, how can...; lianxiangke Embedded System

Common ground problem of op amp: [i=s]This post was last edited by dontium on 2015-1-23 12:49[/i] Can anyone help me solve this problem? I want to amplify 0-10V to 0-15V. Why must the signal ground and power ground be connected toget...; lv499970142 Analogue and Mixed Signal

Doubts about compiling BSP: Adding a Driver to an Existing BSPTo add a device driver to an existing BSP definition using the BSP Wizard, you must already have created the device driver files, and they must reside in the BSP dire...; zhaojiang1 Embedded System

Have you seen the latest application of LED, “LED eyelashes”?: This is something that would be called non-mainstream, right? Is it a performance of "Ghost"? I guess it can be used to show its face at a masquerade. There is a clear line on the right eye, and the p...; banana Creative Market

Helper2416-31——Linux_Programing——Time Programming: [i=s] This post was last edited by yuanlai2010 on 2014-8-12 09:45[/i] [align=center][b][font=华文楷体][size=20.0pt]Time Programming[/size][/font][/b][/align][align=center][b][color=red][font=华文楷体][size=14...; yuanlai2010 Embedded System

[Decryption 11] Wireless remote control tank DIY based on 51 single chip microcomputer chassis structure and assembly: [align=left]I have shared with you the DIY process of making a remote control tank before, which introduced a lot of principles and some assembly processes. We have shared with you about 10 times befo...; @ZiShi DIY/Open Source Hardware

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components