ATT-561F-23-SC0-02 datasheet, PDF

Datasheet> All Categories > Wireless rf/communication> Radio frequency and microwave> ATT-561F-23-SC0-02

ATT-561F-23-SC0-02: DescriptionFixed Attenuator, 0MHz Min, 2000MHz Max; CategoryWireless rf/communication Radio frequency and microwave; File Size62KB，1 Pages; ManufacturerVertiv

Download Datasheet Parametric View All

ATT-561F-23-SC0-02 Overview

Fixed Attenuator, 0MHz Min, 2000MHz Max

ATT-561F-23-SC0-02 Parametric

Parameter Name	Attribute value
Reach Compliance Code	unknown
Other features	SC-F, I/P POWER-MAX(PEAK)=200W
Nominal attenuation	23 dB
Characteristic impedance	50 Ω
structure	COAXIAL
Maximum input power (CW)	33.01 dBm
Maximum operating frequency	2000 MHz
Minimum operating frequency
Maximum operating temperature	125 °C
Minimum operating temperature	-54 °C
RF/Microwave Device Types	FIXED ATTENUATOR
Maximum voltage standing wave ratio	1.25
Base Number Matches	1

Preview

Download Datasheet

View All

Attenuators

DC - 11GHz Performance

Frequency:

DC - 11.0 GHz and DC - 2.0 units available

Attenuation Values:

1 - 60 dB in 1 dB increments

Attenuation Accuracy:

1 - 6 dB + 0. 3 dB

7 - 20 dB

21 - 40 dB

41 - 60 dB

+ 0. 5 dB

+ 0.75 dB

+ 1.0 dB

SC Type

Impedance:

50 Ohms

VSWR:

1.25 max

Power:

2Watts average @ 25 C derated linearly to 0.5 Watts @ 125 C

Peak

Operating Temperature Range:

Finish:

Stainless Steel

DC - 11.0 GHz

Male / Female

ATT-0560-XX-SCO-02

10 Watts average @ 40C derated linearly to 0.5 watts @ 125 C

Power:

0.2 Kilowatts

-54C to +125C

560 Series

Female / Female

ATT-560F-XX-SCO-02

Model Number

Male / Male

ATT-560M-XX-SCO-02

Attenuation Value = XX, Select 1 - 60 dB in 1 dB increments

DC - 2.0 GHz

Male/Female

ATT-0561-SCO-02

561Series

Female/Female

ATT-561F-XX-SCO-02

Model Number

Male/Male

ATT-561M-XX-SCO-02

Attenuation Value = XX, Select 1 - 60 dB in 1 dB increments

DC - 11.0 GHz

Male/Female

562 Series

Female/Female

Model Number

Male/Male

ATT-562M-XX-SCO-07

ATT-0562-XX-SCO-07 ATT-562F-XX-SCO-07

Attenuation Value = XX, Select 1 - 60 dB in 1 dB increments

10 Watts

DC - 2.0 GHz

Male/Female

ATT-0563-XX-SCO-07

563 Series

Female/Female

ATT-563F-XX-SCO-07

Model Number

Male/Male

ATT-563M-XX-SCO-07

Attenuation Value = XX, Select 1 - 60 dB in 1 dB increments

10 Watts - 5 Kilowatts Peak

Recommended Resources

Controllable pulse signal generating circuit

Delay circuit two using 555 time base integrated circuit

Diamond differential input power amplifier circuit

Realize long-distance dual power supply mutual pin and mutual input circuit without interlocking control lines

One-way full voltage start control circuit

Automatic AC voltage regulator circuit

WinCE5.0 supports and uses CF cards, MMC cards, and SD cards as large as 64G.: I would like to ask all my colleagues in WinCE development: Is there any successful application that supports WinCE5.0 and uses CF cards, MMC or SD cards as large as 64G?...; jjnature Embedded System

6701 Compilation Problem: I wrote 6701 today, and the CMD file is as follows: -c -heap 0x1000 -stack 0x1000 MEMORY { VECS: o = 00000000h l = 00000200h BOOTRAM: o = 00000200h l = 00000200h PMEM: o = 00010000h l = 0000FC00h DMEM...; coldsun1982 DSP and ARM Processors

Universal serial port VHDL source program design: Part 1: Serial port receiving program LIBRARY IEEE;USE IEEE.STD_LOGIC_1164.ALL;USE IEEE.STD_LOGIC_ARITH.ALL;USE IEEE.STD_LOGIC_UNSIGNED.ALL; --LIBRARY ALTERA;--USE ALTERA.MAXPLUS2.ALL; LIBRARY LPM;USE...; eeleader FPGA/CPLD

I will be interviewing at Baidu next week. Please give me some advice, education, corrections, help and concern.: [i=s] This post was last edited by astwyg on 2014-5-22 21:29 [/i] I was helping a classmate pass on the news and applied for an internship in Baidu's quality department. Unexpectedly, I received a cal...; astwyg Talking

Help: FPGA and DSP communication problem: FPGA uses DSP's xintf interface to communicate with DSP. I have read a lot of information, but I am still confused. How can I make the timing of FPGA consistent with DSP? I have seen people say that d...; djky183 FPGA/CPLD

Show the WEBENCH design process + low-pass filter design solution: Previously, I knew that WEBENCH design was for power supply design. Now I see that its functions are much more powerful. Now I will use this tool to design a low-pass filter circuit. The circuit diagr...; hanskying666 Analogue and Mixed Signal

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components