E & E Magnetic Products Limited
LOW COST THT
POWER INDUCTORS
Toroid Type - Low Profile
Available in low profile
Characterized for general purpose use and ripple filters
Can be used as differential mode inductors in EMI filters
Can be used as SMPS averaging filter
Single-layer design
Operating temperature -40°C to +130°C
RoHS compliant
E
LECTRICAL
S
PECIFICATION @
25°C
Reference Operating Values
Part
Number
Inductance
Typical
(mH)
50
100
70
145
100
100
35.6
55
1
Design Control Values
2
I
DC
(A)
2.6
2.6
3.0
3.0
3.6
5.0
5.0
7.0
ET
OP
(V-mSec)
50
90
85
140
130
200
100
150
Energy
Storage
(mJ)
169
338
315
653
648
1250
445
1348
Inductance Inductance
5
No DC (mH) Test Volt.
DCR
±20%
(mV)
(mW Max)
45.7
94.1
61.0
141.8
90.7
90.7
55.6
49.1
45
90
73
140
110
180
88
100
71
110
52
95.7
49.5
34
23
17
3
4
Coil
Size
Code
1
2
2
3
3
4
3
4
Lead
Diameter
(Inch)
±.003
.020
.020
.025
.025
.032
.042
.042
.051
831-00186F
831-00187F
831-00188F
831-00189F
831-00190F
831-00191F
831-00192F
831-00193F
Notes:
1. Typical inductance occurs at I
DC
and ET
OP
values shown.
2. LI
2
/2 rating is the ability of the inductor to store energy.
3. Inductance is tested at 20kHz.
4. Design control test voltage is critical, inductance increases with voltage.
5. Add 10% more for low profile part.
6. The part temperature (ambient temperature + temperature rise) should not exceed the upper limit of the operating
temperature under worst case operating conditions. Circuit design, component placement, PWB trace size and
thickness, airflow and other cooling provisions all affect the part temperature. Part temperature should be verified
in the end application.
1/F., Harbour View 1, No.12 Science Park East Avenue, Phase II, Hong Kong Science Park, Shatin, N.T. Hong Kong
Tel: (852) 2954 3333
Fax: (852) 2954 3304
1
PI008(06)
Revised in
10/12
E & E Magnetic Products Limited
LOW COST THT
POWER INDUCTORS
Toroid Type - Low Profile
S
CHEMATICS
M
ECHANICAL
D
IMENSIONS
A
Size
Code
1
2
3
4
A
(Max)
.700
17.78
.850
21.59
1.050
26.67
1.400
35.56
B
(Max)
.380
9.65
.410
10.41
.550
13.97
.700
17.78
C
.530±.050
13.46±1.27
.720±.050
18.29±1.27
.840±.020
21.34±0.51
1.100±.100
27.94±2.54
.375
±
.125
9.53±3.18
REFERENCE OR
GAUGE PLANE
C
B
Notes:
7. All dimensions are specified in inches with higher precedence in inches.
mm
8. U
nless otherwise specified, all tolerances are
±
.010
.
0.25
S
CHEMATICS
1
2
FOR MORE INFORMATION, PLEASE CONTACT
HEADQUARTER
1/F., Harbour View 1, No.12 Science Park East Avenue,
Phase II, Hong Kong Science Park, Shatin, N.T.
Hong Kong
Tel: (852) 2954 3333 Fax: (852) 2954 3304
Email: eempl@eleceltek.com
Website: http://www.eleceltek.com / www.eemagnetic.com
Information herein is for reference only and subject to change without notice. It does not constitute any representation, warranty or commitment of the company in respect
of the products in any aspect. All logos, brands and product names mentioned herein are trademarks or registered trademarks of their respective owners. The company
does not assume any liability arising out of the application or use of any product or circuit described herein. Copyrights 2009, E & E Magnetic Products Limited.
1/F., Harbour View 1, No.12 Science Park East Avenue, Phase II, Hong Kong Science Park, Shatin, N.T. Hong Kong
Tel: (852) 2954 3333
Fax: (852) 2954 3304
2
PI008(06)
Revised in
10/12