AT29C040A_08 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> AT29C040A_08

AT29C040A_08: Description512K X 8 FLASH 5V PROM, 90 ns, PDSO32; Categorystorage; File Size376KB，17 Pages; ManufacturerAtmel (Microchip)

Download Datasheet Parametric Compare View All

AT29C040A_08 Overview

512K X 8 FLASH 5V PROM, 90 ns, PDSO32

AT29C040A_08 Parametric

Parameter Name	Attribute value
Number of functions	1
Number of terminals	32
Maximum operating temperature	85 Cel
Minimum operating temperature	-40 Cel
Maximum supply/operating voltage	5.5 V
Minimum supply/operating voltage	4.5 V
Rated supply voltage	5 V
maximum access time	90 ns
Processing package description	8 × 20 MM, LEAD AND HALIDE FREE, PLASTIC, MO-142BD, TSOP1-32
Lead-free	Yes
EU RoHS regulations	Yes
state	DISCONTINUED
Craftsmanship	CMOS
packaging shape	Rectangle
Package Size	SMALL OUTLINE, THIN PROFILE
surface mount	Yes
Terminal form	GULL WING
Terminal spacing	0.5000 mm
terminal coating	MATTE Tin
Terminal location	pair
Packaging Materials	Plastic/Epoxy
Temperature level	INDUSTRIAL
memory width	8
organize	512K × 8
storage density	4.19E6 deg
operating mode	ASYNCHRONOUS
Number of digits	524288 words
Number of digits	512K
Memory IC type	FLASH 5V programmable read-only memory
serial parallel	parallel
Maximum TWC of write cycle	10 ms

Preview

Download Datasheet

View All

Features

•

Fast Read Access Time – 90 ns

•

5-volt Only Reprogramming

•

Sector Program Operation

– Single Cycle Reprogram (Erase and Program)

– 2048 Sectors (256 Bytes/Sector)

– Internal Address and Data Latches for 256 Bytes

Internal Program Control and Timer

Hardware and Software Data Protection

Two 16K Bytes Boot Blocks with Lockout

Fast Sector Program Cycle Time – 10 ms

DATA Polling for End of Program Detection

Low Power Dissipation

– 40 mA Active Current

– 100 µA CMOS Standby Current

Typical Endurance > 10,000 Cycles

Single 5V

10% Supply

Green (Pb/Halide-free) Packaging Option

•

4-megabit

(512K x 8)

5-volt Only

256-byte Sector

Flash Memory

AT29C040A

1. Description

The AT29C040A is a 5-volt only in-system Flash Programmable and Erasable Read

Only Memory (PEROM). Its 4 megabits of memory is organized as 524,288 words by

8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS EEPROM technology,

the device offers access times up to 90 ns, and a low 220 mW power dissipation.

When the device is deselected, the CMOS standby current is less than 100 µA. The

device endurance is such that any sector can typically be written to in excess of

10,000 times. The programming algorithm is compatible with other devices in Atmel’s

5-volt only Flash family.

To allow for simple in-system reprogrammability, the AT29C040A does not require

high input voltages for programming. Five-volt-only commands determine the opera-

tion of the device. Reading data out of the device is similar to reading from an

EPROM. Reprogramming the AT29C040A is performed on a sector basis; 256 bytes

of data are loaded into the device and then simultaneously programmed.

During a reprogram cycle, the address locations and 256 bytes of data are internally

latched, freeing the address and data bus for other operations. Following the initiation

of a program cycle, the device will automatically erase the sector and then program

the latched data using an internal control timer. The end of a program cycle can be

detected by DATA polling of I/O7. Once the end of a program cycle has been

detected, a new access for a read or program can begin.

0333L–FLASH–9/08

AT29C040A

3. Block Diagram

4. Device Operation

4.1

Read

The AT29C040A is accessed like an EPROM. When CE and OE are low and WE is high, the

data stored at the memory location determined by the address pins is asserted on the outputs.

The outputs are put in the high impedance state whenever CE or OE is high. This dual-line con-

trol gives designers flexibility in preventing bus contention.

4.2

Byte Load

Byte loads are used to enter the 256 bytes of a sector to be programmed or the software codes

for data protection. A byte load is performed by applying a low pulse on the WE or CE input with

CE or WE low (respectively) and OE high. The address is latched on the falling edge of CE or

WE, whichever occurs last. The data is latched by the first rising edge of CE or WE.

4.3

Program

The device is reprogrammed on a sector basis. If a byte of data within a sector is to be changed,

data for the entire sector must be loaded into the device. Any byte that is not loaded during the

programming of its sector will be erased to read FFH. Once the bytes of a sector are loaded into

the device, they are simultaneously programmed during the internal programming period. After

the first data byte has been loaded into the device, successive bytes are entered in the same

manner. Each new byte to be programmed must have its high to low transition on WE (or CE)

within 150

μs

of the low to high transition of WE (or CE) of the preceding byte. If a high to low

transition is not detected within 150

μs

of the last low to high transition, the load period will end

and the internal programming period will start. A8 to A18 specify the sector address. The sector

address must be valid during each high to low transition of WE (or CE). A0 to A7 specify the byte

address within the sector. The bytes may be loaded in any order; sequential loading is not

required. Once a programming operation has been initiated, and for the duration of t

, a read

operation will effectively be a polling operation.

4.4

Software Data Protection

A software controlled data protection feature is available on the AT29C040A. Once the software

protection is enabled a software algorithm must be issued to the device before a program may

0333L–FLASH–9/08

be performed. The software protection feature may be enabled or disabled by the user; when

shipped from Atmel, the software data protection feature is disabled. To enable the software

data protection, a series of three program commands to specific addresses with specific data

must be performed. After the software data protection is enabled the same three program com-

mands must begin each program cycle in order for the programs to occur. All software program

commands must obey the sector program timing specifications. The SDP feature protects all

sectors, not just a single sector. Once set, the software data protection feature remains active

unless its disable command is issued. Power transitions will not reset the software data protec-

tion feature, however the software feature will guard against inadvertent program cycles during

power transitions.

After setting SDP, any attempt to write to the device without the three-byte command sequence

will start the internal write timers. No data will be written to the device; however, for the duration

of t

, a read operation will effectively be a polling operation.

After the software data protection’s 3-byte command code is given, a byte load is performed by

applying a low pulse on the WE or CE input with CE or WE low (respectively) and OE high. The

address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by

the first rising edge of CE or WE. The 256 bytes of data must be loaded into each sector by the

same procedure as outlined in the program section under device operation.

4.5

Hardware Data Protection

Hardware features protect against inadvertent programs to the AT29C040A in the following

ways: (a) V

sense – if V

is below 3.8V (typical), the program function is inhibited; (b) V

power on delay – once V

has reached the V

sense level, the device will automatically time

out 5 ms (typical) before programming; (c) Program inhibit – holding any one of OE low, CE high

or WE high inhibits program cycles; and (d) Noise filter – pulses of less than 15 ns (typical) on

the WE or CE inputs will not initiate a program cycle.

4.6

Product Identification

The product identification mode identifies the device and manufacturer as Atmel. It may be

accessed by hardware or software operation. The hardware operation mode can be used by an

external programmer to identify the correct programming algorithm for the Atmel product. In

addition, users may wish to use the software product identification mode to identify the part

(i.e. using the device code), and have the system software use the appropriate sector size for

program operations. In this manner, the user can have a common board design for 256K to

4-megabit densities and, with each density’s sector size in a memory map, have the system soft-

ware apply the appropriate sector size.

For details, see Operating Modes (for hardware operation) or Software Product Identification.

The manufacturer and device code is the same for both modes.

4.7

DATA Polling

The AT29C040A features DATA polling to indicate the end of a program cycle. During a pro-

gram cycle an attempted read of the last byte loaded will result in the complement of the loaded

data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and

the next cycle may begin. DATA polling may begin at any time during the program cycle.

4.8

Toggle Bit

In addition to DATA polling the AT29C040A provides another method for determining the end of

a program or erase cycle. During a program or erase operation, successive attempts to read

AT29C040A

0333L–FLASH–9/08

AT29C040A

data from the device will result in I/O6 toggling between one and zero. Once the program cycle

has completed, I/O6 will stop toggling and valid data will be read. Examining the toggle bit may

begin at any time during a program cycle.

4.9

Optional Chip Erase Mode

The entire device can be erased by using a 6-byte software code. Please see Software Chip

Erase application note for details.

4.10

Boot Block Programming Lockout

The AT29C040A has two designated memory blocks that have a programming lockout feature.

This feature prevents programming of data in the designated block once the feature has been

enabled. Each of these blocks consists of 16K bytes; the programming lockout feature can be

set independently for either block. While the lockout feature does not have to be activated, it can

be activated for either or both blocks.

These two 16K memory sections are referred to as

boot blocks.

Secure code which will bring up

a system can be contained in a boot block. The AT29C040A blocks are located in the first 16K

bytes of memory and the last 16K bytes of memory. The boot block programming lockout feature

can therefore support systems that boot from the lower addresses of memory or the higher

addresses. Once the programming lockout feature has been activated, the data in that block can

no longer be erased or programmed; data in other memory locations can still be changed

through the regular programming methods. To activate the lockout feature, a series of seven

program commands to specific addresses with specific data must be performed. Please see

Boot Block Lockout Feature Enable Algorithm.

If the boot block lockout feature has been activated on either block, the chip erase function will

be disabled.

4.10.1

Boot Block Lockout Detection

A software method is available to determine whether programming of either boot block section is

locked out. See Software Product Identification Entry and Exit sections. When the device is in

the software product identification mode, a read from location 00002H will show if programming

the lower address boot block is locked out while reading location 7FFF2H will do so for the upper

boot block. If the data is FE, the corresponding block can be programmed; if the data is FF, the

program lockout feature has been activated and the corresponding block cannot be pro-

grammed. The software product identification exit mode should be used to return to standard

operation.

5. Absolute Maximum Ratings*

Temperature Under Bias............................... -55° C to +125° C

Storage Temperature .................................... -65° C to +150° C

All Input Voltages (including NC Pins)

with Respect to Ground ...................................-0.6V to +6.25V

All Output Voltages

with Respect to Ground .............................-0.6V to V

+ 0.6V

Voltage on OE

with Respect to Ground ...................................-0.6V to +13.5V

*NOTICE:

Stresses beyond those listed under “Absolute

Maximum Ratings” may cause permanent dam-

age to the device. This is a stress rating only and

functional operation of the device at these or any

other conditions beyond those indicated in the

operational sections of this specification is not

implied. Exposure to absolute maximum rating

conditions for extended periods may affect

device reliability.

0333L–FLASH–9/08

AT29C040A_08 Related Products

	AT29C040A_08	AT29C040A-90TU	AT29C040A-90JU
Description	512K X 8 FLASH 5V PROM, 90 ns, PDSO32	512K X 8 FLASH 5V PROM, 90 ns, PDSO32	512K X 8 FLASH 5V PROM, 90 ns, PDSO32
Number of functions	1	1	1
Number of terminals	32	32	32
Maximum operating temperature	85 Cel	85 °C	85 °C
Minimum operating temperature	-40 Cel	-40 °C	-40 °C
surface mount	Yes	YES	YES
Terminal form	GULL WING	GULL WING	J BEND
Terminal location	pair	DUAL	QUAD
Temperature level	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL
memory width	8	8	8
organize	512K × 8	512KX8	512KX8
Is it Rohs certified?	-	conform to	conform to
Maker	-	Atmel (Microchip)	Atmel (Microchip)
Parts packaging code	-	TSOP1	QFJ
package instruction	-	8 X 20 MM, LEAD AND HALIDE FREE, PLASTIC, MO-142BD, TSOP1-32	LEAD AND HALIDE FREE, PLASTIC, MS-016AE, LCC-32
Contacts	-	32	32
Reach Compliance Code	-	unknow	unknow
ECCN code	-	EAR99	EAR99
Maximum access time	-	90 ns	90 ns
startup block	-	BOTTOM/TOP	BOTTOM/TOP
command user interface	-	NO	NO
Data polling	-	YES	YES
JESD-30 code	-	R-PDSO-G32	R-PQCC-J32
JESD-609 code	-	e3	e3
length	-	18.4 mm	13.97 mm
memory density	-	4194304 bi	4194304 bi
Memory IC Type	-	FLASH	FLASH
Humidity sensitivity level	-	3	2
Number of departments/size	-	2K	2K
word count	-	524288 words	524288 words
character code	-	512000	512000
Operating mode	-	ASYNCHRONOUS	ASYNCHRONOUS
Package body material	-	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	-	TSOP1	QCCJ
Encapsulate equivalent code	-	TSSOP32,.8,20	LDCC32,.5X.6
Package shape	-	RECTANGULAR	RECTANGULAR
Package form	-	SMALL OUTLINE, THIN PROFILE	CHIP CARRIER
page size	-	256 words	256 words
Parallel/Serial	-	PARALLEL	PARALLEL
Peak Reflow Temperature (Celsius)	-	260	245
power supply	-	5 V	5 V
Programming voltage	-	5 V	5 V
Certification status	-	Not Qualified	Not Qualified
Maximum seat height	-	1.2 mm	3.556 mm
Department size	-	256	256
Maximum standby current	-	0.0003 A	0.0003 A
Maximum slew rate	-	0.04 mA	0.04 mA
Maximum supply voltage (Vsup)	-	5.5 V	5.5 V
Minimum supply voltage (Vsup)	-	4.5 V	4.5 V
Nominal supply voltage (Vsup)	-	5 V	5 V
technology	-	CMOS	CMOS
Terminal surface	-	Matte Tin (Sn)	Matte Tin (Sn)
Terminal pitch	-	0.5 mm	1.27 mm
Maximum time at peak reflow temperature	-	30	40
switch bit	-	YES	YES
type	-	NOR TYPE	NOR TYPE
width	-	8 mm	11.43 mm
Maximum write cycle time (tWC)	-	10 ms	10 ms

Recommended Resources

High current voltage regulator circuit

Sensitive simple voltmeter circuit

Lighting lamp, infrared lamp, iodine tungsten lamp wiring method circuit

Electronic ballast circuit for fluorescent lamps with a lifespan of 20,000 hours

Rice cooker fire power controller circuit

Help: If anyone has the Chinese manual for CMU200 and CMD55, please share it with me. Thank you!...; fulihua Test/Measurement

MSP430G2 development board learning (ten): timer A overflow interrupt (32768KHZ clock): MSP430G2 development board learning (ten): Timer A overflow interrupt (32768KHZ clock) /**************************************************************************** * Timer A, flip P1.0LED, Timer A ov...; lilong8470 Microcontroller MCU

I have a question about whether a barometer can be used for weighing.: I want to ask whether a barometer can be used for weighing. I once wanted to have a balance. I went around the street and asked two people. It seemed that it was not cheap. If I asked too many questio...; wangfuchong Talking

Help with JTAG burning program: I just made a board, but the program won't burn into it. The circuit should be fine, because once by chancethe program burned into it, but it didn't work afterwards. Can you tell me what the reason mi...; xhs162861 Microcontroller MCU

Please help me, why can't the HEX digital tube and OUTS simulation be done? A novice needs help.: module dj (clk_27m,rst_n,fangxiang,sudu,outf,outs,count_gd,HEX1,HEX2,HEX3,HEX4);input clk_27m;input rst_n;input fangxiang;input sudu;input count_gd;output outf,outs;output [6:0]HEX1,HEX2,HEX3,HEX4;reg...; 关耳008 FPGA/CPLD

The problem of signal output affecting the circuit!: I encountered a strange problem. If I assign a signal in the circuit to an output pin, the logic of the entire circuit is wrong. (If it is not output, the logic is correct when observed through other ...; eeleader FPGA/CPLD

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components