REVISIONS
LTR
A
Add device type 02 (AD571).
Make corrections to terminal connections. Make corrections to digital input
high current and digital input low current test units. Make corrections to power
supply rejection test conditions. Make corrections to switching waveforms.
Add MIL-M-38510 information to 6.2 and 6.6. Make correction to three-state
leakage current test units. Editorial changes throughout.
Add device type 03. Editorial changes throughout.
Drawing updated to reflect current requirements. -rrp
Modify drawing to current requirements. -rrp
Under table I, full scale temperature drift test, for device type 02 only;
maximum limit column, delete
±0.488
and substitute
±0.781.
Under table I, I
CC
power supply current test, both conditions, for device types
01 and 02, delete 10 mA and substitute 15 mA. - ro
DESCRIPTION
DATE (YR-MO-DA)
87-12-01
APPROVED
R. P. Evans
B
90-06-04
M. A. Frye
C
D
E
97-02-10
03-02-07
10-10-20
R. Monnin
R. Monnin
C. Saffle
F
12-07-31
C. Saffle
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
REV
SHEET
PREPARED BY
Donald R. Osborne
F
1
F
2
F
3
F
4
F
5
F
6
F
7
F
8
F
9
F
10
F
11
F
12
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
D.A. Di Cenzo
APPROVED BY
Nelson Hauck
DRAWING APPROVAL DATE
87-04-17
REVISION LEVEL
F
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
MICROCIRCUIT, LINEAR, ANALOG-TO-DIGITAL
CONVERTERS WITH THREE-STATE BUFFERED
OUTPUTS, MONOLITHIC SILICON
SIZE
A
CAGE CODE
AMSC N/A
14933
SHEET
1 OF 12
5962-86802
DSCC FORM 2233
APR 97
5962-E193-12
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part
or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following examples.
For device classes M and Q:
5962
-
86802
01
V
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
Device
type
(see 1.2.2)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
\/
Drawing number
For device class V:
5962
-
86802
01
V
V
A
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
/
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
03
Generic number
AD570
AD571
AD571
Circuit function
8-bit A/D with three-state output
10-bit A/D with three-state output
10-bit A/D with three-state output
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed
below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q
designators will not be included in the PIN and will not be marked on the device.
Device class
M
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-
JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
Q or V
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86802
SHEET
F
2
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
V
Descriptive designator
GDIP1-T18 or CDIP2-T18
Terminals
18
Package style
Dual-in-line
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 1/
Negative supply voltage (V
EE
) to digital common ...................................................... -16.5 V dc
Positive supply voltage (V
CC
) to digital common ....................................................... +7 V dc
Analog input voltage to analog common ....................................................................
±15
V dc
Digital input voltage to digital common ...................................................................... 0 V dc to V
CC
Digital output voltage to digital common .................................................................... 0 V dc to V
CC
Analog return to digital common ................................................................................
±1
V dc
Power dissipation (T
A
= 25°C) ................................................................................... 800 mW
Lead temperature (soldering, 10 seconds) ................................................................ +300°C
Storage temperature range ........................................................................................ -65°C to +150°C
Junction temperature (T
J
) .......................................................................................... +175°C
Thermal resistance, junction-to-case (θ
JC
) ................................................................ See MIL-STD-1835
Thermal resistance, junction-to-ambient (θ
JA
) ........................................................... +88°C/W
1.4 Recommended operating conditions.
Positive supply voltage range ....................................................................................
Negative supply voltage range ..................................................................................
Minimum high-level input voltage ..............................................................................
Maximum low-level input voltage ...............................................................................
Ambient operating temperature range (T
A
) ...............................................................
+4.5 V dc to +5.5 V dc
-13.5 V dc to -16.0 V dc
+2.0 V dc
+0.8 V dc
-55°C to +125°C
_____
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86802
SHEET
F
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 -
MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 -
MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.dla.mil/quicksearch/
or from the Standardization Document
Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86802
SHEET
F
4
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of
MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime 's agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 57 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-86802
SHEET
F
5
京公网安备 11010802033920号
EEWORLD
