Embedded Power for
Business-Critical Continuity
NTS500 Series
500 Watts
Total Power:
Input Voltage:
# of Outputs:
200 - 500 Watts
85 - 264 Vac
120 - 300 Vdc
Single
Rev. 05.27.08
NTS500 Series
1 of 3
RoHS
Electrical Specifications
Special Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Active power factor correction
IEC EN61000-3-2 compliance
Remote sense
Power fail and remote inhibit
Single wire current sharing
Built-in EMI filter
Low output ripple
5V standby
12V fan output
Overvoltage protection
Overload protection
Thermal overload protection
DC power good
Built in OR-ing diode / FET
Optional fan cover (-CF suffix)
PM Bus compliant
Digital I
2
C interface
2 year warranty
POE isolation on NTS508
Input
Input range:
Frequency:
Inrush current:
Efficiency:
EMI filter:
85 - 264 Vac (wide range)
47-63 Hz
50 A max., cold start @ 25°C
85% typical at full load, nominal line
FCC Class B conducted and radiated; CISPR22 Class B
conducted and radiated; EN55022 Class B conducted and
radiated; VDE0878PT3 Class B conducted and radiated.
<0.5 mA @ 50/60 Hz, 264 Vac input
Safety ground leakage
current:
Output
Maximum power:
Adjustment range:
Standby output:
Fan output:
Hold-up time:
Overload protection:
200 W for convection; 500 W with 30 CFM forced air
±5%
5 V @ 1 A regulated, ±5%
12 V @ 0.5 A, -5 %, +7%, 0.5 A for -CF version
20 ms @ 500 W load, 115 VAC nominal line at factory voltage
setting
Short circuit protection on all outputs. Case overload
protected @ 115-130% above peak rating
Overvoltage protection: 20-35% above nominal output
Safety
TUV:
cCSAus:
NEMKO:
AUSTEL:
CB:
CE:
60950
60601-1
60950
60950
Certificate and report
Mark (LVD)
Embedded Power for
Business-Critical Continuity
Logic Control
Power failure:
Remote on/off:
DC OK:
Remote sense:
TTL logic signal goes high 100-500 msec after main output.
It goes low at least 4 msec before loss of regulation
Requires an external contact closure to inhibit outputs
TTL logic goes high after the output is in regulation. It goes
low when there is loss of regulation.
Compensates for 0.5 V lead drop min. Will operate without
remote sense connected. Reverse connection protected.
Rev. 05.27.08
NTS500 Series
2 of 3
Pin Assignments
Connector
CN1
PIN 1
PIN 3
PIN 5
SK7
PIN 1
PIN 2
PIN 3
PIN 4
PIN 5
PIN 6
PIN 7
PIN 8
PIN 9
PIN 10
PIN 1
PIN 2
PIN 3
PIN 4
PIN 6
PIN 7
PIN 8
PIN 9
PIN 10
Line
Neutral
Ground
V1 swp
- Remote Sense
+ Remote Sense
5 VSB (standby)
5 VSB return
+12 V
Common
Inhibit
DC power good (DC OK)
Power Fail (POK)
Ground
A2_out
A1_out
A0_out
I
2
C_sda_out
5 V_I
2
C
n/c
n/c
n/c
Environmental Specifications
Operating temperature:
Storage temperature:
Electromagnetic
susceptibility:
Humidity:
Vibration:
0° to 50 °C ambient derate each output as 2.5% per degree
from 50° to 70 °C.
-40°C to +85°C
Designed to meet EN61000-4;
-2, -3, -4, -5, -6, -8, -11 Level 3
Operating; non-condensing 10% to 90% RH
Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances
2 G peak 8 Hz to 500 Hz, operational
1M hours at full load and 25 °C ambient conditions
1
5
6
10
CN403
1
6
10
5
MTBF demonstrated:
Adjustment Potentiometers
P1
+V1 Output adjust
P3
+5 VSB adjust
Mating Connectors
SK4,5,6
Molex 19141-0058
Ordering Information
Model
Number
NTS503
NTS505
NTS508
Output
Voltage
12 V
24 V
48 V
Maximum Load Maximum Load
Minimum
with Convection with 30CFM Peak Load
1
Regulation
2
Load
Cooling
Forced Air
0A
0A
0A
16.6 A
8.3 A
4.2 A
41.7 A
20.8 A
10.4 A
47 A
23.4 A
11.7 A
±2%
±2%
±2%
Ripple
P/P (PARD)
3
120 mV
240 mV
480 mV
SK7 Control
Molex 90142-0010
signals
PINS: 90119-2110
or
Amp: 87977-3
PINS: 87309-8
SK8
CN403
Molex 22-01-2025
Pins: 08-52-0123
JST PHDR-10VS
Pins: JST 5PHD-002T-PO.5-L/P or
Landwin 2050 S1000
Pins: 2053T011P
1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 μF (tantalum capacitor) in parallel with a 0.1 μF capacitor at
rated line voltage and load ranges.
4. 5 V standby and 12 V fan output cannot be used above 50 °C with convection cooling.
Astec Connector Kit #70-841-024 includes all
of the above
Notes:
1. Specifications subject to change without
notice.
2. All dimensions in inches (mm), tolerance
is ±.02".
3. Specifications are at factory settings
4. Mounting maximum insertion depth is
0.12".
5. Warranty: 2 year
6. Weight: 3.016 lb. / 1.18 kg.
Embedded Power for
Business-Critical Continuity
Mechanical Drawing
Americas
5810 Van Allen Way
Carlsbad, CA 92008
USA
Telephone: +1 (760) 930 4600
Facsimile: +1 (760) 930 0698
Rev. 05.27.08
NTS500 Series
3 of 3
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
Telephone: +44 (0) 1384 842 211
Facsimile: +44 (0) 1384 843 355
CN1
SK7
V out adj.
(CN403)
Asia (HK)
SK8
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
Telephone: +852 2176 3333
Facsimile: +852 2176 3888
For global contact, visit:
www.powerconversion.com
techsupport.embeddedpower
@emerson.com
While every precaution has been taken to ensure
accuracy and completeness in this literature, Emerson
Network Power assumes no responsibility, and disclaims
all liability for damages resulting from use of this
information or for any errors or omissions.
Emerson Network Power.
The global leader in enabling
business-critical continuity.
AC Power
Connectivity
DC Power
Embedded Computing
Embedded Power
Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
Racks & Integrated Cabinets
Services
Surge Protection
EmersonNetworkPower. com
Emerson Network Power and the Emerson
Network Power logo are trademarks and
service marks of Emerson Electric Co.
©2008 Emerson Electric Co.
京公网安备 11010802033920号
EEWORLD
