adjustable reference in a 6-pin SOT-23 package that is
optimized for lithium-ion low battery detection circuits.
The LTC1998 features a voltage detection circuit with an
adjustable threshold voltage and hysteresis. The threshold
voltage can be programmed from 2.5V to 3.25V with two
external resistors. A 10mV to 750mV hysteresis can be
added with a third external resistor.
A proprietary internal architecture maintains 1% thresh-
old voltage accuracy over temperature with low cost 1%
external resistors.
A separate power supply pin, V
LOGIC,
allows the battery-low
logic output to operate below the battery voltage, allowing
compatibility with low voltage microprocessors without a
pull-up resistor. Power supply glitches are eliminated by
preventing the cross-conducting current which occurs
when the output changes state.
The LTC1998 operates with battery or supply voltages
up to 5.5V and its battery-low output is valid for battery
voltages above 1.5V.
High Accuracy Trip Voltage: 1% Max Error Using
External 1% Resistors
Adjustable Threshold Voltage and Hysteresis
Quiescent Current: 2.5μA Typ
Output Swings Rail-to-Rail
Thresholds Programmable from 2.5V to 3.25V
Output State Guaranteed for V
BATT
≥1.5V
Low Profile (1mm) ThinSOT™ Package
APPLICATIONS
n
Lithium-Ion Battery-Powered Equipment
PDAs
Cell Phones
Handheld Instruments
Battery Packs
Pagers
Palm Top Computers
POS Terminals
L,
LT, LTC and LTM are registered trademarks of Linear Technology Corporation. ThinSOT is
a trademark of Linear Technology Corporation. All other trademarks are the property of their
respective owners.
BLOCK DIAGRAM
Threshold Voltage Error vs Temperature
BATT
V
LOGIC
1.1R
V
HYST.A
V
TH.A
1.2V
% ERROR
THRESHOLD
ADJUST
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
1998 BD
V
TH.A
SET BY 1%
EXTERNAL R,
THRESHOLD = 3V
R
BATTLO
V
TH.A
= 1V
THRESHOLD = 3V
V
TH.A
SHORTED
TO GROUND,
THRESHOLD = 2.5V
0
–45 –25
35
15
55
–5
TEMPERATURE (°C)
75
95
1998 TA02
1998fa
1
LTC1998
ABSOLUTE MAXIMUM RATINGS
(Note 1)
PIN CONFIGURATION
TOP VIEW
BATT 1
GND 2
V
TH.A
3
6
BATTLO
5 V
LOGIC
4 V
H.A
Total Supply Voltage (BATT or V
LOGIC
to GND)............6V
Voltage
V
TH.A
, V
H.A
....................... BATT + 0.3V to GND – 0.3V
BATTLO
..........................V
LOGIC
+ 0.3V to GND – 0.3V
Operating Temperature Range (Note 3).... –40°C to 85°C
Specified Temperature Range (Note 4)
LTC1998C ............................................ –40°C to 85°C
LTC1998I.............................................. –40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) .................. 300°C
S6 PACKAGE
6-LEAD PLASTIC SOT-23
T
JMAX
= 150°C,
θ
JA
= 250°C/W
ORDER INFORMATION
LEAD FREE FINISH
LTC1998CS6#PBF
LTC1998IS6#PBF
LEAD BASED FINISH
LTC1998CS6
LTC1998IS6
TAPE AND REEL
LTC1998CS6#TRPBF
LTC1998IS6#TRPBF
TAPE AND REEL
LTC1998CS6#TR
LTC1998IS6#TR
PART MARKING
LTTY
LTTY
PART MARKING
LTTY
LTTY
PACKAGE DESCRIPTION
6-Lead Plastic SOT-23
6-Lead Plastic SOT-23
PACKAGE DESCRIPTION
6-Lead Plastic SOT-23
6-Lead Plastic SOT-23
TEMPERATURE RANGE
–40°C to 85°C
–40°C to 85°C
TEMPERATURE RANGE
–40°C to 85°C
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
1998fa
2
LTC1998
ELECTRICAL CHARACTERISTICS
PARAMETER
Power Supply
Supply Voltage Range-BATT
Supply Voltage Range-V
LOGIC
Supply Current, V
BATT
= 3V,
V
TH.A
= 1.5V
Supply Current, V
BATT
= 5.5V,
V
TH.A
= 1.5V
Monitor
Threshold Accuracy
V
BATT.Th
= 2.5V, Pin 3 Shorted to Ground
V
BATT.Th
= 3V, Pin 3 Driven by Precision Voltage Source to 1V
LTC1998C
LTC1998I
V
BATT.Th
= 3V, V
TH.A
= 1V (Note 5)
Programmed with 1% Max External Resistors
LTC1998C
LTC1998I
V
BATT.Th
= 3.25V, Pin 3 Driven by Precision Voltage Source to 1.5V
LTC1998C
LTC1998I
V
BATT.Th
= 3.25V, V
TH.A
= 1.5V (Note 5)
Programmed with 1% Max External Resistors
LTC1998C
LTC1998I
Hysteresis Accuracy
Allowable Hysteresis Range (Note 2)
Propagation Delay
C
OUT
= 100pF
Overdrive = 10mV
Overdrive = 100mV
V
TH.A
≤ 1.5V
V
H.A
≤ 1.5V
I
OUT
= –1mA, V
LOGIC
≥ 1.5V
I
OUT
= 1mA, V
BATT
≥ 2V
I
OUT
= 0.25mA, V
BATT
= 1V
l
l
l
l
l
l
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
GND
= 0V, unless otherwise noted.
CONDITIONS
MIN
1.5
1
2.5
TYP
MAX
5.5
V
BATT
3.5
4.2
4.5
4.3
5.2
5.5
0.85
1
0.61
0.71
UNITS
V
V
μA
μA
μA
μA
μA
μA
%
%
%
%
T
A
= 25°C
LTC1998CS6
LTC1998IS6
T
A
= 25°C
LTC1998CS6
LTC1998IS6
l
l
l
l
3
0.6
0.8
0.5
0.6
l
l
l
l
0.8
0.9
0.6
0.7
1
1.1
0.65
0.85
%
%
%
%
l
l
l
l
l
0.9
1
–5
±5
10
350
150
0.01
0.01
V
LOGIC
– 0.3
1.1
1.3
5
750
%
%
mV
mV
mV
μs
μs
V
HYST
≤ 250mV
250mV ≤ V
HYST
≤ 750mV
Threshold Adjust Pin Leakage, I
TH.A
Hysteresis Adjust Pin Leakage, I
H.A
Output
BATTLO
High Voltage
BATTLO
Low Voltage
BATTLO
Low Voltage
1
1
nA
nA
V
0.2
0.3
V
V
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Maximum allowable hysteresis depends on desired trip voltages.
See application notes for details.
Note 3:
LTC1998C and LTC1998I are guaranteed functional over the
operating temperature range of –40°C to 85°C.
Note 4:
The LTC1998C is guaranteed to meet specified performance from
0°C to 70°C. The LTC1998C is designed, characterized and expected to
meet specified performance from –40°C to 85°C but is not tested or QA
sampled at these temperatures. The LTC1998I is guaranteed to meet
I have always wanted to have my own single-chip microcomputer development board, but I don't have the money to make a board, so I can only solder one with a universal board. It doesn't feel difficult ...
I'm working on system model identification recently. However, the input of the test instrument is analog, while the encoder is a digital encoder, and the output is a pulse with varying frequency. I wo...
I am writing a PCI driver, the chip used is PCI9052, and each function of the whole code has output information. I am driving the flow light experiment program of the development board, mainly in the ...
[align=left][color=rgb(0, 0, 0)][backcolor=rgb(237, 235, 235)][url=https://download.eeworld.com.cn/detail/froglucky/539179]Use PT4107 to make a BUCK circuit LED driver circuit[/url][/backcolor][/color...
I am using EK-LM3S811 as my learning board and IAR FOR ARM 6.30 as my development environment. I cannot download the program when I am simulating the hardware. I used LM flash programmer to erase all ...
A ventilator is an instrument that can replace or assist a person's respiratory function. It is suitable for artificial respiration of patients with respiratory failure or even respiratory arrest. I...[Details]
Medical and industrial applications often require isolation voltages of 2500Vac or higher for patient and equipment operator safety. The isolation barrier must not only transmit power to the sensin...[Details]
Implantable Cardivoerter Defibrillators (ICDs) have been in common use for several years. ICDs apply a high voltage pulse between two electrodes connected to the heart, which detects cardiac fibrillat...[Details]
As a branch of signal and information processing, digital signal processing has penetrated into various fields of scientific research, technological development, industrial production, national defens...[Details]
As microcontrollers become less expensive and more powerful, electrical designers are finding it more cost-effective to use multiple small controllers in both single-board and multi-board systems. ...[Details]
0 Introduction
Today, with the rapid development of electronic technology and the emergence of new multifunctional electric energy meters, the choice of memory in the electric energy m...[Details]
DC regulated power supply is a commonly used electronic device, which can ensure stable output voltage when the grid voltage fluctuates or the load changes. A low ripple, high-precision regulated p...[Details]
When using GPS for positioning, it will be affected by various factors. The factors that affect the accuracy of GPS positioning can be divided into the following four categories (see the figure be...[Details]
Among the many candidate standards for China's mobile TV, the CMMB standard proposed by the Broadcasting Science Research Institute of the State Administration of Radio, Film and Television is aime...[Details]
Fetal monitoring is an important means to ensure the safety of perinatal mothers and fetuses and achieve eugenics. Intelligent fetal monitoring is a monitoring method that analyzes the health stat...[Details]
Multiple Input and Multiple Output (MIMO) technology is arguably the next most important development in wireless communication technology since the advent of digital communications. Many new wir...[Details]
l Introduction
Traditional human-computer communication is achieved through keyboard or mouse. The speed of information exchange is relatively slow, and the operator is required to have certain...[Details]
AD8205 is a single-power high-performance differential amplifier launched by Analog Devices, Inc., USA. The typical single-power supply voltage is 5V, and its common-mode voltage input r...[Details]
CVC5.0 (CSR recently announced the fifth generation of clear voice capture technology) is the only solution on the market that provides advanced audio enhancement and noise suppression to both the ...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
