HCPL-M600, HCPL-M601, HCPL-M611
Small Outline, 5 Lead, High CMR,
High Speed, Logic Gate Optocouplers
Data Sheet
Description
These small outline high CMR, high speed, logic gate
optocouplers are single channel devices in a five lead
miniature footprint. They are electrically equivalent to
the following Avago optocouplers (except there is no
output enable feature):
SO-5 Package
HCPL-M600
HCPL-M601
HCPL-M611
Standard DIP
6N137
HCPL-2601
HCPL-2611
SO-8 Package
HCPL-0600
HCPL-0601
HCPL-0611
Features
•
Surface Mountable
•
Very Small, Low Profile JEDEC Registered Package
Outline
•
Compatible with Infrared Vapor Phase Reflow and
Wave Soldering Processes
•
Internal Shield for High Common Mode Rejection
(CMR)
HCPL-M601: 10,000 V/µs at V
CM
= 50 V
HCPL-M611: 15,000 V/µs at V
CM
= 1000 V
•
High Speed: 10 Mbd
•
LSTTL/TTL Compatible
•
Low Input Current Capability: 5 mA
•
Guaranteed ac and dc Performance over Tempera-
ture: –40°C to 85°C
•
Recognized under the Component Program of U.L.
(File No. E55361) for Dielectric Withstand Proof Test
Voltage of 3750 Vac, 1 Minute
•
Lead Free Option
The SO-5 JEDEC registered (MO-155) package outline
does not require “through holes” in a PCB. This package
occupies approximately one fourth the footprint area
of the standard dual-in-line package. The lead profile is
designed to be compatible with standard surface mount
processes.
The HCPL-M600/01/11 optically coupled gates combine
a GaAsP light emitting diode and an integrated high gain
photon detector. The output of the detector I.C. is an Open-
collector Schottky-clamped transistor. The internal shield
provides a guaranteed common mode transient immunity
specification of 5,000 V/µs for the HCPL-M601, and 10,000
V/µs for the HCPL-M611.
This unique design provides maximum ac and dc circuit
isolation while achieving TTL compatibility. The optocou-
pler ac and dc operational parameters are guaranteed from
–40°C to 85°C allowing trouble free system perfor-
mance.
Applications
•
•
•
•
•
•
•
•
•
Isolated Line Receiver
Simplex/Multiplex Data Transmission
Computer-Peripheral Interface
Microprocessor System Interface
Digital Isolation for A/D, D/A Conversion
Switching Power Supply
Instrument Input/Output Isolation
Ground Loop Elimination
Pulse Transformer Replacement
CAUTION: The small device geometries inherent to the design of this bipolar component increase the component's
susceptibility to damage from electrostatic discharge (ESD). It is advised that normal static precautions be taken in
handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.
The SO-5 JEDEC registered (MO-155) package outline
does not require “through holes” in a PCB. This package
occupies approximately one fourth the footprint area
of the standard dual-in-line package. The lead profile is
designed to be compatible with standard surface mount
processes.
The HCPL-M600/01/11 optically coupled gates combine
a GaAsP light emitting diode and an integrated high gain
photon detector. The output of the detector I.C. is an
Open-collector Schottky-clamped transistor. The internal
shield provides a guaranteed common mode transient
immunity specification of 5,000 V/µs for the HCPL-M601,
and 10,000 V/µs for the HCPL-M611.
This unique design provides maximum ac and dc circuit iso-
lation while achieving TTL compatibility. The optocoupler
ac and dc operational parameters are guaranteed from -
40°C to 85°C allowing trouble free system performance.
The HCPL-M600/01/11 are suitable for high speed logic
interfacing, input/output buffering, as line receivers in
environments that conventional line receivers cannot
tolerate, and are recommended for use in extremely high
ground or induced noise environments.
Ordering Information
HCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577.
Option
Part
number
HCPL-M600
HCPL-M611
HCPL-M601
RoHS
Compliant
-000E
-500E
-000E
-500E
-560E
Non RoHS
Compliant
No option
#500
No option
#500
-
Package
SO-5
Surface
Mount
X
X
X
X
X
Gull
Wing
Tape&
Reel
X
X
X
UL 5000 Vrms/ IEC/EN/DIN EN
1 Minute rating
60747-5-2 Quantity
100 per tube
1500 per reel
100 per tube
1500 per reel
X
1500 per reel
SO-5
To order, choose a part number from the part number column and combine with the desired option from the op-
tion column to form an order entry. Combination of Option 00 and Option 060 is not available.
Example 1:
HCPL-M600-500E to order product of Surface Mount SO-5 package in Tape and Reel packaging with RoHS
compliant.
Example :
HCPL-M601 to order product of Surface Mount SO-5 package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks:
The notation ‘#XXX’ is used for existing products, while (new) products launched since 15
th
July 001 and RoHS compliant option will use ‘-XXXE‘.
Outline Drawing (JEDEC MO-155)
ANODE 1
4.4 ± 0.1
(0.173 ± 0.004)
6
V
CC
MXXX
XXX
7.0 ± 0.2
(0.276 ± 0.008)
CATHODE 3
5 V
OUT
4
GND
0.4 ± 0.05
(0.016 ± 0.002)
3.6 ± 0.1*
(0.142 ± 0.004)
2.5 ± 0.1
(0.098 ± 0.004)
0.102 ± 0.102
(0.004 ± 0.004)
0.15 ± 0.025
(0.006 ± 0.001)
7° MAX.
1.27 BSC
(0.050)
0.71 MIN.
(0.028)
MAX. LEAD COPLANARITY
= 0.102 (0.004)
DIMENSIONS IN MILLIMETERS (INCHES)
* MAXIMUM MOLD FLASH ON EACH SIDE IS 0.15 mm (0.006)
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
Land Pattern Recommendation
4.4
(0.17)
Schematic
+
1
I
O
1.3
(0.05)
I
F
I
CC
6
5
V
CC
V
O
2.5
(0.10)
–
3
2.0
(0.080)
8.27
(0.325)
4
HCPL-M601/11 SHIELD
GND
0.64
(0.025)
USE OF A 0.1 µF BYPASS CAPACITOR
MUST BE CONNECTED BETWEEN PINS
6 AND 4 (SEE NOTE 1).
TRUTH TABLE
(POSITIVE LOGIC)
LED
OUTPUT
ON
L
OFF
H
HCPL-M600 Schematic
3
Recommended Operating Conditions
Parameter
Input Current, Low Level
Input Current, High Level
Supply Voltage, Output
Fan Out (R
L
= 1 kΩ)
Output Pull-Up Resistor
Operating Temperature
Symbol
I
FL
*
I
FH
V
CC
N
R
L
T
A
Min.
0
5
4.5
330
-40
Max.
Units
50
µA
15
mA
5.5
V
5
TTL Loads
4,000
Ω
85
°C
* The off condition can also be guaranteed by ensuring that V
F
(off ) ≤ 0.8 volts.
Absolute Maximum Ratings
(No Derating Required up to 85°C)
Storage Temperature .............................................................................-55°C to +15°C
Operating Temperature ...........................................................................-40°C to +85°C
Forward Input Current - I
F
(see Note )...............................................................0 mA
Reverse Input Voltage - V
R
.............................................................................................5 V
Supply Voltage - V
CC
(1 Minute Maximum) ...............................................................7 V
Output Collector Current - I
O
...............................................................................50 mA
Output Collector Power Dissipation ...................................................................85 mW
Output Collector Voltage - V
O
.......................................................................................7 V
(Selection for higher output voltages up to 0 V is available)
Infrared and Vapor Phase Reflow Temperature ....................................... see below
Solder Reflow Thermal Profile
300
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
PEAK
TEMP.
245°C
PEAK
TEMP.
240°C
TEMPERATURE (°C)
200
160°C
150°C
140°C
PEAK
TEMP.
230°C
2.5°C ± 0.5°C/SEC.
30
SEC.
3°C + 1°C/–0.5°C
30
SEC.
SOLDERING
TIME
200°C
100
PREHEATING TIME
150°C, 90 + 30 SEC.
50 SEC.
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
0
0
50
100
150
200
250
TIME (SECONDS)
Note: Non-halide flux should be used.
Recommended Pb-Free IR Profile
t
p
T
p
T
L
TEMPERATURE
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
260 +0/-5 °C
217 °C
RAMP-UP
3 °C/SEC. MAX.
150 - 200 °C
T
smax
T
smin
RAMP-DOWN
6 °C/SEC. MAX.
t
s
PREHEAT
60 to 180 SEC.
25
t
L
60 to 150 SEC.
NOTES:
THE TIME FROM 25 °C to PEAK
TEMPERATURE = 8 MINUTES MAX.
T
smax
= 200 °C, T
smin
= 150 °C
t 25 °C to PEAK
TIME
Note: Non-halide flux should be used.
4
Insulation Related Specifications
Parameter
Min. External Air Gap
(Clearance)
Min. External Tracking Path
(Creepage)
Min. Internal Plastic Gap
(Clearance)
Tracking Resistance
Isolation Group (per DIN VDE 0109)
Symbol
L(IO1)
L(IO)
Value
≥5
≥5
0.08
CTI
175
IIIa
Units
mm
mm
mm
V
Conditions
Measured from input terminals
to output terminals
Measured from input terminals
to output terminals
Through insulation distance
conductor to conductor
DIN IEC 11/VDE 0303 Part 1
Material Group DIN VDE 0109
Electrical Specifications
Over recommended temperature (T
A
= -40°C to 85°C) unless otherwise specified. (See note 1.)
Parameter
Input Threshold
Current
High Level Output
Current
Low Level Output
Voltage
High Level Supply
Current
Low Level Supply
Current
Input Forward
Voltage
Input Reverse
Breakdown Voltage
Input Capacitance
Input Diode
Temperature
Coefficient
Input-Output
Insulation
Resistance
(Input-Output)
Capacitance
(Input-Output)
*All typicals at T
A
= 5°C, V
CC
= 5 V.
Symbol
I
TH
I
OH
V
OL
I
CCH
I
CCL
V
F
BV
R
C
IN
∆V
F
/∆T
A
V
ISO
R
I-O
C
I-O
Min.
Typ.*
5.5
0.4
4
6
Max.
5
100
0.6
7.5
10.5
1.75
1.85
Units
mA
µA
V
mA
mA
V
Test Conditions
V
CC
= 5.5 V, I
O
≥13 mA,
V
O
= 0.6 V
V
CC
= 5.5 V, V
O
= 5.5 V
I
F
= 50 µA
V
CC
= 5.5 V, I
F
= 5 mA,
I
OL
(Sinking) = 13 mA
V
CC
= 5.5 V, I
F
= 0 mA,
V
CC
= 5.5 V, I
F
= 10 mA,
T
A
= 5°C, I
F
=10 mA
I
F
= 10 mA
I
R
= 10 µA
Fig.
13
1
, 4,
5, 13
Note
1.4
1.3
5
1.5
3
60
-1.6
3750
10
1
0.6
pF
mV/°C
V
RMS
Ω
pF
V
F
= 0V, f = 1 MHz
I
F
= 10 mA
RH ≤ 50%, t = 1 min.
V
I-O
= 500 V
f = 1 MHz
1
3, 4
3
3
5
京公网安备 11010802033920号
EEWORLD
