the spread of smoke through HVAC air duct systems,
including low-flow applications. As a photoelectric
detector, it’s ultra-responsive to the large smoke
particles commonly found in duct systems.
The DH100ACDCLP uses low-flow technology to sense smoke in the
lowest air speeds, from 100 to 4,000 feet per minute. When smoke is
detected, all interconnected units will initiate their relays. However,
to quickly locate the fire source, only the detector sensing smoke
will alarm. Two DPDT Form-C relay contacts, connected to auxiliary
equipment, can also be configured to prevent the spread of smoke
through a particular area.
The DH100ACDCLP is simple to install and maintain. Powered by
24 VAC/DC or 120/240 VAC, it can be easily mounted to round and
rectangular ducts, from one to twelve feet in width, with outside
mounting tabs. It also offers an adjustable telescopic sampling tube
that can be used for duct widths up to 18 inches. This tube locks into
place – no additional tools are necessary.
Its modular construction allows for easy cleaning and field
replacement of the power and sensor boards. Also simplifying
maintenance is a transparent cover that provides convenient visual
inspection. If the cover is removed, a patented cover-tamper trouble
signal gives a 7-minute delay before the panel or remote accessory is
notified of trouble.
At a remote location, the remote test station option ensures that
a detector is functioning properly and the remote sounder/LED
indicator option signals if a detector is in alarm. However, the cover
does not need to be removed if a detector needs to be reset at the
detector. Simply push the built-in reset button.
WARNING:
Duct smoke detectors are
NOT
a substitute for open
area smoke detectors,
NOT
a substitute for early warning detection
and
NOT
a replacement for a building’s regular fire detection system.
Refer to NFPA 72 and 90A for additional information.
Features
• Photoelectric, low-flow technology
• An air velocity rating from 100 feet per minute to 4,000 feet per
minute (.5 meters per second to 20.32 meters per second)
• Patented interconnectability for multi-fan shutdown
• Two DPDT Form-C relay contacts
• 24 VAC/DC or 120/240 VAC
• Versatile mounting options
• Outside mounting tabs
• A patented telescopic sampling tube
• Modular construction
• A patented cover-tamper trouble signal
• A transparent cover
• A remote test station
• Remote sounder/LED indicator options
• A built-in reset button
Agency Listings
Innovair Duct Smoke Detector Specifications
Architectural/Engineering Specifications
The air duct smoke detector shall be a System Sensor Model DH100ACDCLP Series Duct Smoke Detector. The detector housing shall be UL listed per UL 268A
specifically for use in air handling systems. The detector shall operate at air velocities of 100 feet per minute to 4000 feet per minute (0.5 to 20.32 m/sec.). The
unit shall be capable of controlling up to ten (10) air handling systems when interconnected with other detectors. The detector shall be capable of providing a
trouble signal in the event that the front cover is removed. It shall be capable of local testing via magnetic switch or remote testing using the SSK451 Multi-
Signaling Accessory or the RTS451KEY Remote Test Station. The unit shall be reset by local reset button or remote test station. The duct smoke detector housing
shall incorporate an airtight smoke chamber in compliance with UL 268A, Standard for Smoke Detectors for Duct Applications. The housing shall be capable
of mounting to either rectangular or round ducts without adapter brackets. An integral filter system shall be included to reduce dust and residue effects on
detector and housing, thereby reducing maintenance and servicing. Sampling tubes shall either be telescoping or be easily installed by passing through the
duct housing after the housing is mounted to the duct. The unit shall provide a spacial separation of no less than 1⁄4˝ (6.4 mm) and/or a physical barrier between
the high and low voltage terminals. The enclosure shall meet all applicable NEC and NFPA standards regarding electrical junction boxes. Terminal connections
shall be of the strip and clamp method suitable for 12–18 AWG wiring.
Note: Alarm auxiliary contacts must switch 100mA minimum at 5VDC. Alarm auxiliary contacts shall not be connected to initiating circuits of control panels. Use
*Note: When a unit is powered at the 120 VAC input, any combination of accessories may be used such that the given accessory loads are: 60 mA or less in the
standby state; 110 mA or less in the alarm state.
A05-1044-007
Wiring Guide
System wiring diagram for 4-wire duct smoke detectors
AVAILABLE POWER INPUTS
POWER INPUTS ACCEPT
24 VDC, 24 VAC 50-60 HZ,
120 VAC 50-60 HZ, OR
220/240 VAC 50-60 HZ.
CONNECT POWER SOURCE
TO APPROPRIATE TERMINALS
OF EACH DETECTOR.
9
10
A
B
C
9
AVAILABLE POWER INPUTS
10
A
B
C
CONNECT POWER SOURCE
TO APPROPRIATE TERMINALS
OF EACH DETECTOR. SEE
SPECIFICATIONS FOR
ADDITIONAL POWER SUPPLY
INFORMATION.
24V
120
VAC
24V
120
VAC
220/240
VAC
ALARM AUXILIARY CONTACTS
FOR FAN SHUTDOWN, ETC.
18
7
17
6
16
N.C.
C.
N.O.
N.O.
C.
220/240
VAC
ALARM AUXILIARY CONTACTS
FOR FAN SHUTDOWN, ETC.
8
N.C.
16
N.C.
6
C.
17
N.O.
7
N.O.
18
C.
8
N.C.
FOR WIRING OF AUXILIARY
DEVICES, REFER TO
MANUFACTURER'S
INSTALLATION INSTRUCTIONS
OR CONTACT MANUFACTURER.
NOTE:
THE SUPERVISORY RELAY NOW
PROVIDES A "FORM C" CONTACT FOR
CUSTOMIZED APPLICATIONS.
FOR STANDARD APPLICATIONS, ONLY
THE "NO" CONTACT IS USED
AUX. CONTACT RATINGS
10A @ 30 VDC RESISTIVE
10A @ 250 VAC
100mA MINIMUM @ 5 VDC
NOT INTENDED FOR
CONNECTION TO CONTROL
PANELS.
ALARM AUXILIARY CONTACTS SHOWN IN
STANDBY. CONTACTS TRANSFER DURING
ALARM AS INDICATED BY THE ARROWS.
TROUBLE CONTACT RATING
2.0 A @ 30 VDC resistive
2.0 A @ 125 VAC resistive
SUPERVISORY TROUBLE CONTACTS
14
3
ALARM AUXILIARY CONTACTS SHOWN IN
STANDBY. CONTACTS TRANSFER DURING
ALARM AS INDICATED BY THE ARROWS.
SUPERVISORY TROUBLE CONTACTS
14
3
TROUBLE CONTACTS CLOSED IN ALARM AND STANDBY.
CONTACTS OPEN WHILE DETECTOR PCB OR POWER IS
REMOVED OR WHEN TAMPER FEATURE TIMES OUT. OPEN
CONTACTS SIGNAL TROUBLE CONDITION TO PANEL.
TROUBLE CONTACTS CLOSED IN ALARM AND STANDBY.
CONTACTS OPEN WHILE DETECTOR PCB OR POWER IS
REMOVED OR WHEN TAMPER FEATURE TIMES OUT. OPEN
CONTACTS SIGNAL TROUBLE CONDITION TO PANEL.
+
5
ALARM
INITIATION
LOOP
ALARM
INITIATION
CONTACTS
4
CONTACTS SHOWN
OPEN IN STANDBY.
CONTACTS CLOSE
IN ALARM.
ALARM
INITIATION
CONTACTS
4
5
CONTACTS SHOWN
OPEN IN STANDBY.
CONTACTS CLOSE
IN ALARM.
–
UL LISTED 4-WIRE
CONTROL PANEL
FIRST DETECTOR IN THE LOOP
DH100ACDCLP
LAST DETECTOR IN THE LOOP
DH100ACDCLP
EOL RESISTOR
SPECIFIED BY
PANEL MANUFACTURER
Wiring diagram for DH100ACDCLP to APA451:
DH100ACDCLP
Alarm Signal
Aux. Power +
Sup. N. O.
Sup. COM
Aux. Power –
15
19
14
3
20
3 Power
(Green LED)
1 Common
APA451
2 Alarm
(Red LED)
Wiring diagram for the DH100ACDCLP to
RTS451/RTS451KEY:
DH100ACDCLP
Alarm Signal
Aux. Power +
Sup. N. O.
Sup. COM
Aux. Power –
Reset
15
19
14
3
20
2
6
RTS451/RTS451KEY
1
(Red LED) Alarm
Wiring diagrams for optional accessories:
15
ALARM SIGNAL (+)
AUX POWER (–)
20
(+)
ALARM SIGNAL (+)
AUX POWER (–)
(–)
*
For RTS451KEY
only without a
control panel.
(Green LED)
Power
*
DUCT DETECTOR
DH100ACDCLP
PA400 (OPTIONAL)
AUDIBLE ALERT
DUCT DETECTOR
DH100ACDCLP
2
3
NOTE: Wiring diagram shown is for DH100ACDCLP 4-wire duct
smoke detector system equipped without a control panel.
NOTE: A trouble condition is indicated when the green LED
is not illuminated.
15
Test 11
SIGNAL (+)
ALARM
4
5
(+)
ALARM SIGNAL (+)
AUX POWER (–)
15
(+)
Wiring diagram for DH100ACDCLP to SSK451:
FIELD INSTALLED
JUMPER FOR
TEMPORAL PATTERN
SSK451
COMMON
TEMPORAL SELECT
ALARM SIGNAL
SUPERVISORY SIGNAL
RESET
TEST
POWER (–)
POWER (+)
3
2
1
4
7
8
6
5
15
3
14
2
11
20
19
ALARM SIGNAL
NO
SUPERVISORY
CONTACT
DH100ACDCLP
RESET
TEST
AUX. POWER (–)
AUX. POWER (+)
*NOTE: For RTS451KEY only without a Control
20
(–)
Panel.
RTS451 does
DUCT DETECTOR
not have a terminal 6.
PA400 (OPTIONAL)
DH100ACDCLP
AUDIBLE ALERT
NOTE: Wiring diagram shown is for DH100ACDCLP
4-wire duct smoke detector system
equipped without a control panel.
NOTE: A trouble condition is indicated when the
green LED is not illuminated.
AUX POWER (–)
RED
20
(–)
DUCT DETECTOR
DH100ACDCLP
RA400Z (OPTIONAL)
REMOTE (LED)
ANNUNCIATOR
FIELD INSTALLED
JUMPER
Important Interconnect Notes
• When using the interconnect feature, all interconnected units must be powered with the same, independent supply.
• Polarity must be maintained throughout the interconnect wiring. Connect terminal 12 on unit 1 to terminal 12 on unit 2 and so on. Similarly, connect
terminal 1 on unit 1 to terminal 1 on unit 2 and so on.
• Up to 10 units may be interconnected.
A05-1044-007
Accessories
System Sensor provides system flexibility with a variety of accessories, including two remote test stations, and several different means of
visible and audible system annunciation. As with our duct detectors, all duct smoke detector accessories are UL listed.
APA451
Piezo Annunciator
(UL S4011)
RTS451KEY
Remote Test Station
with Key (UL S2522)
PA400W
Mini-Alert Sounder
(UL S3593)
shown with PS24LOW add-on
strobe (PS12/24SLENSW smoke
lens option available)
RTS451
Remote Test Station
(UL S2522)
RA400Z
Remote Annunciator
(UL S2522)
SSK451
Multi-Signaling
Accessory
(UL 268A)
SSK451
Multi-Signaling Accessory
(UL 268A)
shown with PS24LOW add-on
strobe (PS12/24SLENSW smoke lens
option available)
Ordering Information
Part No.
DH100ACDCLP
A5190
A5064
Accessories
ST-1.5
ST-3
ST-5
ST-10
T80-71-00
P48-55-00
SSK451
RTS451KEY
RTS451
APA451
Description
4-wire photoelectric duct detector with low-flow technology
Replacement 4-wire photoelectric detector board
Replacement 4-wire power board
Metal sampling tube duct widths 1´–2´ (0.3–0.6 m)
Metal sampling tube duct widths 2´–4´ (0.6–1.2 m)
Metal sampling tube duct widths 4´–8´ (1.2–2.4 m)
Metal sampling tube duct widths 8´–12´ (2.4–3.7 m)
In the continuous increase mode, TA can generate time intervals of different cycles by setting them in the interrupt. I would like to ask,1For whom to set the value?
2 Is this value set to be the init...
PB port connected to the light PC.0 connected to an independent button (for convenience always connected to the ground) if((PINC0x0f)==0x0e) {PORTB=0x00;} else {PORTB=0x02;} This is completely correct...
The following two pictures are the internal block diagram and application circuit diagram of ADN8834 (temperature control chip).
First of all, I have a question. The chip specification recommends usin...
To measure the loss and efficiency of any system, it is best to measure the system input and output synchronously, as shown in Figure 11. [/size][/font][/color][/p][color=#333333][font=Arial, Helvetic...
As a natural human-machine interface, voice can make the in-vehicle navigation system safer and more user-friendly. Through the functional comparison of domestic and foreign in-vehicle navigation s...[Details]
In the early 1990s, portable phones were all the rage. With the rapid development of electronic technology, today's mobile phones can not only send emails and text messages, but also take photos, ch...[Details]
introduction
Oxygen is an important substance for human metabolism. Brain tissue has a high metabolic rate and consumes about 20% of the total oxygen in the body. In the clinical rescue and ...[Details]
At present, the global medical electronics industry is gradually showing attractive development prospects, and the speed of product replacement is constantly increasing. At the same time, due to the p...[Details]
Introduction
The market for wireless telemetry products is developing rapidly. Recently, the industry has also set off a revolution in wireless applications. Wireless telemetry technol...[Details]
Due to the needs of medical development, in many cases, general thermometers can no longer meet the requirements of fast and accurate temperature measurement, such as measuring human body temperature ...[Details]
0Introduction
In oil drilling, accurate measurement of wellbore posture is the premise of wellbore trajectory control. To this end, this paper fully combines the advantages of single-chip ...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
Wireless personal area networks (or WPANs) are particularly useful for sensing, monitoring, and control applications. Cost-effective WPANs have the unique potential to implement wireless connectivi...[Details]
MOSFETs are widely used as power switching elements in regulators and motor controllers. They are available as discrete devices or integrated into ICs in various H-bridge configurations.
A hig...[Details]
1 Introduction
Generally, when transmitting information over short distances through electrical signals, baseband signals can be directly transmitted. However, over long distances, baseban...[Details]
1 Introduction
Reliability research originated from weapon systems. After nearly half a century of development, it has become an engineering discipline that covers all disciplines and industri...[Details]
Introduction: Generally speaking, the power supplies used to drive today's high-resolution analog/digital converters have AC or DC loads of hundreds of ohms or more. Therefore, an operational ampli...[Details]
1 Introduction
Intelligent software agents are software programs that can perform specific tasks for users, have a certain degree of intelligence, can autonomously perform some tasks, and ...[Details]
With the improvement of people's requirements for vehicle riding comfort and the development of passenger car suspension technology in my country, air suspension is increasingly used in passenger ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
