EEWORLDEEWORLDEEWORLD

Part Number

Search

BR17A-C2-V2

Description
Power/Signal Relay, 2 Form C, DPDT, Latched, 0.063A (Coil), 12VDC (Coil), 756mW (Coil), 2A (Contact), 28VDC (Contact), DC Input, Random, AC/DC Output, Through Hole-Straight Mount,
CategoryMechanical and electronic products    relay   
File Size237KB,2 Pages
ManufacturerMicrosemi
Websitehttps://www.microsemi.com
Download Datasheet Parametric View All

BR17A-C2-V2 Overview

Power/Signal Relay, 2 Form C, DPDT, Latched, 0.063A (Coil), 12VDC (Coil), 756mW (Coil), 2A (Contact), 28VDC (Contact), DC Input, Random, AC/DC Output, Through Hole-Straight Mount,

BR17A-C2-V2 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPANEL MOUNTABLE
body width10.16 mm
body height10.41 mm
Body length or diameter20.57 mm
Maximum coil current (DC)0.063 A
Coil operating voltage (DC)8.4 V
Coil power756 mW
Coil release voltage (DC)6 V
Coil resistance190 Ω
Maximum coil voltage (DC)12 V
Nominal coil voltage12 V
Coil/Input Power TypeDC
Contact (AC) maximum rated R load2A@115VAC
Maximum contact current (AC)2 A
Maximum contact current (DC)2 A
Contact (DC) maximum rated R load2A@28VDC
Contact resistance100 mΩ
Maximum contact voltage (AC)115 V
Maximum contact voltage (DC)28 V
Contact/Output Power TypeAC/DC
Dielectric strength between coil and contacts1000 Vrms
Dielectric strength between breaking contacts500 Vrms
Input switching control typeRandom
Insulation resistance10000000000 Ω
JESD-609 codee4
Installation featuresTHROUGH HOLE-STRAIGHT MOUNT
Number of terminals8
operating hours5 ms
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
physical size20.57mm x 10.16mm x 10.41mm
GuidelineMIL-PRF-39016
Relay actionLATCHED
Relay style2 FORM C
Relay functionDPDT
Relay typePOWER/SIGNAL RELAY
release time5 ms
surface mountNO
Terminal surfaceGOLD
Terminal length0.0053 inch
Termination typeSOLDER
weight7 g
Base Number Matches1
BR17
Half-Size Crystal Can
Welded • DPDT
Dry Circuit to 2 Amps
Welded • DPDT
UNIVERSAL CONTACTS…permit
operation from dry circuit to rated load with the same contact set.
UNIQUE HEAT SINK/MAGNETIC FLUX CONDUCTOR…improves
heat dissipation characteristics— insures
lower temperature rise.
SPECIALLY-DESIGNED MAGNETIC CIRCUIT…locates
armature inside coil for more efficient switching action.
SPECIFICATIONS
GENERAL
Contact Arrangement
.........................2PDT (2 Form C)
Magnetic Latching
Weight....................................................
0.25 oz approx.
Designed to meet the requirements of MIL-PRF-39016.
PERFORMANCE
Contact Rating
(Note 1)
Resistive ............. 2 Amps @ 28 VDC or 115V 400 Hz
(Case Ungrounded)
Low Level........................... 10-50 µA @ 10-50 mv DC
or peak AC (Note 4)
Latch/Reset Power:
BR17A and BR17M ........................... 175 mw approx.
BR17B ................................................. 90 mw approx.
Latch/Reset Time..............3
ms max, excluding bounce
time at nominal coil voltage
Contact Bounce Time.....
2 ms max @ 2 Amps 28 VDC
Contact Resistance
Before Life ........................ .0.050 Ohms max @ rated
current, 6 or 28 VDC
After Life ........................... 0.100 Ohms max. @ rated
current, 6 or 28 VDC
Notes:
1. For case grounded loads and other ratings, consult the
factory.
2. For applications requiring other shock and vibration
levels, consult the factory.
3. For other ratings consult the factory.
4. Relay contacts which have switched high level currents
are no longer suitable for switching low level loads.
5. Contacts were placed in the position shown by placing
voltage with the polarity shown on the indicated coil
(reset). To switch contacts, a voltage of indicated
polarity must be applied to the other coil (Latch).
6. Contacts were placed in position shown by placing
voltage with the polarity indicated on the coil. To switch
contacts a voltage of the reverse polarity must be
applied to the coil.
ENVIRONMENTAL
o
o
Temperature Range..............................-65
C to +125 C
Vibration
(Note 2)............................. 0.4" DA 10 - 38 Hz,
20 G's 38 - 2,000 Hz
Shock (Operating)
(Note 2) .......................50 G's 11 ms
ELECTRICAL CHARACTERISTICS
Duty Cycle
.....................................................Continuous
Insulation Resistance
o
10,000 megohms @ 500V 25 C
o
1,000 megohms @ 500V 125 C
Dielectric Strength:
Sea Level:
Between Coils (BR17A & M) .................500 VRMS
Contact to Case..................................1,000 VRMS
Contact to Coil....................................1,000 VRMS
Coil to Case...........................................500 VRMS
Across Open Contacts ..........................500 VRMS
70,000 Feet
All points ................................................350 VRMS
14930 E. Alondra Blvd., La Mirada, CA 90638-5752 (714) 994-6500 FAX (714) 994-3013
W: 2000 Rev. 5
Just started using WinCE
I came into contact with WinCE yesterday. Now my concept of it is Windows CE. I don’t know anything else. I am uploading a book. I don’t know how good it is, but it is very clear. It is available for ...
hades2011 Embedded System
Tiva TM4C123GXL MCU software simulation IIC problem
It is necessary to use TM4C to read data through IIC. The hardware is not easy to transplant, so I wrote a software to simulate IIC. SDA and SCL are both externally pulled up by resistors. At the begi...
spuer_liu TI Technology Forum
Classification of power amplifiers
Power amplifiers are divided into the following four types according to their working status: (1) Class A working state The collector current of the transistor is always flowing during the entire work...
fish001 Analogue and Mixed Signal
The MSP430 LanuchPad on TI's official website is only $4.3. Who wants to organize a group purchase?
The MSP430 LanuchPad on TI's official website is only $4.3, a very exquisite little thing. Who wants to organize a group purchase?...
elulis Microcontroller MCU
Beaglebone black and MPU-6050 three-axis acceleration connection problem
I use beaglebone black to connect to MPU-6050 three-axis acceleration module (VCC3.3, GND, SDA, SCL). I use i2cdetect -y -r 1 on beaglebone black, but it doesn't find the three-axis acceleration modul...
hzm000000 DSP and ARM Processors
Reduce logic unit usage for critical signals
1. Techniques to reduce the number of combinational logic cells on the critical pathIn FPGA, each logic unit on the critical path will increase a certain delay. Therefore, in order to ensure the timin...
eeleader FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1574  2077  787  406  1830  32  42  16  9  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号