5962-9458505HBX datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9458505HBX

5962-9458505HBX: DescriptionEEPROM Module, 128KX32, 140ns, Parallel, CMOS, CQFP68, CERAMIC, QFP-68; Categorystorage storage; File Size3MB，939 Pages; ManufacturerWhite Electronic Designs Corporation; Websitehttp://www.wedc.com/

Download Datasheet Parametric View All

5962-9458505HBX Overview

EEPROM Module, 128KX32, 140ns, Parallel, CMOS, CQFP68, CERAMIC, QFP-68

5962-9458505HBX Parametric

Parameter Name	Attribute value
package instruction	CERAMIC, QFP-68
Reach Compliance Code	unknown
Maximum access time	140 ns
Other features	USER CONFIGURABLE AS 512K X 8
Spare memory width	16
JESD-30 code	S-CQFP-G68
length	23.875 mm
memory density	4194304 bit
Memory IC Type	EEPROM MODULE
memory width	32
Number of functions	1
Number of terminals	68
word count	131072 words
character code	128000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	128KX32
Package body material	CERAMIC, METAL-SEALED COFIRED
encapsulated code	QFP
Package shape	SQUARE
Package form	FLATPACK
Parallel/Serial	PARALLEL
Programming voltage	5 V
Certification status	Not Qualified
Filter level	MIL-PRF-38534 Class H
Maximum seat height	4.06 mm
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	YES
technology	CMOS
Temperature level	MILITARY
Terminal form	GULL WING
Terminal pitch	1.27 mm
Terminal location	QUAD
width	23.875 mm
Maximum write cycle time (tWC)	10 ms
Base Number Matches	1

Preview

Download Datasheet

View All

NOT MEASUREMENT

SENSITIVE

MIL-HDBK-103AP

6 MARCH 2014

SUPERSEDING

MIL-HDBK-103AN

12 SEPTEMBER 2013

DEPARTMENT OF DEFENSE

HANDBOOK

LIST OF STANDARD MICROCIRCUIT DRAWINGS

This handbook is for guidance only. Do not cite this document

as a requirement.

AMSC N/A

FSC 5962

MIL-HDBK-103AP

CONTENTS

PARAGRAPH

1.1

1.2

1.2.1

1.2.2

1.2.3

1.2.4

4.1

4.2

4.3

4.4

4.5

4.6

5.1

5.2

6.1

6.1.1

6.1.2

6.2

7.1

7.2

TABLE 1

SECTION 1

Part I

Part II

Part III

PAGE

SCOPE .......................................................................................................................................... 1

Purpose...................................................................................................................................... 1

Part or identifying number (PIN) ................................................................................................ 1

Drawing number......................................................................................................................... 1

Device class designator ............................................................................................................. 1

Case outline / lead finish ............................................................................................................ 2

Substitutability ............................................................................................................................ 2

APPLICABLE DOCUMENTS ......................................................................................................... 2

DEFINITIONS ................................................................................................................................ 2

REQUIREMENTS .......................................................................................................................... 2

Drawing requirements ................................................................................................................ 2

Preparation procedures ............................................................................................................. 2

Drawing effectivity and duration ................................................................................................. 2

Approved sources of supply....................................................................................................... 2

Radiation hardness assurance (RHA) levels ............................................................................. 2

Electrostatic discharge sensitivity (ESD) listing ......................................................................... 3

CONFIGURATION MANAGEMENT .............................................................................................. 3

Configuration management of SMDs ......................................................................................... 3

Record of users.......................................................................................................................... 3

DISTRIBUTION and REQUESTS .................................................................................................. 4

Distribution ................................................................................................................................. 4

Automatic distribution ................................................................................................................ 4

Electronic distribution ................................................................................................................. 4

Requests .................................................................................................................................... 4

NOTES .......................................................................................................................................... 4

Intended use .............................................................................................................................. 4

Subject item (key word) listing ................................................................................................... 4

Noun code descriptions ................................................................................................................. 5

Microcircuits................................................................................................................................... 12

Listed by SMD PIN .....................................................................................................................

Listed by generic PIN .................................................................................................................

714

Listed approved sources ............................................................................................................

932

Concluding material ...................................................................................................................

936

iii

MIL-HDBK-103AP

1.2.3 Case outline/lead finish. Case outline and lead finish are as described in each SMD. The lead finish indicated in the

section 1 Part I listing is the most readily available from the manufacturer listed for the part. The manufacturer is authorized to

supply other lead finishes than what is listed provided that further testing/qualification is performed by the manufacturer on the

other lead finish(es). The user needs to contact the manufacturer to determine the availability of other lead finishes not listed

herein.

1.2.4 Substitutability. Device-class-Q devices will replace device-class-M devices.

2. APPLICABLE DOCUMENTS This section is not applicable to the handbook.

3. DEFINITIONS This section is not applicable to the handbook.

4. REQUIREMENTS

4.1 Drawing requirements. SMD's will be prepared in accordance with ASME Y14.100 and DOD directives.

4.2 Preparation procedures. The procedures for the generation of an SMD are provided in MIL-HDBK-780.

4.3 Drawing effectivity and duration. SMD's and device class M one part - one part number SMDs which have become

inactive for new design are reflected in section 1, part 1 of the appendix of this document with an "I" in the status column.

4.4 Approved sources of supply. The approved sources of supply list in this handbook supersedes the approved sources

formerly listed in each individual SMD/DLA Land and Maritime Drawing. This handbook is the official list of approved sources

of supply for non-one part - one part number SMD PIN's and for device class M one part - one part number SMD PIN's. Device

classes B, S, Q, V, T, N (monolithic) and H, K, D, G, E (hybrid) one part - one part number SMD PIN's are listed for the

convenience of the users. Official listing for B, S, Q, V, T, N, H, K, D, G, and E levels are available in the applicable QML.

Manufacturers should notify DLA Land and Maritime-VA in writing if they no longer wish to be listed as an approved source of

supply for any device listed herein. This letter will be used by DSCC to remove the manufacturer from MIL-HDBK-103 for

those devices that the manufacturer specifies that he will no longer supply.

4.5 Radiation hardness assurance (RHA) levels. SMD devices which meet the RHA requirements of MIL-PRF-38535 or

MIL-PRF-38534 will be marked with the appropriate RHA designator M, D, P, L, R, F, G, or H replacing the dash (-) in the PIN

as indicated in the following example:

5962(M, D, P, L, R, F, G, or H)8999901EA

Only the highest RHA level for which the device is qualified will be listed in Section 1, Part I of the appendix of this document;

however, at the request of the customer, the manufacturer is authorized to supply any lower RHA level device. At the request

of the customer, the non-RHA PIN designated with a dash (-) may be supplied at the option of the manufacturer. The

manufacturer may also opt to submit a certificate of compliance to have the non-RHA PIN listed in addition to the RHA PIN in

Section 1, Part I of the appendix of this document.

Recommended Resources

Microwave induction automatic light turning circuit

Thyristor overcurrent protection circuit 5

Ten-octave band room equalizer circuit

Telephone automatic dialing voice alarm circuit diagram

Three-phase ladder wave inverter output transformer winding connection method and output voltage waveform

Computer motherboard circuit diagram 815 1_25

RPC Server is implemented under VxWorks. How can I access it on a WINDOWS PC?: My device runs VxWorks, which implements an RPC server. The documentation says that it complies with SUN's RPC specification (RFC1057). Now I need to access this RPC server on the Windows platform. Ho...; zsk001 Real-time operating system RTOS

How to map physical addresses in user-mode drivers in WinCE6.0: I would like to ask you experts: How to map physical addresses in user-mode drivers in WinCE6.0? For the following code, if this driver is run in user mode, the output vpReg is 0. If anyone knows how ...; happyjinwen Embedded System

LCD12864 Data Sheet: ...; 张丽山 FPGA/CPLD

Simple PCB keypad problem: It is a simple keypad, and the control and power circuits are on other PCB boards. I am currently routing all the wires (including the ground wire) on the top layer. I would like to ask if both the to...; 拜月神教1234 PCB Design

Database development under wince5.0+evc4.0+sql ce solution: wince5.0 does not support ADOCE. Has anyone done database development under the wince5.0+evc4.0+sql ce solution? Please give me some advice....; lixiqin12345 Embedded System

Why do some designs connect dozens of capacitors in parallel?: Why do some designs connect dozens of capacitors in parallel to a network (power supply) with the same name instead of using a few capacitors with relatively large capacitance? I hope experts can give...; qq413243608 stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components