Exceeding any one or a combination of the Absolute
Maximum Rating conditions may cause permanent
damage to the device. Extended application of Absolute
Maximum Rating conditions to the device may reduce
device reliability. Specified typical performance or
functional operation of the device under Absolute
Maximum Rating conditions is not implied.
Nominal Operating Parameters
Specification
Parameter
Min
General Performance
Frequency of Operation
Supply Voltage (V
S
)
Supply Current
Tuning Voltage (V
TUNE
)
Tuning Sensitivity
Output Power
Output Phase Noise at 10kHz
Output Phase Noise at 100kHz
2nd Harmonic
Frequency Pushing
Frequency Pulling (2:1 VSWR)
RF Output Return Loss
Frequency Drift Rate
V
TUNE
Port Input Capacitance
Thermal Resistance
5.0
4.75
40
0
390
3
-72
-96
-20
18
5
9
-0.7
4
45
5.00
52
10.0
5.25
70
18
GHz
V
mA
V
MHz/V
dBm
dBc/Hz
dBc/Hz
dBc
MHz/V
MHz pp
dB
MHz/°C
pF
°C/W
Junction to paddle
Recommended operating range.
Unit
Typ
Max
Condition
V
S
= 5V, Freq = 5GHz to 10GHz, T = 25°C unless noted
otherwise.
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS140501
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
2 of 6
RFVC1801
Typical Evaluation Board Performance: (V
S
= 5.0V, unless noted)
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS140501
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
3 of 6
RFVC1801
Pin Out
Pin Names and Descriptions
Pin
1-3
4
5-11
12
13
14
15
16
17-24
PADDLE
Name
N/C
VTUNE
N/C
VS
N/C
GND
RFOUT
GND
N/C
GND
No internal connection. Connect to PCB ground.
VCO control voltage input.
No internal connection. Connect to PCB ground.
Description
Supply voltage input for the VCO and Buffer stage.
No internal connection. Connect to PCB ground.
Pin internally bonded to package paddle. Connect to PCB ground.
VCO RF output. Pin is internally DC-blocked.
Pin internally bonded to package paddle. Connect to PCB ground.
No internal connection. Connect to PCB ground.
Exposed paddle on backside needs to be soldered to PCB ground.
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS140501
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
4 of 6
RFVC1801
Package Drawing
(Dimensions in millimeters)
Notes:
1. Dimensions are for reference only.
2. Package body material: Alumina.
3. Lead and paddle plating: Au, 30µm minimum.
Recommended PCB Layout
RF Micro Devices Inc. 7628 Thorndike Road, Greensboro, NC 27409-9421
For sales or technical support, contact RFMD at +1.336.678.5570 or
customerservice@rfmd.com.
DS140501
The information in this publication is believed to be accurate. However, no responsibility is assumed by RF Micro Devices, Inc. ("RFMD") for its use, nor for any infringement of patents or other rights of
third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent rights of RFMD. RFMD reserves the right to change component circuitry, recommended
application circuitry and specifications at any time without prior notice.
My 51 development board, SPI reads and writes SD card, and there is a problem when reading the SD card sector data. No data can be read at all, that is, the data is all 0. My initialization process is...
Hello everyone, please help me look at the signal transmission line in the figure below. The transmission distance is about 30m. +-12V is used to power the op amp and other chips on the circuit board ...
From an engineering perspective, we have three methods to interconnect independent digital network video servers to exchange programs and information: 1. Use independent storage physical media such as...
I would like to ask: Without EBOOT, how can I divide my NANDFLASH into two FAT areas? Thank you! My BOOT is compiled with ADS, and the OS is WINCE4.2. How can I divide the FLASH into two FAT drive let...
I want to ask how to set breakpoints in the program for debugging in Lingyang MCU? The problem I encountered is that after I set the breakpoints, the breakpoints are grayed out when the program is exe...
Medical and industrial applications often require isolation voltages of 2500Vac or higher for patient and equipment operator safety. The isolation barrier must not only transmit power to the sensin...[Details]
A biped robot joint constructed by pneumatic artificial muscles is introduced. The joint uses the flexible characteristics of pneumatic artificial muscles to effectively control the impact of the la...[Details]
Obtaining real-time and reliable traffic information has always been a bottleneck problem in the development of intelligent transportation systems. The establishment of an intelligent transportatio...[Details]
This issue will briefly introduce the test related to spectrum - occupied bandwidth.
Definition: Occupied bandwidth refers to the bandwidth corresponding to 99% of the total transmitted power, cent...[Details]
Engineers who are new to wireless design and wireless product development need to master the basics of
RF measurement
. In many cases, this process is to enable engineers who have been engag...[Details]
The overcurrent and overheating coordinated protection technology implemented by polymer positive temperature coefficient devices (PPTC) can protect motors, controllers and electronic components in...[Details]
Designers of handheld products such as cell phones, digital cameras, MP3 players and personal digital assistants (PDAs) are continually challenged to deliver more functionality in a smaller form...[Details]
Semiconductor devices used in high-end computing (advanced microprocessors) and consumer electronics (graphics and gaming chipsets) devices generally provide data rates up to 6.4Gbps through hig...[Details]
Preface
In the analog era, due to the unchanged specifications and relatively simple device connections, as well as users' low requirements for image quality, the relatively simple environment...[Details]
Multiple Input and Multiple Output (MIMO) technology is arguably the next most important development in wireless communication technology since the advent of digital communications. Many new wir...[Details]
Murphy's Law tells us that "what can go wrong, will go wrong". In the testing or production process of video equipment, problems often occur when we least want them to happen and when it is leas...[Details]
introduction
With the improvement of social automation, human-computer interaction capabilities urgently need a major change, and develop in a direction that is more convenient to use and more...[Details]
The discipline of HHCE (Home Health Care Engineering) is gradually entering people's lives as people pay more attention to health and telemedicine develops. It advocates the concept of "seeking m...[Details]
In the WTK22wtklibdevicesDefaultColorPhoneDefaultColorPhone.properties file in the WTK directory, there is a line touch_screen=false. Change it to true.
MIDP2.0 has three touch screen methods:...[Details]
At present, ECG monitoring systems that mainly collect, analyze and diagnose ECG signals have been widely used, and have played a great role in the prevention and diagnosis of heart diseases.
...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
